Toa PE-63B, PE-63W, PE-123B, PE-123W Installation Manual
Please follow the instructions in this manual to obtain the optimum results from this unit.
We also recommend that you keep this manual handy for future reference.
PE-63B, PE-63W
PE-123B, PE-123W
PENDENT SPEAKERS
INSTALLATION MANUAL
INSTALLATION PRECAUTIONS
• Note speaker weight and size when suspending from the ceiling.
• Note terminal polarities when installing two or more speakers in the same location.
APPEARANCE AND DIMENSIONAL DIAGRAM
Mounting screw (white)
Ceiling cover (white)
Speaker cable
Impedance selection switch
Case A
Case B
6
54321
SAFETY PRECAUTIONS
• Be sure to read the instructions in this section carefully
before use.
• Make sure to observe the instructions in this manual as
the conventions of safety symbols and messages
regarded as very important precautions are included.
• We also recommend you keep this instruction manual
handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used
in this manual to prevent bodily injury and property
damage which could result from mishandling. Before
operating your product, read this manual first so you are
thoroughly aware of the potential safety hazards as well as
understand the safety symbols and messages.
When Installing the Unit
• Install the unit only in a location that can structurally
support the weight of the unit and the mounting bracket.
Doing otherwise may result in the speaker falling down
and causing personal injury and/or property damage.
• Be sure to tighten screws when mounting the speaker. If
not tightened, the screws may come off due to a
vibration, etc. and the speaker may fall, resulting in
personal injuries.
When the Unit is in Use
• Do not operate the speaker for an extended period of
time with the sound distorting. This is an indication of a
malfunction, which in turn can cause heat to generate
and result in a fire.
Indicates a potentially hazardous
situation which, if mishandled, could result in death or
serious personal injury.
WARNING
Indicates a potentially hazardous
situation which, if mishandled, could result in moderate
or minor personal injury, and/or property damage.
CAUTION
WARNING
CAUTION
Model No. PE-63B/PE-63W PE-123B/PE-123W
Internal speaker 12 cm dynamic speaker
Rated input 6 W (70 V, 100 V line) 12 W (70 V, 100 V line)
Impedance 830 Ω (70 V line) 420 Ω (70 V line)
1.7 kΩ, 3.3 kΩ, 6.7 kΩ 830 Ω, 1.7 k Ω, 3.3 kΩ
Output SPL 87 dB (1 W, 1 m)
Frequency response 150 - 10,000 Hz
Case color PE-63B/PE-123B : Black
PE-63W/PE-123W: Off white
Weight Approx. 1.2 kg Approx. 1.5 kg
Printed in Japan
133-01-300-5A
INSTALLATION
1. Attach the ceiling bracket to the ceiling using the supplied screws.
2. Cut the speaker cable to the desired length. After processing the cable
end, run the cable through the ceiling cover and suspension bracket.
3. Make a strain-relief knot in the cable, then tighten the suspension
bracket screws to clamp the cable.
4. Connect cables after temporarily suspending the speaker by hooking
one of the two holes in the suspension bracket onto the ceiling bracket
hook.
5. Detach the suspension bracket from the ceiling bracket after cable
connection. Provide ample cable slack in the ceiling.
6. Hook the two holes in the suspension bracket onto the ceiling bracket
hooks.
7. Bend both hooks to prevent accidental detachment of the suspension
bracket from the ceiling bracket.
8. Attach the ceiling cover using the supplied mounting screws.
IMPEDANCE SWITCHING
• The input impedance is factory-preset to 1.7 kΩ (6 W, 100 V line) for the PE-63B/PE-
63 W and to 830 Ω (12 W, 100 V line) for the PE-123B/PE-123W.
• Shift the impedance selection switch to the desired position when changing the
impedance, referring to the following table.
SPECIFICATIONS
Note: The design and specifications are subject to change without notice for improvement.
①②③④
Slide
Setting No.
Impedance 830 Ω 1.7 kΩ 3.3 kΩ 6.7 kΩ
100 V Line
-
6 W 3 W 1.5 W
70 V Line 6 W 3 W 1.5 W 0.8 W
432
1
Setting No.
Impedance 420 Ω 830 Ω 1.7 kΩ 3.3 kΩ
100 V Line
-
12 W 6 W 3 W
70 V Line 12 W 6 W 3 W 1.5 W
432
1
PE-63B/PE-63W PE-123B/PE-123W
Note: Avoid impedance settings marked with a dash -in the table when the line voltage is 100 V, as this will
cause damage to the speaker.
Loading...