TOKO TK15326MTL Datasheet
TK15326
+
-
+
-
+
-
+
-
Ach
Bch
1ch-in
Ach
Bch
2ch-in
V
CC
1 ch out
1KEY
2 ch out
2KEY
GND
V
EE
Audio Analog Switch
FEATURES
■ Wide Operating Voltage Range (±2 to ±7 V)
■ Low Distortion (typ. 0.003%)
■ Wide Dynamic Range (typ. 6 V
P-P
)
■ Low Output Impedance (typ. 20 Ω)
■ Low Switching Noise (typ. 3 mV)
DESCRIPTION
The TK15326M is an Analog Switch IC that was developed
for audio frequency. Function is to select one output from
two inputs in a device that includes two circuits, and the
channel can be changed by high level. The TK15326M
has a dual power supply and the input bias is direct
coupling at GND level. Because the distortion is very low,
the TK15326M fits various signals switching. It is best
suited for Hi-Fi devices. Operating voltage is wide, the
circuit plan is simple. The TK15326M is available in a small
plastic surface mount package (SSOP-12).
APPLICATIONS
■ Audio Systems
■ Radio Cassettes
1ch-in 2ch-in
TK15326
V
CC
Bch
OUT
Ach
1KEY
GND
V
EE
11
Bch
10
OUT
9
Ach
8
2 KEY
NC
7
BLOCK DIAGRAM
ORDERING INFORMATION
TK15326M
June 1999 TOKO, Inc. Page 1
Tape/Reel Code
TAPE/REEL CODE
TL: Tape Left
TK15326
Logic
Input Key
ABSOLUTE MAXIMUM RATINGS
Supply Voltage ...................................................... ±7.5 V
Power Dissipation (Note 5) ................................ 350 mW
Storage Temperature Range ................... -55 to +150 °C
Operating Temperature Range ...................-20 to +75 °C
CONTROL SECTION
Input Voltage ................................... -0.3 V to VCC + 0.3 V
TK15326M ELECTRICAL CHARACTERISTICS
Test conditions: V
LOBMYSRETEMARAPSNOITIDNOCTSETNIMPYTXAMSTINU
= ±4 V, T
CC
= 25 °C, unless otherwise specified.
A
ANALOG SWITCH SECTION
Signal Input Voltage ........................ VEE - 0.3 to VCC + 0.3
Signal Output Current ............................................. 3 mA
Operating Voltage Range............................... ±2 to ±7 V
Maximum Input Frequency..................................100 kHz
I
CC
tnerruCylppuS 2.32.5Am
NOITCESLORTNOCYEK
V
LI
V
HI
Z
NI
ecnadepmItupnI 05kΩ
leveLwoLegatloVtupnI1etoN3.0-8.0+V
leveLhgiHegatloVtupnI8.1V
CC
NOITCESHCTIWSGOLANA
DHTnoitrotsiDcinomraHlatoTV
N
L
esioNlaudiseR2etoN01smrVµ
OSInoitalosI
PESnoitarapeS
NI
V
NI
3etoN
V
NI
3etoN
zHk1=f,smrV1=300.0600.0%
,zHk01=F,smrV1=
,zHk01=f,smrV1=
57-Bd
08-Bd
NYDleveLlangiStupnImumixaM%1.0=DHT,zHk1=f0.2smrV
AVGniaGegatloVzHk02~=f0Bd
V
∆V
tnec
egatloV
egatloVlanimreTtuptuO
lanimreTtuptuO-tupnI
tnec
ecnereffiD
saiBDNG2.0-02.0+V
lennahcemasneewteB331Vm
3.0+V
I
NI
Z
TUO
Note 1: The KEY input equivalent circuit is shown in Figure A.
1 channel and 2 channel is the separate action by 1Key pin and 2 key pin. When the control pin is
open, it is outputted low level (about 1.4 V). Then the A channel input signal is outputted. The
change is carried out at high level.
Note 2: The specification means a value as measurement-input terminal connects to ground
through a capacitor.
Note 3: ISO is a cross talk between A channel and B channel, SEP is a cross talk between 1 channel and 2
channel. The specification means a value as measurement-input termianl connects to ground
through 10 kΩ resistor and capacitor.
