TOA SX-200IP, SX-2000SM, SX-2000CO, SX-2000AO, SX-2100AO Instructions

...

OPERATING INSTRUCTIONS

MATRIX SYSTEM SX-2000 SERIES

Thank you for purchasing TOA's Matrix System. Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.

TABLE OF CONTENTS

1. NOMENCLATURE AND FUNCTIONS

Front ....................................................................................................................... 1-2

2. OPERATING SETTINGS DATA (DIP Switch 2 Operation)

2.1. Using Settings Data ........................................................................................ 1-4

2.2. Inserting a CF Card ......................................................................................... 1-4

3. OUTPUTTING LOG DATA (Operating DIP Switches 1 and 2) ....... 1-5

1. NOMENCLATURE AND FUNCTIONS

Front ....................................................................................................................... 2-2

Fluorescent Display ............................................................................................... 2-4

2. KEY LOCK SETTINGS AND CANCELLATION (DIP Switch 1 Operation)

............................................................................. 2-6

3. OPERATING THE MENU SCREEN

3.1. Menu Screen Operation Keys ......................................................................... 2-7

3.2. Menu Screen Hierarchical Chart ..................................................................... 2-8

3.3. Explanations of Menu Screen Items ............................................................... 2-9

1. NOMENCLATURE AND FUNCTIONS

Front ....................................................................................................................... 3-2

Fluorescent Display ............................................................................................... 3-4

2. KEY LOCK SETTINGS AND CANCELLATION (DIP Switch 1 Operation)

............................................................................. 3-6

3. OPERATING THE MENU SCREEN

3.1. Menu Screen Operation Keys ......................................................................... 3-7

3.2. Menu Screen Hierarchical Chart ..................................................................... 3-8

3.3. Explanations of Menu Screen Items ............................................................... 3-9

1. NOMENCLATURE AND FUNCTIONS

Front ....................................................................................................................... 4-2

Fluorescent Display ............................................................................................... 4-4

2. KEY LOCK SETTINGS AND CANCELLATION (DIP Switch 1 Operation)

............................................................................. 4-6

3. OPERATING THE MENU SCREEN

3.1. Menu Screen Operation Keys ......................................................................... 4-7

3.2. Menu Screen Hierarchical Chart ..................................................................... 4-8

3.3. Explanations of Menu Screen Items ............................................................... 4-9

CHAPTER 4: SX-2000AO AUDIO OUTPUT UNIT

CHAPTER 3: SX-2100AI AUDIO INPUT UNIT

CHAPTER 2: SX-2000AI AUDIO INPUT UNIT

CHAPTER 1: SX-2000SM SYSTEM MANAGER

1. NOMENCLATURE AND FUNCTIONS

Front ....................................................................................................................... 5-2

Fluorescent Display ............................................................................................... 5-4

2. KEY LOCK SETTINGS AND CANCELLATION (DIP Switch 1 Operation)

............................................................................. 5-6

3. OPERATING THE MENU SCREEN

3.1. Menu Screen Operation Keys ......................................................................... 5-7

3.2. Menu Screen Hierarchical Chart ..................................................................... 5-8

3.3. Explanations of Menu Screen Items ............................................................... 5-9

1. NOMENCLATURE AND FUNCTIONS ...................................................... 6-2

1. NOMENCLATURE AND FUNCTIONS ...................................................... 7-2

1. NOMENCLATURE AND FUNCTIONS ...................................................... 8-2

2. INDICATOR STATUS

2.1. Indicators During Zone Selection .................................................................... 8-4

2.2. Talk Key Indicators ......................................................................................... 8-5

2.3. Indicators When Changing BGM Patterns ...................................................... 8-6

2.4. Indicators During General-Purpose Pattern Broadcast ................................... 8-6

2.5. Indicators During Lamp Test ........................................................................... 8-7

2.6. Indicators on Failure Output Receipt .............................................................. 8-8

2.7. Indicators at the Time of Failure Output Reset ............................................... 8-9

2.8. Indicator State at the Time of Emergency Broadcast Pattern Start .............. 8-10

2.9. Indicator State at the Time of Emergency Broadcast Pattern Stop .............. 8-11

2.10. Indicator State at the Time of Emergency Sequence Stop ........................... 8-11

2.11. Indicator State at the Time of Emergency Sequence Phase Shift ................ 8-12

2.12. Indicator State at the Time of Emergency Reset .......................................... 8-13

1. NOMENCLATURE AND FUNCTIONS

1.1. RM-200SA ...................................................................................................... 9-2

1.2. RM-210 ........................................................................................................... 9-4

