1. SAFETY PRECAUTIONS
• Be sure to read the instructions in this section
carefully before use.
• Make sure to observe the instructions in this
manual as the conventions of safety symbols and
messages regarded as very important precautions
are included.
• We also recommend you keep this instruction
manual handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are
used in this manual to prevent bodily injury and
property damage which could result from
mishandling. Before operating your product, read this
manual first and understand the safety symbols and
messages so you are thoroughly aware of the
potential safety hazards.
When Installing the Unit
• Do not expose the unit to rain or an environment
where it may be splashed by water or other liquids,
as doing so may result in fire or electric shock.
• Use the unit only with the voltage specified on the
unit. Using a voltage higher than that which is
specified may result in fire or electric shock.
• Do not cut, kink, otherwise damage nor modify the
power supply cord. In addition, avoid using the
power cord in close proximity to heaters, and never
place heavy objects -- including the unit itself -- on
the power cord, as doing so may result in fire or
electric shock.
• Avoid installing or mounting the unit in unstable
locations, such as on a rickety table or a slanted
surface. Doing so may result in the unit falling
down and causing personal injury and/or property
damage.
• To prevent lightning strikes, install the unit at least
five meters away from a lightning rod, and yet
within the protective range (angle of 45°) of the
lightning conductor. Lightning strikes may cause a
fire, electric shock or personal injury.
• Since the unit is designed for in-door use, do not
install it outdoors. If installed outdoors, the aging of
parts causes the unit to fall off, resulting in personal
injury. Also, when it gets wet with rain, there is a
danger of electric shock.
When the Unit is in Use
• Should the following irregularity be found during
use, immediately switch off the power, disconnect
the power supply plug from the AC outlet and
contact your nearest TOA dealer. Make no further
attempt to operate the unit in this condition as this
may cause fire or electric shock.
· If you detect smoke or a strange smell coming
from the unit.
· If water or any metallic object gets into the unit
· If the unit falls, or the unit case breaks
· If the power supply cord is damaged (exposure of
the core, disconnection, etc.)
· If it is malfunctioning (no tone sounds.)
• Do not place cups, bowls, or other containers of
liquid or metallic objects on top of the unit. If they
accidentally spill into the unit, this may cause a fire
or electric shock.
• Do not touch the unit's antennas during thunder
and lightning, as this may result in electric shock.
Please follow the instructions in this manual to
obtain the optimum results from this unit.
We also recommend that you keep this manual
handy for future reference.
WT-3810WIRELESS TUNER
OPERATING INSTRUCTIONS
WARNING
Indicates a potentially hazardous situation which,
if mishandled, could result in death or serious
personal injury.
When Installing the Unit
• Never plug in nor remove the power supply plug
with wet hands, as doing so may cause electric
shock.
• When unplugging the power supply cord, be sure
to grasp the power supply plug; never pull on the
cord itself. Operating the unit with a damaged
power supply cord may cause a fire or electric
shock.
• When moving the unit, be sure to remove its power
supply cord from the wall outlet. Moving the unit
with the power cord connected to the outlet may
cause damage to the power cord, resulting in fire or
electric shock. When removing the power cord, be
sure to hold its plug to pull.
• The socket outlet shall be installed near the
equipment and shall be easily accessible.
• Avoid installing the unit in humid or dusty locations,
in locations exposed to the direct sunlight, near the
heaters, or in locations generating sooty smoke or
steam as doing otherwise may result in fire or
electric shock.
When the Unit is in Use
• Do not place heavy objects on the unit as this may
cause it to fall or break which may result in
personal injury and/or property damage. In
addition, the object itself may fall off and cause
injury and/or damage.
• Make sure that the volume control is set to
minimum position before power is switched on.
Loud noise produced at high volume when power is
switched on can impair hearing.
• Never open the unit case as there are high
temperature parts inside the unit, which may cause
a burn if touched. Refer all servicing to your
nearest TOA dealer.
• Use the dedicated AC – DC adapter for the unit.
Note that the use of other adapter may cause a
fire.
• If dust accumulates on the power supply plug or in
the wall AC outlet, a fire may result. Clean it
periodically. In addition, insert the plug in the wall
outlet securely.
