Toa HY-W0801W User Manual
HY-W0801W
HS-120W, HS-150W, HS-1200WT,
HS-1500WT
HY-1200VW, HY-1200HW, HY-1500VW,
HY-1500HW
Rolled steel plate, white,
medium gloss, paint
4 kg (8.82 lb)
Hex bolt (with spring and plain washers) M8 x 25 ........ 4
Thank you for purchasing TOA's Wall Mount Bracket.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
1. SAFETY PRECAUTIONS
HY-W0801
HY-W0801W
WALL MOUNT BRACKETS
INSTRUCTION MANUAL
Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.
WARNING
Bolts and nuts used to fix the Bracket A on a wall are not included.
Prepare those that are appropriate for the wall's structure and
composition. Failure to do so may cause the unit to fall, resulting
in personal injury.
WARNING
• Install the unit only in a location that can structurally support the total weight of the unit and the speaker.
Doing otherwise may result in the speaker falling down and causing personal injury and/or property damage.
• Owing to the speaker's size and weight, be sure that at least two persons are available to install the speaker.
Failure to do so could result in personal injury.
• Do not use other methods than specified below to mount the bracket. Extreme force is applied to the unit, or
rust may deteriorate the unit, which then could fall off, possibly resulting in personal injuries.
· As the unit cannot be used separately, be sure to use it in conjunction with the specified bracket.
· As the unit is designed for in-door use, do not install it outdoors.
· Do not install the unit to a ceiling.
• Use nuts and bolts (not supplied with the unit) that are appropriate for the wall's structure and composition.
Failure to do so may cause the speaker to fall, resulting in material damage and possible personal injury.
• Tighten each nut and bolt securely. Ensure that the bracket has no loose joints after installation to prevent
accidents that could result in personal injury.
• Do not hang down from the unit as this may cause it fall away from the wall surface, resulting in personal
injury.
2. GENERAL DESCRIPTION
The HY-W0801 and HY-W0801W Wall Mount Brackets are designed to mount the speaker system on a wall
in conjunction with the optional speaker mount bracket.
3. SPECIFICATIONS
Model
Applicable speaker
Applicable
mounting bracket
Finish
Weight
Accessory
HY-W0801
ES-0851, HS-120B, HS-150B,
HS-1200BT, HS-1500BT
HY-0851ST, HY-0852ST, HY-1200VB,
HY-1200HB, HY-1500VB, HY-1500HB
Rolled steel plate, black,
medium gloss, paint
Note: The design and specifications are subject to change without notice for improvement.
133-05-430-90
URL: http://www.toa.jp/
4. INSTALLATION
The example here shows the installation procedures of the Wall Mount Bracket in conjunction with the HY0851ST or HY-0852ST Speaker Mounting Bracket.
For the installation procedures to the HY-1200 or HY-1500 Series Mounting Bracket, refer to the instruction
manual attached to each mounting bracket.
Step 1. Attach the Bracket B to the HY-0851ST or HY-0852ST Speaker Mounting Bracket.
Note
For the speaker installation, refer to the instruction manual attached to the HY-0851ST or HY-0852ST.
Step 2. Remove the safety bolt from the Bracket A.
Step 3. Install the Bracket A on the wall using 6 bolts.
Step 4. Insert the bolt on the Bracket B into the notch in the Bracket A.
In this event, position the notch between the fixed nut and plain washer on the bolt.
Step 5. Run the safety bolt through the holes in the Bracket A, then tighten the bolt using the nut for M8.
Step 6. Adjust the speaker's horizontal angle.
After adjustment completion, tighten the horizontal angle adjustment nut on the Bracket B.
Horizontal angle adjustment range: 180˚ to the right or left (360˚ rotation)
Step 7. Adjust the speaker's vertical angle at the HY-0851ST or HY-0852ST side.
For adjustment instructions, refer to the instruction manual attached to the HY-0851ST or HY-0852ST.
To the wall surface Bracket A
(supplied with the HY-W0801
and HY-W0801W)
Dimensional diagram
of the Bracket A
6 - ø9.2 (0.36)
90 (3.54)
60 (2.36)
120 (4.72)
201.2 (7.92)
176 (6.93)
Unit: mm (inches)
Note
Be sure to secure with all 6 mounting
holes in the Bracket A.
Nut for M8
Safety bolt
Notch
Bracket B
(supplied with the HY-W0801
and HY-W0801W)
Horizontal angle adjustment nut
Speaker Mounting Bracket
(HY-0851ST or HY-0852ST)
Hex bolt M8 x 25
(supplied with the HY-W0801
and HY-W0801W)
Fixed nut
Plain
washer
Speaker
Loading...