2. INDICATOR STATUS

2.1. Indicators During Zone Selection .................................................................... 9-5

2.2. Talk Key Indicators ......................................................................................... 9-6

2.3. Indicators When Changing BGM Patterns ...................................................... 9-6

2.4. Indicators During General-Purpose Pattern Broadcast ................................... 9-7

CHAPTER 9: RM-200SA REMOTE MICROPHONE

RM-210 REMOTE MICROPHONE EXTENSION

CHAPTER 8: RM-200SF FIREMAN'S MICROPHONE

CHAPTER 7: SX-2000CO CONTROL OUTPUT UNIT

CHAPTER 6: SX-2000CI CONTROL INPUT UNIT

CHAPTER 5: SX-2100AO AUDIO OUTPUT UNIT

2.5. Indicators During General EV Broadcasts ...................................................... 9-7

2.6. Indicators Showing RM Broadcast Status ....................................................... 9-8

2.7. Indicators During Lamp Test ........................................................................... 9-8

2.8. Indicators on Failure Output Receipt .............................................................. 9-9

2.9. Indicators at the Time of Failure Output Reset ............................................. 9-10

2.10. Indicator State at the Time of Emergency Broadcast Pattern Start .............. 9-11

2.11. Indicator State at the Time of Emergency Broadcast Pattern Stop .............. 9-12

2.12. Indicator State at the Time of Emergency Sequence Stop ........................... 9-12

2.13. Indicator State at the Time of Emergency Sequence Phase Shift ................ 9-13

2.14. Indicator State at the Time of Emergency Reset .......................................... 9-14

1. BGM AND GENERAL BROADCASTING

1.1. Broadcasting from the SX-2000AI, SX-2100AI, SX-2000AO, or SX-2100AO

1.1.1. Broadcasting using th function key ..................................................... 10-2

1.1.2. Broadcasting using the channel key ................................................... 10-3

1.2. Broadcasting from the RM-200SF, RM-200SA, and RM-210 ....................... 10-4

1.2.1. Example of broadcasting to the selected (pattern-designated) zone .. 10-5

1.2.2. Example of broadcasting to the selected (individual) zone ................. 10-6

1.2.3. Example of BGM broadcasting ........................................................... 10-7

1.2.4. Example of general broadcasting ....................................................... 10-7

1.2.5. Example of general EV broadcasting ................................................. 10-8

2. MAKING GENERAL URGENCY ALL-CALLS

2.1. Making General Urgency All-Calls from the RM-200SA ............................... 10-9

2.2. Making General Urgency All-Calls from the RM-200SF ............................. 10-10

3. EMERGENCY BROADCASTS

3.1. Typical System Examples ........................................................................... 10-11

3.2. Remote Microphone Operation Example .................................................... 10-13

4. MAKING LOCAL BROADCASTS (SX-2100AO only) .................... 10-16

5. ADJUSTING INPUT/OUTPUT VOLUME ............................................. 10-17

6. MONITORING INPUT/OUTPUT CHANNELS ..................................... 10-18

7. DETECTING FAULT

7.1. Fault Detection Setting Example ................................................................. 10-19

7.2. Case Example of Malfunction ..................................................................... 10-20

7.3. Remote Microphone's Operation Example ................................................. 10-21

7.4. SX-2000SM's Operation Example .............................................................. 10-22

7.5. Example of Executing the Failure Reception and Failure Reset

by Way of the Control Input Terminals ....................................................... 10-24

8. LAMP TEST

8.1. Remote Microphone's Operation Example ................................................. 10-25

8.2. SX-2000SM's Operation Example .............................................................. 10-26

CHAPTER 10: OPERATION

Chapter 1

SX-2000SM SYSTEM MANAGER

The SX-2000SM System Manager is capable of performing audio signal routing and priority control for the entire SX-2000 system. It comes with 8 control inputs, 8 control outputs, failure status output, failure status input, and other functions that include keys, access indicators, mode indicators and failure indicators, enabling a wide range of control and status monitoring. Each function can be set using the SX-2000 Setting Software, and the settings data saved to a Compact Flash (CF) card. By inserting the programmed CF card into the SX-2000SM, each control can be performed for the entire system. It is also possible to record the entire system's operation log and store its contents on the CF card as an operation log. The SX-2000SM is a 1U-size* unit that can be mounted in an EIA equipment rack. It has two power supply inputs, one of which can be connected to a backup power source to protect against power failures.

*1U size = 44.5 mm (standard size)

1-2

Chapter 1: SX-2000SM SYSTEM MANAGER

1. NOMENCLATURE AND FUNCTIONS

[Front]

1. LAN Indicator [LAN] (Green)

Lights when the LAN connection terminal on the rear panel is connected, and flashes during LAN communications.

2. SX Link A Indicator [SX LINK A] (Green)

Lights when the SX Link A connection terminal on the rear panel is connected, and flashes while communications are being performed via the SX Link A terminal.

3. SX Link B Indicator [SX LINK B] (Green)

Lights when the SX Link B connection terminal on the rear panel is connected, and flashes while communications are being performed via the SX Link B terminal.

4. Emergency Indicator [EMERGENCY] (Red)

Lights while the general urgency all-call is being made (p. 10-9) or when the SX-2000 system is in an emergency condition, and flashes when a 24 V emergency cutoff* state occurs involving any SX2000AO within the system.

* In the SX-2000 system, a 24 V emergency cutoff

input terminal that allows control of an emergency audio input is provided on the SX2000AO's rear panel. When the SX-2000 system is combined with another emergency broadcast system, a 24 V DC is normally kept being

supplied to this emergency cutoff input terminal and is cut off (24 V emergency cutoff function) in emergency situations. This interrupts the general-purpose broadcast from the SX-2000, allowing the emergency broadcast system to override it. (For details, see the separate Installation Manual, "Installation.")

5. CPU OFF Indicator [CPU OFF] (Red)

Lights while the general urgency all-call (CPU OFF state) is being made (p. 10-9).

6. Standby Indicator [STANDBY] (Green)

Lights when the SX-2000 system is operating on the backup power supply during power failures. It also lights when the system reset cannot be performed using the SX-2000 Setting software. Note that if the standby indicator lights, it is not possible to restart your SX-2000SM using the Setting software. To perform system reset, press the Reset key (15) inside the protective cover to restart.

7. General Indicator [GENERAL] (Yellow)

Lights while the general urgency all-call is being made (p. 10-9) or when a failure is detected in the SX-2000SM. Lights or flashes when a failure is detected in the system.

1 2 3

Inside of the protective cover

15 16 18 1917

4 5 6

Protective cover

7 8 9

10 11 12

13 14

1-3

Chapter 1: SX-2000SM SYSTEM MANAGER

8. CPU Indicator [CPU] (Yellow)

Lights while the general urgency all-call is being made (p. 10-9) or when a failure is detected in the SX-2000SM.

