Toa SP-1100 User Manual
4. SPECIFICATIONS
3.
NOMENCLATURE AND DIMENSIONAL DIAGRAM
INSTRUCTION MANUAL
WALL MOUNTING BRACKET
SP-1100
Thank you for purchasing TOA's Wall Mounting Bracket.
Please carefully follow the instructions in this manual to
ensure long, trouble-free use of your equipment.
Note: The design and specifications are subject to
change without notice for improvement.
• Accessories
4 x 16 tapping screws ................................ 2
• Before installation or use, be sure to carefully read all
the instructions in this section for correct and safe
operation.
• Be sure to follow all the precautionary instructions in
this section, which contain important warnings and/or
cautions regarding safety.
• After reading, keep this manual handy for future
reference.
1. SAFETY PRECAUTIONS
WARNING
Indicates a potentially hazardous situation which,
if mishandled, could result in death or serious
personal injury.
• Install the unit only in a location that can structurally
support the weight of the unit and the mounting bracket.
Doing otherwise may result in the unit falling down and
causing personal injury and/or property damage.
• Avoid mounting the bracket in locations where people
could accidentally bump into it. Failure to observe this
could result in personal injury.
CAUTION
Indicates a potentially hazardous situation which,
if mishandled, could result in moderate or minor
personal injury, and/or property damage.
• Since the unit is designed for indoor use, do not install it
outdoors. If installed outdoors, the aging of parts
causes the unit to fall off, resulting in personal injury.
Also, when it gets wet with rain, there is a danger of
electric shock.
• Use the specified megaphone in combination. Doing
otherwise may cause the unit or component to fall off,
resulting in personal injury.
• Do not stand or sit on, nor hang down from the unit as
this may cause it to fall down or drop, resulting in
personal injury and/or property damage.
2. GENERAL DESCRIPTION
The SP-1100 bracket is designed to be used exclusively
to mount the ER-1203 and ER-1206 series megaphones
on a wall. It permits the megaphone to be installed in
easy-to-see locations, and the megaphone can be easily
mounted and detached. The dustproof cover protects the
megaphone's mouthpiece while the megaphone is placed
in the bracket, offering improved hygienic safety.
Finish Stay: Stainless steel (SUS304)
Holder, dustproof cover: ASA resin,
dark gray clear
Dimensions [With dustproof cover and holder open]
126 (w) x 420 (h) x 156 (d) mm
Weight 410 g
Usable ER-1203,
Megaphone ER-1206, ER-1206S, ER-1206W
[Front] [Side]
420
33
77
126
Dustproof cover
Slotted hole
Stay
Holder
156
[Megaphone mounted view]
282
333
Megaphone
SP-1100
Wall
Unit: mm
Step 1. Install a self-tapping screw temporarily into the
wall.
Notes
• Use the screw that is appropriate for the
construction of the wall.
• Two 4 x 16 self-tapping screws are supplied
with the SP-1100 bracket.
Step 2. Hook the bracket's slotted hole over the screw
head. Slide the bracket down in the direction
indicated by the arrow.
Step 3. Align the bracket vertically, then fix the bottom part
of the bracket with another self-tapping screw.
Step 4. Tighten both the top and bottom screws to
securely mount the bracket to the wall.
5. INSTALLATION
Two mounting pitches are
made available for selection:
192.5 mm or 242.5 mm.
7. FOLDING THE BRACKET
The holder and dustproof cover can fold if the megaphone
is removed.
Fold the holder first, and then the dustproof cover.
When mounting the megaphone, open the dustproof
cover first, and then the holder.
Step 1. Raise the bracket's dustproof cover.
Step 2. Place the megaphone on the holder with its front
down.
Step 3. Lower the dustproof cover of the bracket.
6. MOUNTING THE MEGAPHONE
When detaching the megaphone from the bracket,
reverse the above procedures.
Note: Lift the megaphone to detach. The dustproof
cover opens if the megaphone is lifted.
Printed in Indonesia
533-03-028-80
Slotted hole dimensions
(mm)
5
10
ø10
1
2
Wall
3
4 x 16 self-tappimg screws (supplied)
242.5 mm
192.5 mm
Stay
Dustproof cover
2
SP-1100
1
Holder
3
2
Inner horn
1
Holder
Dustproof cover
SP-1100
Loading...