• Switch off the power, and unplug the power supply
plug from the AC outlet for safety purposes when
cleaning or leaving the unit unused for 10 days or
more. Doing otherwise may cause a fire or electric
shock.
CAUTION
Indicates a potentially hazardous situation which,
if mishandled, could result in moderate or minor
personal injury, and/or property damage.
2. GENERAL DESCRIPTION
The WT-3810 Wireless Tuner is designed for use on the VHF band, and suitable for vocal or speech
reinforcement applications. It features a compander circuit which minimizes the influence of ambient noise.
3. FEATURES
• 6 different operating frequencies ranging from 169 to 216 MHz.
• Optimized PLL-synthesizer minimizes the oscillation frequency drift resulting from the ambient temperature
change.
• Compact size and high reliability
4. HANDLING PRECAUTIONS
• When installing, keep the unit as far away as possible from fluorescent lamps, digital equipment, personal
computers, and other equipment that generate high frequency noise.
• When cleaning the case, use a dry cloth. Never use benzine, thinner or other volatile liquids.
• When using two or more wireless microphones, keep them at least 50 cm away from each other to avoid
malfunctions or noise.
5. NOMENCLATURE AND FUNCTIONS
[Front]
[Rear]
1
2
3 4 5 6
7
8
9
1. Antenna
Raise the two antennas at a 45° angle outwards
from a vertical line. Do not raise the antennas
when carrying the tuner.
2. Volume control
Controls the output level.
3. Channel select switch
Used to select the frequency. (The tuner
frequency must be identical to that of the
microphone.)
4. Reception lamps
Either lamp, A or B, lights yellow when the tuner
receives a radio signal.
5. AF peak lamp
Lights red when the tuner output level reaches the
point about 3 dB below the clipping level.
6. Power lamp
Lights green when the DC power is supplied from
the DC power supply unit to the tuner.
7. AF output
Unbalanced phone jack
–20 dB/600 Ω. (0 dB = 1 V)
8. AF mixing input (unbalanced)
Connects to other unit's AF output.
Input level: –20 dB, 10 kΩ (0 dB = 1 V)
9. DC input jack
Connects to the DC power supply unit. Because
the tuner is equipped with no power switch, it
automatically turns on when the DC power supply
is connected to this jack and wall AC outlet.
Disconnect the DC power supply unit from the AC
outlet when the tuner is not in use.
6. OPERATION
Step 1. Connect the DC power supply unit to the unit's DC input jack and wall AC outlet.
The power is turned on and the power lamp lights.
Step 2. Set the wireless microphone switch to the ON position.
The reception lamp lights when the tuner receives the same frequency signal.
Step 3. Adjust the volume control.
The output level increases as the volume is turned clockwise, and decreases as turned
counterclockwise.
2
3
1
Printed in Taiwan
133-07-215-80
7. CHANNEL NUMBER SETTING
Turn the Channel Select switch to select the same channel number as that of the wireless microphone. A total
of 6 different channel numbers are made available for selection from 1 – 6.
1
2
3
4
5
6
Front panel
Channel select switch
CHANNEL
8. SPECIFICATIONS
* 0 dB = 1 V
Note: The design and specifications are subject to change without notice for improvement.
• Accessory
AC – DC adapter ........................................ 1
Power Source AC mains (Supplied AC – DC adapter must be used.)
Power Consumption 150 mA (13.8 V DC)
Receiving Frequency 169 – 216 MHz, VHF
Selectable Channel 6 channels
Receiving System Double superheterodyne
Diversity System Space diversity
Output –20 dB*, 600 Ω, Phone jack (unbalanced)
Mixing Input –20 dB*, 4 kΩ, Phone jack (unbalanced)
Antenna Rod antenna
Receiving Sensitivity Better than 80 dB, S/N ratio (20 dBµV input, 40 kHz deviation)
Squelch Sensitivity 18 dBµV
Squelch System Using together of noise SQ and carrier SQ
S/N Ratio Better than 100 dB (A-weight)
Harmonic Distortion Less than 1%
Frequency Response 100 – 12,000 Hz, ±3 dB
Operating Temperature –10 to +50°C
Finish Resin, dark gray
Dimensions 240 (w) x 35 (h) x 110 (d) mm
Weight 380 g
Loading...