9. SX Link Indicator [SX LINK] (Yellow)

Flashes when a cable is connected to neither the rear panel-mounted SX Link terminal A nor B.

10. Fault Ack Key [FAULT ACK]

The buzzer will sound when a failure is detected in the SX-2000 system. Press this key to stop the buzzer.

11. Fault Reset Key [FAULT RESET]

Pressing this key resets the failure information (the buzzer and fault indicators) for the entire SX-2000 system. Set the mode for operation method using DIP switch 4 (19).

12. Lamp Test Key [LAMP TEST]

Used to test each indicator on the front panel of the SX-2000SM. All Mode and Fault indicators (4) – (9) remain lit and the buzzer sounds as long as this key is pressed.

13. Power Indicator [POWER] (Blue)

Lights when the power is switched on.

14. RUN Indicator [RUN] (Green)

Normally flashes continuously. Goes off while the general urgency all-call is being made (p. 10-9).

15. Reset Key [RESET]

Pressing this key reactivates the SX-2000SM. The entire system, including the SX-2000AI, SX2100AI, SX-2000AO, and SX-2100AO is reactivated.

Notes

• Reactivating the system stops broadcasts currently in progress.

• Do not keep pressing the key for over 1 second. The unit cannot operate. If the unit operation is suspended, press the Reset key for less than one second again.

16. USB Port [USB]

This port is not used.

17. CF Card Access Indicator [ACCESS] (Green)

Flashes while reading from or writing to a CF card.

Note

Do not remove and reinsert the CF card nor operate the DIP switch (19) while this indicator is flashing.

18. CF Card Slot [CF CARD]

Use this slot to insert the CF card to operate settings data or write log data to the card.

• For settings data operation, see p. 1-4.

• For the method of writing log data, see p. 1-5.

Note

Removing and reinserting the CF card requires DIP switch settings. If the CF card is removed and reinserted without performing correct DIP switch settings, this may cause settings data loss or damage the card.

19. DIP Switch [SETTING]

• Switch 1

Used to read log data (p. 1-5). ON: Allows log data to be written into the CF

card.

OFF: Normally select this position.

• Switch 2

Used to perform CF card access settings

(p. 1-4).

ON: Stops access to the CF card. OFF: Normally select this position.

• Switch 3

Set whether or not to enable online control using the SX-2000 Setting Software. (For details, see the separate Installation Manual, "Installation.")

ON: Disables online writing of settings data

and system reset.

OFF: Normally select this position.

• Switch 4

Set the method of operation to reset the failure information (the buzzer and fault indicators) with the FAULT RESET key (11). (For details, see the separate Installation Manual, "Installation.") In the same manner as the FAULT RESET key operation, the failure information can also be reset by shorting the RES terminals of the Data input terminals (26) at the timing set here.

ON: Sets to the accidental operation

prevention mode.

OFF: Sets to the one touch mode.

(For the operation methods in each individual mode, see the separate Installation Manual, "Installation.")

• Switches 5 – 8

These switches are not used.

Note

Switches 1 – 8 are set to the OFF position by default.

1-4

Chapter 1: SX-2000SM SYSTEM MANAGER

2. OPERATING SETTINGS DATA

(DIP Switch 2 Operation)

2.1. Using Settings Data

The SX-2000 system is operated by storing the data set using the SX-2000 Setting Software on a CF card and inserting the card into the SX-2000SM.

Note: Be sure to insert the CF card containing the settings data into the CF card slot.

2.2. Inserting a CF Card

The DIP switch must be set when inserting the CF card into the SX-2000SM. Follow the procedure below:

Note: Do not operate the DIP switch while the CF card access indicator inside the protective cover is flashing.

Step 1. Remove the protective cover on the SX-2000SM's front panel by unscrewing it with a Phillips

screwdriver.

Step 2. Confirm that the CF card access indicator is unlit.

Step 3. Set DIP switch 2 to ON.

Note

DIP switch 2 is set to the OFF position by default.

Step 4. Insert the CF card containing the settings data into the CF card

slot. Then, the buzzer sounds. Setting DIP switch 2 to OFF in Step 5 stops the buzzer.

Step 5. Set DIP switch 2 to OFF.

Step 6. Press the Reset key.

The SX-2000 system is reactivated.

Note

Reactivating the system stops broadcasts currently in progress.

Step 7. Replace the protective cover.

CF card slot

Inside of the protective cover

Protective cover

Screw

CF card access indicatorReset key DIP switch

12345678

1-5

Chapter 1: SX-2000SM SYSTEM MANAGER

3. OUTPUTTING LOG DATA

(Operating DIP Switches 1 and 2)

By writing the SX-2000 system's log data to a CF card in the ".s2l" file format and displaying this data on a PC installed with the SX-2000 Setting Software, the data can be output as an Excel CSV file. The log data includes 2 types of data: Operation log data that contains all logs and Failure log data that contains only failure logs. Both data are saved to a CF card with a file name "Sx2kOp**.s2l" for the Operation log data and "Sx2kFa**.s2l" for the Failure log data. ("**" represents a number from 00 to 99 indicating the order in which the logs have been saved. If more than 100 files are saved, the oldest files are overwritten in chronological order.) The newness or oldness of a file may be ascertained by checking its date. Shown below is the procedure for writing the SX-2000SM's log data to the CF card.

Notes

• When storing log data on a CF card, confirm in advance that it has at least 15 megabytes of free space.

• Do not operate the DIP switch while the CF card access indicator inside the protective cover is flashing.

• Reactivating the SX-2000SM erases the log data temporarily stored in SX-2000SM memory. So, when storing log data on a CF card, be sure to perform that before reactivating the SX-2000SM.

• The SX-2000SM operates on the current setting data until restarted even if the CF card has been removed from the SX-2000SM for reading log data.

