Toa ST-322B User Manual

INSTRUCTION MANUAL

MICROPHONE STANDS

hread adapter..............................................1

Cable clamp (large)........................................1

Cable clamp (small, ST-321B only)................1

3. INSTALLATION

Step 1.

Spread the tripod legs.

(1)

Set up the stand on the floor with its legs down.

(2)

Turn the base fixing screw counterclockwise to loosen.

(3)

Slide the outer pipe up until it touches the base.

(4)

Turn the base fixing screw clockwise to tighten.

(5)

Spread the tripod legs as far as they will open.

Step 2.

Attach the microphone holder.

These microphone stands are compatible with 2 types

of screw threads.

If the microphone holder to use cannot be mounted to

the s tand (or boom a r m ) with the thr e a d adapter

preinstalled, unscrew the thread adapter and mount the

microphone holder directly to the stand (or boom arm).

Note

Some microphone holders are not compatible with this

thread adapter.

Step 3.

Adjust the stand height.

(1)

Turn the height adjustment grip counterclockwise to

loosen.

(2)

Slide the inner pipe up or down to the desired height.

(3)

Turn the height adjustment grip clockwise to tighten.

Step 4.

Adjust the boom arm. (ST-321B only)

[Angle adjustment]

(1)

Turn the boom angle adjustment screw

counterclockwise

to loosen.

(2)

Adjust the boom arm to the desired angle.

(3)

Turn the boom angle adjustment screw clockwise to

tighten.

[Boom length adjustment]

(4)

Turn the boom length adjustment screw

counterclockwise

to loosen.

(5)

Adjust the boom arm to the desired length.

(6)

Turn the boom length adjustment screw clockwise to

tighten.

Step 5.

Secure the microphone cable.

Remove the cable clamp from the outer pipe, clamp the

microphone cable, then replace the removed cable

clamp.

Note

One each of large and small cable clamps is provided

for the ST-321B.

Use the large one for the outer pipe and the small one

for the boom arm.

2. SPECIFICATIONS

1045 – 1705 mm (3.43 – 5.6 ft) 971 – 1627 mm (3.19 – 5.34 ft)

53 – 660 mm (2.09" – 25.98") Without boom arm

NS 5/8 (Stand or boom arm), U 5/16 (Thread adapter)

Steel tube for general structual purpose, black, mat, paint

2.9 kg (6.39 lb) 2.2 kg (4.85 lb)

Model No.

Height

Boom Length

Screw Thread

Finish

Weight

Thank you for purchasing TOA Microphone Stand.

Please carefully follow the instructions in this manual to ensure long,

trouble-free use of your equipment.

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the instructions in

this section for correct and safe operation.

• Be sure to follow all the precautionary instructions in this section, which

contain important warnings and/or cautions regarding safety.

• After reading, keep this manual handy for future reference.

• Avoid installing the unit in unstable locations, such as on a rickety table

or a slanted surface. Doing so may result in the unit falling down and

causing personal injury and/or property damage.

• Ensure that all screws are securely tightened. If they are not tightened

or firmly secured after installation, the unit could fall down, possibly

resulting in personal injury.

• When using the unit outside under strong wind, take appropriate

measures to prevent it from falling down. If it falls down, this may

cause personal injury and/or property damage.

• Avoid placing the unit in a doorway or other high traffic area as people

may trip on the unit and cord, or be injured by falling objects.

• Spread the tripod legs to the maximum. Doing otherwise may cause

the unit to fall down or off, resulting in personal injury.

CAUTION

Indicates a potentially hazardous situation which, if mishandled,

could result in moderate or minor personal injury, and/or property

damage.

133-35-457-80

URL: http://www.toa.jp/

ST-321B

ST-322B

• Accessories

Note: The design and specifications are subject to change without notice for improvement.

The figure shows the ST-321B.

Base fixing screw

Base

Microphone cable

Outer pipe

Cable clamp (large)

Boom arm (ST-321B only)

Cable clamp (small)

Height adjustment grip

Boom angle

adjustment screw

Inner pipe

Boom length adjustment screw

Thread adapter

(NS 5/8)

Stand or Boom arm

(U 5/16)

Thread adapter

Microphone holder (option)