Note 4: Input equivalent circuit is shown in Figure B. The standard application of TK15326M is the direct
connecting with the GND bias. When connecting a capacitor, then to supply a bias voltage from
GND to input be any resistor is necessary.
Note 5: Power dissipation is 350 mW when mounted as recommended. Derate at 3.0 mW/°C for operation
above 25°C.
Page 2 June 1999 TOKO, Inc.
tnerruCsaiBtupnI4etoN5.0Aµ
ecnadepmItuptuOecnadepmICD02
V
CC
Input
Figure A
Figure B
Ω
V
EE
TEST CIRCUITS AND METHODS
V
SW6
SW7
CC
SW3
50 kΩ
TK15326
1 kHz
1 Vrms
or
2 Vrms
SW9
~
10 kHz
1 Vrms
~
SW8
+
10 µF
10 kΩ
SW5
+
10 µF
SW4
SW2
V
~
1: The above condition represents 1ch.
2: The above conditions distortion rate of 1-Ach and dynamic range measurement.
3: SW5 is for residual noise measurement.
4: SW8 is for cross talk (ISO or SEP) measurement.
SUPPLY CURRENT (FIGURE 1)
This current is a consumption current with a nonloading
condition.
1) Bias supply to Pins 2,4,9,11. (This condition is the same
with other measurements, omitted from the next for
simplicity)
2) Measure the inflow current to Pin 1 from VCC. This current is
the supply current.
50 kΩ
33 µF
+
SW1
V
THD
_
+
33 µF
V
EE
CONTROL LOW/HIGH LEVEL (FIGURE 2)
This level is to measure the threshold level.
1) Input, the VCC to Pin 1 and input V
to Pin 12. (This
EE
condition is the same with other measurements, omitted
from the next for simplicity)
2) Input to Pin 4 with sine wave (f = 1 kHz, VIN = 1 Vrms).
3) Connect an oscilloscope to Pin 3.
4) Drop the control voltage gradually from VCC until the
sine wave appears at the oscilloscope. This voltage is
the threshold level when the wave appears.
CC
AV
50 K
50 K
50 K
50 K
V
EE
Figure 1
V
CC
+
~
Cont.
+
+
V
EE
Figure 2
June 1999 TOKO, Inc. Page 3
TK15326
V
CC
Cont.
+
+
V
EE
+
TEST CIRCUITS AND METHODS (CONT.)
CONTROL INPUT IMPEDANCE (FIGURE 3)
This is the input resistance of the control terminal.
1) Measure the inflow current from VCC to Pin 5.
2) Calculate:
IMP = VCC / Inflow Current
This resistance is the input impedance.
V
CC
+
Figure 4
+
V
EE
Figure 3
VOLTAGE GAIN (FIGURE 5)
This is the output level against input level.
1) Pin 5 is in the open condition, or low level.
2) Connect AC volt meters to Pin 4 and Pin 3.
(Using the same type meter is best)
TOTAL HARMONIC DISTORTION (FIGURE 4)
Use the lower distortion oscillator for this measurement
because distortion of the TK15326 is very low.
1) Pin 5 is in the open condition, or low level.
2) Connect a distortion analyzer to Pin 3.
3) Input the sine wave (1 kHz, 1 Vrms) to Pin 4.
4) Measure the distortion of Pin 3. This value is the
distortion of 1-Ach.
5) Next connect Pin 5 to the VCC, or high level.
6) Input the same sine wave to Pin 2.
7) Measure in the same way. This value is the distortion
3) Input a sine wave (f = max. 20 kHz, 1 Vrms) to Pin 4.
4) Measure the level of Pin 4 and name this V1.
5) Measure the level of Pin 3 and name this V2.
6) Calculate Gain = 20 Log (( |V2 - V1| )/V1)
V1<V2 + Gain, V1>V2 - Gain
This value is the voltage gain of 1-Ach.
7) Next, connect Pin 5 to the VCC, or high level.
8) Input the same sine wave to Pin 2.
9) Measure and calculate in the same way.
This value is the maximum input level of 1-Bch.
of 1-Bch.
Page 4 June 1999 TOKO, Inc.
Loading...