Step 1. Remove the protective cover on the SX-2000SM's front panel by unscrewing it with a Phillips

screwdriver.

Step 2. Set DIP switch 1 to ON.

Log data is saved to the CF card at this time.

Step 3. Confirm that the CF card access indicator has gone off, then

set DIP switch 1 to the OFF position.

Step 4. Set DIP switch 2 to ON.

Access to the CF card stops, allowing the card to be removed.

Note: DIP switch 1 is set to OFF

by default.

Inside of the protective cover

Protective cover

Screw

CF card access indicatorReset key DIP switch

CF card slot

12345678

Step 5. Remove the CF card from the card slot.

Step 6. Insert the CF card into the PC's card slot and start the SX-2000 Setting Software.

Confirm the log data using the SX-2000 Setting Software. For details, see the separate Setting Software Instructions, "Utility."

Step 7. Insert the CF card with the saved settings data into the SX-2000SM's CF card slot.

Inserting the CF card causes the buzzer to sound. Setting DIP switch 2 to OFF in Step 8 stops the buzzer.

Step 8. Set DIP switch 2 to OFF.

The CF card can be inserted.

Note

When changing the setting data, be sure to press the Reset key to restart the SX-2000 system after turning off DIP switch 2. Reactivating the system stops broadcasts currently in progress.

Step 9. Replace the protective cover.

1-6

Chapter 1: SX-2000SM SYSTEM MANAGER

12345678

Chapter 2

SX-2000AI AUDIO INPUT UNIT

The SX-2000AI is an audio input unit for use with the SX-2000 system. It features modular construction that allows it to handle from 2 to 8 inputs per unit. It can be mounted in an EIA equipment rack (2U size*), and multiple units can be installed in different locations with no need to centralize in one location. The SX-2000AI transmits audio signals to the SX-2000AO or SX-2100AO Audio Output Units by means of digital transmission in normal operating condition. However, if no general broadcasts can be made due to system failures, the SX-2000AI uses an analog transmission path to transmit audio signals, enabling all-zone calls to be made (referred to as "general urgency all-call" in this manual). The SX-2000AI is equipped with 2 power inputs, allowing the connection of a backup power supply for use during power failures. Level meters provided for each input channel allow monitoring of audio input levels. Input volumes can be adjusted using the input volume controls on the front panel, however the maximum volume when the volume control knob is rotated fully clockwise is a default value defined by the SX-2000 Setting Software. Also, any input channel can be monitored using the internal speaker. The key lock function, designed to prevent accidental mistaken operation, can disable input volume control and channel key settings.

* 1U size = 44.5 mm (standard size)

2-2

Chapter 2: SX-2000AI AUDIO INPUT UNIT

1. NOMENCLATURE AND FUNCTIONS

[Front]

1. Monitor Speaker

Allows any input channel to be monitored.

2. Function Keys [F1, F2, F3, F4]

Pressing a function key executes the function that has been assigned to that key using the SX-2000 Setting Software. (See the separate Setting Software Instructions, "Event Settings.")

3. Fluorescent Display

The default display shows device numbers and firmware versions.

Displays the SX-2000AI's current operation status, input level, etc. (See p. 2-4.)

4. Menu Key [MENU]

Pressing this key displays the fluorescent display's menu screen. Whenever this key is pressed, the screen returns to the default display for whatever portion of the menu screen is displayed.

5. Cancel Key [ /CANCEL]

Used to switch the menu screen.

6. Minus Key [–]

Used to switch the menu screen. When the Monitor ON/OFF Key (15) is set to ON, use this key to select which channel to monitor. The selected channel number decreases by one each time this key is pressed.

7. Plus Key [+]

Used to switch the menu screen. When the Monitor ON/OFF Key (15) is set to ON, use this key to select which channel to monitor. The selected channel number increases by one each time this key is pressed.

8. OK Key [OK/ ]

Used to switch the menu screen.

9. Power Indicator [POWER] (Blue)

Lights when the power is switched on.

10. CPU OFF Indicator [CPU OFF] (Red)

Lights while the general urgency all-call (CPU OFF state) is being made (p. 10-9).

1 2 3 114 5 6 7 8 9 10

12 13 14 15

Protective cover

Inside of the protective cover

16 18 1917

Device No.

AI– 1 VER300

Firmware version

2-3

Chapter 2: SX-2000AI AUDIO INPUT UNIT

11. Standby Indicator [STANDBY] (Green)

Lights while the unit is being initialized at poweron or at reset. Flashes when the fluorescent display is in light shutoff mode and the light stays unlit. Lights when the SX-2000 system is operating on the backup power supply during power failures.

12. Input Volume Controls [INPUT 1 – 8]

Adjust the input volume of each input channel. Rotating the control fully counterclockwise mutes the input sound source connected to that channel and causes the input ON/OFF indicator (28) on the fluorescent display to turn off. When an input channel's "Type" is set to "Emergency" on the SX-2000 Setting software, the input signal source is made to bypass this Input volume control. (See the separate Setting Software Instructions, "System Settings.")

13. Channel Keys [ON/OFF]

Turn each input channel on or off. The input channel alternates between on and off each time this key is pressed. Other functions can also be assigned to each key by using the SX-2000 Setting Software. (See the separate Setting Software Instructions, "Event Settings.") When an input channel's "Type" is set to "Emergency" on the SX-2000 Setting software, the input signal source is made to bypass this Channel key. (See the separate Setting Software Instructions, "System Settings.")

14. Monitor Volume Control [MONITOR]

Adjusts the sound volume of the monitor speaker (1).

15. Monitor ON/OFF Key [ON/OFF]

Enables or disables the audio monitor function for the selected input channel. The monitor function alternates between on and off each time this key is pressed.

16. USB Port [USB]

This port is not used.

