Toa ST-16A User Manual

ST-16ASPEAKER STAND

INSTRUCTION MANUAL

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe
operation.

• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.

• After reading, keep this manual handy for future reference.

2. HOW TO USE

Step 1. Attach the bracket to the speaker as shown below.

Attach the bracket to the speaker

Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.

WARNING

• Do not mount the speaker of 7 kg or more. The stand or its internal pipe may fall down or drop, resulting in
personal injury. Even though the speaker weight is below 7 kg, do not use that speaker if the stand is made
unstable.

• Do not extend the internal pipe beyond the MAXIMUM point marked in red. Doing so may make the stand
unstable, and cause the stand or its internal pipe to fall down or drop, resulting in personal injury.

• Avoid installing the stand in the following locations. Otherwise, the mounted speaker may drop or the stand
may fall, resulting in personal injury.

· Doorway or other high traffic area where people may trip on the stand.

· Locations where the unit is exposed to a strong wind.

· Unstable locations, such as on a rickety table or a slanted surface.
Important: Even in locations other than the above, if the unit may fall down, take appropriate fall preventive

measures.

• When adjusting the stand height with the speaker mounted, hold the speaker firmly. Doing otherwise may
cause the stand to fall, resulting in personal injury and/or property damage.

• Fully expand the legs. If the legs are not fully expanded, the stand may fall down, resulting in personal injury.

Attachment to the horn speaker Attachment to the megaphone Attachment to the FGM speaker

Butterfly nut

Spacer

Be sure to use the spacer.

If not used, the thread in the
megaphone may be destroyed.

Washer

Bracket

Hexagon bolt

Insert the hexagon bolt into the hexagonal
hole located inside the bracket and tighten
the bolt to attach the bracket.

Bracket

Hexagon bolt

Insert the hexagon bolt into the hexagonal hole
located inside the bracket and tighten the bolt
rotating the bracket in the direction of the arrow
to secure the bracket.

Note

Do not use this spacer for the
megaphones ER-2230W and
WR-2930W.

Bracket

Speaker
mounting screw

Step 2. Loosen the leg locking knob to fully expand the legs. Lowering the slide leg adjustment till it hits the

stopper in the center of the external pipe permits maximum leg expansion.

Step 3. Tighten the leg locking knob to secure the legs.

Step 4. Loosen the internal pipe locking knob to raise the internal pipe to the desired height.

Step 5. Tighten the internal pipe locking knob to secure the pipe.

Step 6. Insert the bracket onto the top of the internal pipe, and mount the speaker on the stand.

Step 7. After determining the orientation of the speaker, secure the speaker by tightening the bracket fixing

knob.

Note: After installation completion, ensure again that every knob is tightened.

Step 8. After use, reverse the procedures 1 – 7 above to detach the speaker and fold the stand.

Note: Be sure to fold the stand after detaching the speaker from the stand.

[Storing mounting screws]

Speaker mounting screws for installing the FGM speakers can be stored
by mounting them into the storage holes provided in the bracket.
Use these holes to prevent the loss of screws while putting away the
equipment.

Put away the stand after use

Mount the speaker on the stand

Put up the stand

3. PART NAMES

Stand (when in use)Stand (when folded)Accessory

Speaker mounting
screw

Screw storage hole

Bracket

Speaker mounting screw
(M5 x 20) x 2

Hexagon bolt
(M8 x 20) x 1

Washer x 1

Spacer x 1

Butterfly nut x 1

Slide leg
adjustment

1050 mm

Stay

Bracket

Bracket fixing knob

Internal pipe

Internal pipe
locking knob

Leg locking knob

External pipe

Stopper

Slide leg adjustment

1130 – 1660 mm

Leg

Bracket

Bracket fixing
knob

Internal pipe

Internal pipe
locking knob

External pipe

Leg locking
knob

Stopper

Weight: 1.7 kg (bracket included)

Stay