TOA RS-170, RS-150 Installation Guide

INSTALLATION MANUAL

RS-150, RS-160, RS-170, RS-180SUBSTATION

Thank you for purchasing TOA's Substation. Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.

Note: For operation of the units, refer to the N-8000 series operating instructions.

1. GENERAL DESCRIPTION

TOA's RS-150, RS-160, RS-170, and RS-180 are Substations designed to be used with TOA's N-8000 Series Packet Intercom System.

2. SPECIFICATIONS

Model No. RS-150 RS-160 RS-170 RS-180 Rated Input 1 W Rated Impedance 625 Ω (1 W, 25 V) Internal Speaker 4 cm dynamic type Transmission Range 0.5 km/ø0.5 mm (AWG24)

0.8 km/ø0.65 mm (AWG22)

1.3 km/ø0.9 mm (AWG19)

Control Output (RS-180 only)

Open collector, Control current: 30 mA

(The open collector output is kept turned on till the conversation is finished after the call button was pressed.)

Operating Temperature

(Temperature range not to freeze the speaker and switch)

Finish (Panel) Stainless steel, hairline

(Call button) Resin Metal

(Printed circuit board) (RS-170, RS-180 only) Weather-resistant coating

Dimensions (w) 120 mm

(h) 120 mm (d) 48.5 mm 57.5 mm 58.5 mm

Weight 410 g 540 g 570 g Accessories Machine screw M4 x 25 ... 4, UNC No. 6-32 x 18 ... 4

Applicable Box (For ush-mount) 2-gang electrical box: YC-302 (option)

(For surface-mount) Wall-mount box: YC-822 (option) Wall-mount box: YC-822/YC-823 (option)

Note: The design and specifications are subject to change without notice for improvement.

Withstand voltage:

–10 to +50°C

30 V DC,

3. CONNECTIONS

[Connection to the N-8000RS or N-8010RS (for 25 V line)]

(N-8000RS or N-8010RS)

A B C

Orange

Brown

Black

[Connection to the external relay (RS-180 only)]

RS-180

Blue (HOT)

White (COM)

Diode

Relay

Open collector output: 24 V DC (max.), 30 mA

RS-150/160/170/180

Speaker Call button

Status indicator (RS-180 only)

Open collector output (RS-180 only)

External power supply

24 V DC

GND

Blue (HOT)

White (COM)

Note

Cut out the control cables if they are not used to avoid short-circuiting.

4. MOUNTING

This figure is

[Flush mounting using an electrical box] [Wall surface mounting using the Wall-mount box]

Mount the substation to an electrical box mounted to the wall. Attach the Substation to the YC-822 (Indoor wall-mount

box) or YC-823 (Outdoor wall-mount box)

2-gang electrical box YC-302 (option)

Wall surface

wall.

Note

This figure is

Wall surface

RS-160/170.

RS-150/160/170/180

Note

This figure is RS-160/170.

RS-150/160/170/180

Machine screw M4 x 25 (accessory)

Wall

[Section view]

RS-150/160/170/180

Machine screw M4 x 25 (accessory)

Note

When using the PA paging function, keep the station as far away from the PA paging speaker as possible to avoid acoustic feedback.

Note

In the case of the YC-823, install it facing the ø6 mm weep hole side down.

installed on a

YC-822/823

Note

the YC-822.

YC-823 bottom

ø6 mm weep hole

[Dimensional diagram]

120

83.5

120

18.2

[YC-822 dimensional diagram]

φ28 (Knockout hole)

4-M4 (for substation mounting)

83.5

66.7

124

Unit: mm

2 (RS-150)

43.5 (RS-150)

φ28 hole

124

52.5

8-5×7 oval hole (for wall mounting)

Accessory screws

The RS-150, RS-160, RS-170, and RS-180 come with 2 types of screws: M4 x 25 and UNC No. 6-32 x 18. For the electrical box provided with unified threads, use the UNC No. 6-32 x 18 screw.

[YC-823 dimensional diagram]

8-5×7 oval hole (for wall mounting)

4-M4 (for substation mounting)

φ28 hole

124

83.5

66.7

124

Unit: mm

φ6 weep hole

Warning

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Traceability Information for Europe

Manufacturer:

TOA Corporation 7-2-1, Minatojima-Nakamachi, Chuo-ku, Kobe, Hyogo, Japan

Authorized representative:

TOA Electronics Europe GmbH Suederstrasse 282, 20537 Hamburg, Germany

URL: http://www.toa.jp/

133-06-00030-00