17. RUN Indicator [RUN] (Green)

Normally flashes continuously.

18. ID Switch [ID NUMBER]

Sets the SX-2000AI's device number. (See the separate Installation Manual, "Installation.")

19. Reset Key [RESET]

Pressing this key resets the SX-2000AI.

Notes

• Resetting the SX-2000AI stops broadcasts in a part of or all zones currently in progress via the reset SX-2000AI.

• Do not keep pressing the key for over 1 second. The unit cannot operate. If the unit operation is suspended, press the Reset key for less than one second again.

20. DIP Switch [SETTING]

Performs key lock function settings. (See p. 2-6.)

• Switch 1 ON: Disables operation of the front panel input

volume controls and channel keys.

OFF: Cancels key lock status.

• Switches 2 – 8 These switches are not used.

Note

Switches 1 – 8 are set to the OFF position by default.

2-4

Chapter 2: SX-2000AI AUDIO INPUT UNIT

[Fluorescent Display]

21. Text Display Area

Displays the menu screen information when the corresponding function key is pressed.

22. COM Indicator [COM]

Flashes to indicate a communications error.

23. Fault Indicator [FAULT]

Flashes when a system failure, incorrect system configuration* or communications error is detected. This indicator continues to flash until failure conditions return to normal.

* When the system or module configuration

differs from the contents set by the SX-2000 Setting Software.

24. Input Level Meter Fader Indicator [FADER]

Lights when the input level meter indicates the sound volume set using the SX-2000 Setting Software or input volume control.

25. Input Level Meter Level Indicator [LEVEL]

Lights when the input level meter indicates the level being input to the SX-2000AI.

26. Input Level Meter Scale

27. Input Indicator

The input channel to be monitored lights red.

28. Input ON/OFF Indicator

Indicates the unit's operating status when the corresponding channel key is pressed. The indicator state differs depending on the function assigned to each channel key as follows.

* The indicator state is "Unlit" when the input volume is muted.

29. Input Level Meter

Indicates the actual level or a set volume value on each input channel.

30. Key Lock Indicator [KEY LOCK]

Lights when the input volume controls and channel keys are all locked. (See p. 2-6, "Key

Lock Settings and Cancellation.")

31. Emergency Indicator [EMERGENCY]

Lights when the SX-2000 system is in an emergency condition.

32. Remote Microphone Output Status Indicator

Lights red continuously as long as announcements are made from the

RM-200SF, RM-200SA, or

RM-210 Remote Microphone.

Notes

• A timer-activated light shutoff function can be set for the fluorescent display using the SX-2000 Setting Software. (See the separate Setting Software Instructions, "Basic Settings.") When the light shutoff function has been set, if the SX-2000AI is not operated for 5 minutes or more, the fluorescent display's light goes off and the standby indicator (11) begins to flash. Pressing any keys other than the function keys on the front panel resets the screen display.

• Normally, the fluorescent display's light goes off at the time of the power failure.

• While the SX-2000 system is in an emergency condition, the fluorescent display's light does not go off even if the power fails.

Function assigned to the channel key When ON When OFF

Input ON/OFF Lights* Unlit

General-purpose pattern broadcast's Flashes Lights activation and termination

COM FAULT

FADER

LEVEL LEVEL

–10 –20 –30 –40

22 23 26

12 345678

2924 25

KEYLOCK

EMERGENCY

12 34 56 78

34 35

32 33

–10 –20 –30 –40

2-5

Chapter 2: SX-2000AI AUDIO INPUT UNIT

33. Remote Microphone Connection Status

Indicator

The device number of the Remote Microphone connected to the SX-2000AI lights.

34. Monitor Level Meter

Indicates the sound volume level of the input channel being monitored.

35. Monitor Level Meter Scale

Lights when the Monitor ON/OFF Key (15) is set to ON.

36. Monitor ON/OFF indicator [LEVEL]

Lights when the Monitor ON/OFF Key (15) is set to ON.

2-6

Chapter 2: SX-2000AI AUDIO INPUT UNIT

2. KEY LOCK SETTINGS AND CANCELLATION

(DIP Switch 1 Operation)

It is possible to disable the input volume controls, and channel keys in order to prevent mistaken operation. The input volume level set while the key lock function is used takes effect after the key lock has been released.

Note

When the SX-2000 system is placed in an emergency condition during key lock OFF, the emergency sound level preset with the front-mounted volume control knob is invalid, but that defined by the SX-2000 Setting Software is valid. During key lock ON, however, the volume level set with the input volume control knob is valid even if the SX2000 system is placed in an emergency condition. Before setting key lock function to ON, be sure to adjust the input volume control knob corresponding to the emergency source channel for a proper sound level.

Step 1. Remove the protective cover on the SX-2000AI's front panel by unscrewing it with a Phillips

screwdriver.

Step 2. Set the switches.

2-1. If setting a key lock function:

Set DIP switch 1 to ON. When keys have been locked, the KEY LOCK indicator in the fluorescent display lights.

2-2. If canceling a key lock function:

Set DIP switch 1 to OFF. When key locking has been cancelled, the KEY LOCK indicator in the fluorescent display goes off.

Step 3. Replace the protective cover.

Note: DIP switch 1 is set to OFF

by default.

Controls and Keys that can be locked

Inside of the protective cover

Protective cover

Screw

DIP switch

12345678

2-7

Chapter 2: SX-2000AI AUDIO INPUT UNIT

3. OPERATING THE MENU SCREEN

Setting values can be confirmed or changed from the SX-2000AI's front panel.

3.1. Menu Screen Operation Keys

Fluorescent display

SLOT1A 2 D 3 C 4

Red characters indicate changeable display items. One example of these is shown in the hierarchical chart on the next page.

