Toa SR-WB3 User Manual

INSTALLATION MANUAL

WALL MOUNTING BRACKET

SR-WB3

The SR-WB3 is a wall mounting bracket designed to install the Line Array Speaker SR-H2L, SR-H2S, SR-H3L, or SR-H3S flat against the wall.

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the

instructions in this section for correct and safe operation.

• Be sure to follow all the precautionary instructions in this section,

which contain important warnings and/or cautions regarding safety.

• After reading, keep this manual handy for future reference.

3. SPECIFICATIONS

Note: The design and specifications are subject to change without

notice for improvement.

Step 1. Install the Bracket bases to the wall.

(See the diagrams at right.)

Step 2. Attach the Speaker brackets to the

speaker rear. Remove the designated screws, then secure the brackets using these screw holes. The removed screws are not used.

Tip

For a single speaker, attach the brackets at the topmost and lowest positions on the speaker rear. For the linked speakers, attach them to the positions shown in the lower right diagram.

Step 3. Connect the speaker cable to the

removable terminal plug. For connection, refer to the instruction manual enclosed with the speaker.

Step 4. Hook the speaker on the Bracket bases.

Slide down the speaker body so that each Speaker bracket's hook fits in the Bracket base's slit.

Step 5. Fix the uppermost Speaker bracket with

the supplied hex bolt M4 x 15. This prevents the speaker from dropping off. (The same way applies to the linked speakers.)

2. INSTALLATION

• Install the unit only in a location that can structurally support the

total weight of the unit and the speaker. Doing otherwise may result in the unit falling down and causing personal injury and/or property damage.

• Since the unit is designed for in-door use, do not install it

outdoors. If installed outdoors, the aging of parts causes the unit to fall off, resulting in personal injury.

• Do not use other methods than specified to mount the bracket.

Extreme force is applied to the unit and the unit could fall off, possibly resulting in personal injuries.

• Use bolts and nuts that are appropriate for the wall's material

and structure. Failure to do so may cause the speaker to fall, resulting in material damage and possible personal injury.

• Tighten each nut and bolt securely. Ensure that the bracket has

no loose joints after installation to prevent accidents that could result in personal injury.

• Use the unit only with the specified speaker. Doing otherwise

may cause the unit to fall off, resulting in personal injury.

• Do not mount the unit in locations exposed to constant vibration.

The mounting bracket can be damaged by excessive vibration, potentially causing the unit to fall, which could result in personal injury.

Indicates a potentially hazardous situation which, if mishandled, could result in death or serious personal injury.

WARNING

Indicates a potentially hazardous situation which, if mishandled, could result in moderate or minor personal injury, and/or property damage.

CAUTION

• Avoid touching the unit's sharp metal edge to prevent injury.

• Do not stand or sit on, nor hang down from the unit as this may

cause it to fall down or drop, resulting in personal injury and/or property damage.

• Have the unit checked periodically by the shop from where it was

purchased. Failure to do so may result in corrosion or damage to the unit that could cause the unit to fall, possibly causing personal injury.

Applicable Speaker SR-H2L, SR-H2S, SR-H3L, SR-H3S Finish Rolled steel plate, white, paint Weight 220 g (7.76 oz) Component Speaker bracket ... 2, Bracket base ... 2

133-05-445-30

URL: http://www.toa.jp/

• Accessories

Hex bolt M4 x 15 (with washer)

............................ 1

Hex bolt M5 x 25 (with washer)

............................ 4

• Optional product

Extension Plate: SR-EP3

Hex bolt M4 x 15

(supplied with SR-WB3)

Speaker bracket

Hex bolt M5 x 25

(supplied with SR-WB3)

Removable terminal plug

Speaker body (rear)

Remove the attached screw.

Note: This removed screw is not used.

Required number of Bracket bases and their mounting dimensions

Installing one SR-H2L

2 Bracket bases (1 SR-WB3)

16.2

(0.64)

Over 70 (3)

40 (1.57)

588 ±2

2-φ7 (2-φ0.28)

SR-H2L

(23.15 ±0.08)

62 (2.44)

40 (1.57)

[Dimensions of Bracket base]

Unit: mm (inches)

Installing one SR-H2S

2 Bracket bases (1 SR-WB3)

Over 70 (3)

508 ±2

(20 ±0.08)

14.6 (0.57)

49.7

Bracket base

WARNING

Any bolts and nuts used to fix the Bracket base to the wall are not enclosed. Prepare ones appropriate for the wall's material and structure.

Speaker bracket

Hook

Slit

Installing one SR-H3L

2 Bracket bases (1 SR-WB3)

16.2

(0.64)

40 (1.57) 40 (1.57) 40 (1.57)

Over 70 (3)

16.2

(0.64)

Installing one SR-H3S

2 Bracket bases (1 SR-WB3)

Over 70 (3)

SR-H2S

SR-H3L

1020 ±2 (40.16 ±0.08)

(1.96)

1106 ±2 (43.54 ±0.08)

Notes

• Install the Bracket base at least 70 mm (3") away from the ceiling or any object.

• When installing the linked SR-H3L and SR-H2L, one Bracket base remains unused.

To the wall

Bracket base

To the wall

Installing the linked SR-H2L and SR-H3L

3 Bracket bases (2 SR-WB3s)

16.2

(0.64)

Over 70 (3)

SR-H3S

1223 ±2

(48.15 ±0.08)

1775 ±2

(69.88 ±0.08)

Speaker bracket mounting

positions when linking speakers

When linking SR-H2L and SR-H3L

3 Speaker brackets required (2 SR-WB3s required*)

* One Speaker bracket remains unused.

Extension plate

(SR-EP3)

Speaker bracket

SR-H3L

Installing the linked 2 SR-H3Ls

4 Bracket bases (2 SR-WB3s)

16.2

(0.64)

40 (1.57) 40 (1.57)

SR-H2L

554 ±2

(21.81 ±0.08)

Over 70 (3)

16.2

(0.64)

SR-H3L

1741 ± 2

(68.54 ±0.08)

2293 ±2

(90.28 ±0.08)

SR-H3L

When linking 2 SR-H3Ls

4 Speaker brackets required (2 SR-WB3s required)

Speaker bracket

SR-H3L

SR-H2L

Extension plate

(SR-EP3)

SR-H3L

Note: This figure shows the installation example of the SR-H2L.