Menu screen operation keys

....

–

This mark is displayed when a selected item has sub-menus available.

OK Key

Moves the display one level down in the hierarchy.

Plus Key

Moves to the next item in the same hierarchy level.

Minus Key

Moves to the previous item in the same hierarchy level.

Cancel Key

Moves the display one level up in the hierarchy.

Menu Key

Pressing this key when default indications are displayed displays the fluorescent display's menu screen. Whenever this key is pressed, the screen returns to the default display for whatever portion of the menu screen is displayed.

2-8

Chapter 2: SX-2000AI AUDIO INPUT UNIT

3.2. Menu Screen Hierarchical Chart

2-9

Chapter 2: SX-2000AI AUDIO INPUT UNIT

3.3. Explanations of Menu Screen Items

3.3.1. Information Display (AI1)

Display screen for menu item "Information."

[Error Display (AI2) ]

When any of the Fault indicators on the SX-2000SM's front panel is flashing, or when the Fault indicator or COM indicator on the SX-2000AI's fluorescent display is flashing, a brief error message appears in the text display area as shown below.

No abnormality or failure is detected. (Fault and COM indicators: Off)

Incorrect system configuration* is detected. (Fault indicator: Flashing)

* When the system or module configuration differs from the

contents set by the SX-2000 Setting Software.

System failure is detected. (e.g. The RM-200SA's microphone has failed.) (Fault indicator: Flashing)

Communications error* is detected. (Fault and COM indicators: Flashing)

* The SX-2000AI cannot communicate with the SX-2000SM.

Note

Contents of failure or abnormality can be confirmed by using the log data stored in the SX-2000SM. (See p. 1-5.)

1– INFORMAT ION

FAULTLESS

COMPONE NT

FAULT

DET E CT E D

SX L I NK C

REROR

OM F AU L T

2-10

Chapter 2: SX-2000AI AUDIO INPUT UNIT

3.3.2. Operation Status Display (AI3)

Display screen for menu item "Operation Status."

[BGM Pattern Display (AI4)]

Displays the pattern number for a BGM broadcast in progress.

When this screen is displayed, the Input ON/OFF indicator on the fluorescent display is as follows:

2–OPERAT ION STATUS

BGM

PATTERN No 1

Indicates the unit's operating status when the corresponding function keys (F1 to F4) are pressed. The indicator state differs depending on the function assigned to each function key as follows.

Function assigned to the function key

Change or end the BGM pattern

Unlit:

Lights:

When the BGM pattern assigned to the function key is not being broadcast When the BGM pattern assigned to the function key is being broadcast

General-purpose broadcast pattern

Unlit: Flashes:

When the function key is OFF When the function key is ON

Display

COM FAULT

FADER

LEVEL LEVEL

12 345678

0 –10 –20 –30 –40

KEYLOCK

EMERGENCY

12 34 56 78

–10 –20 –30 –40

2-11

Chapter 2: SX-2000AI AUDIO INPUT UNIT

[Volume Setting Display (AI5), Volume Setting Detail Display (AI6)]

Indicates the input volume level set using the SX-2000 Setting Software in the input level meter. Besides, on the Volume Setting Detail Display screen, the set value for each input channel can be confirmed. Pressing the plus key increases the channel number by one and displays the setting value for that channel. Pressing the minus key decreases the channel number by one and displays the setting value for that channel.

When these screens are displayed, the entire fluorescent display is as follows:

OK /

CONF IG VOLUME

VOLUME Ch1 –20dB

/CANCEL

The indicator of the channel selected for monitoring lights. When the input volume control is operated, the corresponding channel indicator lights.

Lights when the input status is on, and goes off when the input

turns off. However, when the input volume is muted, this indicator goes off. Also, when the input volume control or channel ON/OFF is operated, the indicator of the corresponding channel lights.

Lights

COM FAULT

FADER

LEVEL LEVEL

12 345678

0 –10 –20 –30 –40

Lights

Indicates the levels set using the SX-2000 Setting Software.

KEYLOCK

EMERGENCY

12 34 56 78

–10 –20 –30 –40

2-12

Chapter 2: SX-2000AI AUDIO INPUT UNIT

[Front Panel Volume Display (AI7), Front Panel Volume Detail Display (AI8)]

Indicates the input volume level set using the front panel's input volume control in the input level meter. Besides, on the Volume Setting Detail Display screen, the set value for each input channel can be confirmed. Pressing the plus key increases the channel number by one and displays the setting value for that channel. Pressing the minus key decreases the channel number by one and displays the setting value for that channel.

When these screens are displayed, the entire fluorescent display is as follows:

OK /

PANEL VOLUME

VOLUME Ch1 –10dB

/CANCEL

The indicator of the channel selected for monitoring lights. When the input volume control is operated, the corresponding channel indicator lights.

Lights when the input status is on, and goes off when the input

turns off. However, when the input volume is muted, this indicator goes off. Also, when the input volume control or channel ON/OFF is operated, the indicator of the corresponding channel lights.

Lights

COM FAULT

FADER

LEVEL LEVEL

12 345678

0 –10 –20 –30 –40

Lights

Indicates the levels set using the Input volume controls.

KEYLOCK

EMERGENCY

12 34 56 78

–10 –20 –30 –40

2-13

Chapter 2: SX-2000AI AUDIO INPUT UNIT

[Bus Selection Menu Display (AI9), Bus Selection Detail Display (AI10)]

A "bus" is a path through which audio signals pass. The SX-2000 system has 16 bus lines. The Bus Selection Detail Display shows which bus is used to send a broadcast in progress and which output of the SX-2000AO/2100AO it is sent to. If there are two or more output destinations, only the smallest output channel number is shown first, and this can be switched over to other output destinations by pressing the OK key. Pressing the plus key increases the input channel number by one and displays the broadcast status for that channel. Pressing the minus key decreases the input channel number by one and displays the broadcast status for that channel.

Regarding the type of broadcast, "B" is displayed for BGM broadcasts, and "P" is displayed for generalpurpose broadcasts or emergency broadcasts. For input channels not making broadcasts, the indication "– – –" is displayed for bus No., for the SX-2000AO/2100AO's device No., for the SX-2000AO/2100AO's output channel, and for the type of broadcast.

When these screens are displayed, the entire fluorescent display is as follows:

SX-2000AO/2100AO’s

Type of broadcast

device No.

OK /

BUS SELECT STATUS

/CANCEL

IN1 B 3 AO16– 4B

SX-2000AI’s input channel

Bus No. SX-2000AO/2100AO’s

output channel

The indicator of the channel selected for monitoring lights. When the input volume control is operated, the corresponding channel indicator lights.

Indicates the unit's operating status when the corresponding channel key is pressed. The indicator state differs depending on the function assigned to each channel key as follows.

Function assigned to the channel key

Input ON/OFF Unlit:

Lights:

When the input channel is OFF When the input channel is ON (The indicator state is "Unlit" when the input volume is muted.) When operating the corresponding input volume control or channel key

General-purpose broadcast pattern

Lights: Flashes:

When the channel key is OFF When the channel key is ON

These indicators light when the Monitor ON/OFF key is set to ON.

COM FAULT

FADER

LEVEL LEVEL

12 345678

0 –10 –20 –30 –40

KEYLOCK

EMERGENCY

Display

12 34 56 78

–10 –20 –30 –40

Lights

Indicates the level being input to the SX-2000AI.

When the Monitor ON/OFF key is set to ON, this meter shows the signal level of the input channel being monitored.

2-14

Chapter 2: SX-2000AI AUDIO INPUT UNIT

[Equipment Version Display (AI16)]

Displays the SX-2000AI's firmware version.

3.3.3. Equipment Information Display (AI11)

Display screen for menu item "Equipment Information."

[MAC Address Menu Display (AI12), MAC Address Display (AI13)]

Displays the MAC address* set to the SX-2000AI on the Mac Address Display screen.

* A 12-digit hexadecimal address inherently assigned to and unique to a networking device.

[Slot Status Display (AI14), Slot Status Detail Display (AI15)]

Displays which module is installed in the SX-2000AI's rear panel slots 1 – 4. Alphabets A – D represent module model numbers as shown below.

A: D-921F and D-921E B: D-922F and D-922E C: D-936R D: SX-200RM –: Module is not installed.

The Slot Status Detail Display shows which module is installed in the SX-2000AI's rear panel slots 1 – 4 using a model number for each slot. Slots with no installed module are displayed as "BLANK." Pressing the plus key increases the slot number by one and displays information for that slot number. Pressing the minus key decreases the slot number by one and displays information for that slot number.

3–UNIT STATUS

OK /

AC ADDRESS

/CANCEL

00– 05– F9– FF– 85– 3E

Characters that represent module model numbers.

OK /

SLOT1A 2 D 3 C 4

....

Slot number

–

/CANCEL

SLOT 1D–921 E/F ( A )

Represents the module model number.

UN I T VER

_ 00_ 000

2-15

Chapter 2: SX-2000AI AUDIO INPUT UNIT

[Sub CPU Version Display (AI17) ]

Displays the version of software related to operations and displays on the SX-2000AI's front panel.

[Hardware Version Display (AI19), Hardware Version Detail Display (AI20)]

Displays the hardware version for each circuit board comprising the SX-2000AI unit. In the screens of Hardware Version Detail Display, pressing the plus or minus key advances or reverses the screen.

PCB CPU: Displays the CPU circuit board

version.

PCB FRONT: Displays the front circuit board

version.

PCB POWER: Displays the power supply circuit

board version.

PCB MOTHER: Displays the motherboard version.

PCB ANALOG: Displays the analog circuit board

version.

[SX-2000SM Version Display (AI18) ]

Displays SX-2000SM firmware version. It appears when the communication with the SX-2000SM is complete. Before that, "Ver.–.– –" is displayed on the version display section.

SUB CPU VER 1

X–2000S

VER 300

OK /

VER SX–2000 AI

.. .

PCB CPU VE R 0

/CANCEL

PCB FRONT VE R 0

PCB POWER VE R 0

PCB MOTHER VE R 0

PCB ANALOG VE R 0

Chapter 3

SX-2100AI AUDIO INPUT UNIT

The SX-2100AI is an audio input unit for use with the SX-2000 system. It features modular construction that allows it to handle from 2 to 8 inputs per unit. It is equipped with 16 control inputs and 16 control outputs. It can be mounted in an EIA equipment rack (2U size*), and multiple units can be installed in different locations with no need to centralize in one location. The SX-2100AI transmits audio signals to the SX-2000AO or SX-2100AO Audio Output Units by means of digital transmission in normal operating condition. However, if no general broadcasts can be made due to system failures, the SX-2100AI uses an analog transmission path to transmit audio signals, enabling all-zone calls to be made (referred to as "general urgency all-call" in this manual). The SX-2100AI is equipped with 2 power inputs, allowing the connection of a backup power supply for use during power failures. Level meters provided for each input channel allow monitoring of audio input levels. Input volumes can be adjusted using the input volume controls on the front panel, however the maximum volume when the volume control knob is rotated fully clockwise is a default value defined by the SX-2000 Setting Software. Also, any input channel can be monitored using the internal speaker. The key lock function, designed to prevent accidental mistaken operation, can disable input volume control and channel key settings.

* 1U size = 44.5 mm (standard size)

1. Monitor Speaker

Allows any input channel to be monitored.

2. Function Keys [F1, F2, F3, F4]

Pressing a function key executes the function that has been assigned to that key using the SX-2000 Setting Software. (See the separate Setting Software Instructions, "Event Settings.")

3. Fluorescent Display

The default display shows device numbers and firmware versions.

Displays the SX-2100AI's current operation status, input level, etc. (See p. 3-4.)

4. Menu Key [MENU]

Pressing this key displays the fluorescent display's menu screen. Whenever this key is pressed, the screen returns to the default display for whatever portion of the menu screen is displayed.

5. Cancel Key [ /CANCEL]

Used to switch the menu screen.

6. Minus Key [–]

7. Plus Key [+]

8. OK Key [OK/ ]

Used to switch the menu screen.

9. Power Indicator [POWER] (Blue)

Lights when the power is switched on.

10. CPU OFF Indicator [CPU OFF] (Red)

Lights while the general urgency all-call (CPU OFF state) is being made (p. 10-9).

3-2

Chapter 3: SX-2100AI AUDIO INPUT UNIT

1. NOMENCLATURE AND FUNCTIONS

[Front]

1 2 3 114 5 6 7 8 9 10

12 13 14 15

Protective cover

Inside of the protective cover

16 18 1917

Device No.

AI– 1 VER300

Firmware version

3-3

Chapter 3: SX-2100AI AUDIO INPUT UNIT

11. Standby Indicator [STANDBY] (Green)

12. Input Volume Controls [INPUT 1 – 8]

13. Channel Keys [ON/OFF]

14. Monitor Volume Control [MONITOR]

Adjusts the sound volume of the monitor speaker (1).

15. Monitor ON/OFF Key [ON/OFF]

Enables or disables the audio monitor function for the selected input channel. The monitor function alternates between on and off each time this key is pressed.

16. USB Port [USB]

This port is not used.

17. RUN Indicator [RUN] (Green)

Normally flashes continuously.

18. ID Switch [ID NUMBER]

Sets the SX-2100AI's device number. (See the separate Installation Manual, "Installation.")

19. Reset Key [RESET]

Pressing this key resets the SX-2100AI.

Notes

• Resetting the SX-2100AI stops broadcasts in a part of or all zones currently in progress via the reset SX-2100AI.

• Do not keep pressing the key for over 1 second. The unit cannot operate. If the unit operation is suspended, press the Reset key for less than one second again.

20. DIP Switch [SETTING]

Performs key lock function settings. (See p. 3-6.)

• Switch 1 ON: Disables operation of the front panel input

volume controls and channel keys.

OFF: Cancels key lock status.

• Switches 2 – 8 These switches are not used.

Note

Switches 1 – 8 are set to the OFF position by default.

3-4

Chapter 3: SX-2100AI AUDIO INPUT UNIT

[Fluorescent Display]

21. Text Display Area

Displays the menu screen information when the corresponding function key is pressed.

22. COM Indicator [COM]

Flashes to indicate a communications error.

23. Fault Indicator [FAULT]

Flashes when a system failure, incorrect system configuration* or communications error is detected. This indicator continues to flash until failure conditions return to normal.

* When the system or module configuration

differs from the contents set by the SX-2000 Setting Software.

24. Input Level Meter Fader Indicator [FADER]

Lights when the input level meter indicates the sound volume set using the SX-2000 Setting Software or input volume control.

25. Input Level Meter Level Indicator [LEVEL]

Lights when the input level meter indicates the level being input to the SX-2100AI.

26. Input Level Meter Scale

27. Input Indicator

The input channel to be monitored lights red.

28. Input ON/OFF Indicator

Indicates the unit's operating status when the corresponding channel key is pressed. The indicator state differs depending on the function assigned to each channel key as follows.

* The indicator state is "Unlit" when the input volume is muted.

29. Input Level Meter

Indicates the actual level or a set volume value on each input channel.

30. Key Lock Indicator [KEY LOCK]

Lights when the input volume controls and channel keys are all locked. (See p. 3-6, "Key

Lock Settings and Cancellation.")

31. Emergency Indicator [EMERGENCY]

Lights when the SX-2000 system is in an emergency condition.

32. Remote Microphone Output Status Indicator

Lights red continuously as long as announcements are made from the RM-200SF, RM-200SA, or RM-210 Remote Microphone.

Notes

• A timer-activated light shutoff function can be set for the fluorescent display using the SX-2000 Setting Software. (See the separate Setting Software Instructions, "Basic Settings.") When the light shutoff function has been set, if the SX-2100AI is not operated for 5 minutes or more, the fluorescent display's light goes off and the standby indicator (11) begins to flash. Pressing any keys other than the function keys on the front panel resets the screen display.

• Normally, the fluorescent display's light goes off at the time of the power failure.

• While the SX-2000 system is in an emergency condition, the fluorescent display's light does not go off even if the power fails.

Function assigned to the channel key When ON When OFF

Input ON/OFF Lights* Unlit

General-purpose pattern broadcast's Flashes Lights activation and termination

COM FAULT

FADER

LEVEL LEVEL

22 23 26 2924 25

12 345678

0 –10 –20 –30 –40

KEYLOCK

EMERGENCY

12 34 56 78

34 35

–10 –20 –30 –40

3-5

Chapter 3: SX-2100AI AUDIO INPUT UNIT

33. Remote Microphone Connection Status Indicator

The device number of the Remote Microphone connected to the SX-2100AI lights.

34. Monitor Level Meter

Indicates the sound volume level of the input channel being monitored.

35. Monitor Level Meter Scale

Lights when the Monitor ON/OFF Key (15) is set to ON.

36. Monitor ON/OFF Indicator [LEVEL]

Lights when the Monitor ON/OFF Key (15) is set to ON.

+ 102 hidden pages