TOA HY-CM20B, HY-CM20W, HY-CM10B Installation Guide

2. GENERAL DESCRIPTION

6. INSTALLATION

INSTALLATION MANUAL

CEILING MOUNT BRACKETS

HY-CM10B HY-CM10W HY-CM20B HY-CM20W

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation.

• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or cautions regarding safety.

• After reading, keep this manual handy for future reference.

WARNING

Indicates a potentially hazardous situation which, if mishandled, could result in death or serious personal injury.

• Install the unit only in a location that can structurally support the weight of the unit and the speaker. Doing otherwise may result in the speaker falling down and causing personal injury and/or property damage.

• Since the unit is des igned for indoor u se, do not install it outdoors. If installed outdoors, the aging of parts causes the speaker to fall off, resulting in personal injury.

• Do not use other methods than specified to mount the unit. Extreme force is applied to the unit and the speaker could fall off, possibly resulting in personal injuries.

• Use nuts and bolts that are appropriate for the ceiling's structure and composition. Failure to do so may cause the speaker to fall, resulting in material damage and possible personal injury.

• Tighten each nut and bolt securely. Ensure that the unit has no loose joints after installation to prevent accidents that could result in personal injury.

• Use the specified speaker cause the speaker to fall off, resulting in personal injury.

• Do not mount the unit in locations exposed to constant vibration. The unit can be damaged by excessive vibration, potentially causing the speaker to fall, which could result in personal injury.

• Do not use anti-rust lubricant. If it contacts resin or rubber parts, they could det eriorate and cause the unit to fall, possibly resulting in personal injury.

in combination. Doing otherwise may

CAUTION

Indicates a potentially hazardous situation which, if mishandled, could result in moderate or minor personal injury, and/or property damage.

• Avoid touching the unit's sharp metal edge to prevent injury.

• Do not hang down from the unit as this may cause it to fall down

or drop, resulting in personal injury and/or property damage.

• Have the unit checked periodically by the shop from where it was purchased. Failure to do so may result in corrosion or damage to the unit that could cause the unit to f all, possibly causing personal injury.

The HY-CM10B and HY-CM10W Ceiling Mount Brackets are used to mount F-1000/1300 Series speakers to a ceiling in a horizontal configuration. The HY-CM20B and HY-CM20W Ceiling Mount Brackets are used to mount F-2000 Series speakers in a horizontal configuration.

Note

To mount the speaker to the ceiling in a vertical orientation, use the brackets supplied with the speaker. For more information, refer to the instruction manual enclosed with the speaker.

3. MOUNTING DIMENSIONS

[HY-CM20B, HY-CM20W][HY-CM10B, HY-CM10W]

108

6.3

40°

9.8 x 41.8 oval hole

30°

15°

ø70

175

72.5

20°

ø40 ø9.8

ø120

Unit: mm

6.3

4. FINISHED ASSEMBLING DIAGRAM

[HY-CM10B, HY-CM10W]

45°

The figure above is an example of F-1000 series installation.

[HY-CM20B, HY-CM20W]

15°

45°

(30°)

Adjustable within this angle range.

5. SPECIFICATIONS

5.1. HY-CM10B and HY-CM10W

Models No. Applicable Speaker

Finish

Dimensions

Weight

Accessories

HY-CM10B

F-1000B, F-1000BT,

F-1300B, F-1300BT

Steel plate, black, paint

48 (w) x 100 (h) x 108 (d) mm

210 g

Machine screw M5 x 10 with washers …4

5.2. HY-CM20B and HY-CM20W

Models No.

Applicable Speaker

Finish

Dimensions

Weight

Accessories

Note

The design and specifications are subject to change without notice for improvement.

HY-CM20B

F-2000B, F-2000BT, F-2000W,F-2000WT,

Steel plate, black, paint

84 (w) x 135 (h) x 175 (d) mm

610 g

Machine screw M5 x 10 with washers …4

HY-CM10W

F-1000W, F-1000WT,

F-1300W, F-1300WT

Steel plate, white,

paint

HY-CM20W

Steel plate, white,

paint

Tip: The wall bracket supplied with each speaker is not used.

Step 1. Attach the speaker bracket to the rear of the speaker

cabinet. Use the screws supplied with the speaker. (HY-CM10B/W: 2 pieces; HY-CM20B/W: 4 pieces)

Note: Mount the bracket so that the speaker is suspended

in a horizontal orientation.

Step 2. Attach a joint bracket to the ceiling mount bracket using

the supplied 4 screws.

Step 3. Attach the ceiling mount bracket to the ceiling using the

ceiling mounting holes.

[HY-CM20B, HY-CM20W][HY-CM10B, HY-CM10W]

Ceiling mounting holes

(2 places)

Note

Hardware used for mounting the ceiling mount bracket to the ceiling is not supplied.

Step 4. Mount the speaker to the joint bracket.

Insert the speaker bracket into the joint bracket and loosely secure the fixing bolt f or temporary speaker installation.

Step 5. Connect the speaker cable to the speaker input terminal.

For connections, refer to the instruction manual enclosed with the speaker.

Ceiling mounting holes

(3 places)

• HY-CM10B, HY-CM10W

The figure above shows the screw mounting positions for the F-1300 series.

Speaker system F-1000 series

Speaker bracket

(supplied with the speaker)

Screw M5 x 20 (supplied with the speaker)

• HY-CM20B, HY-CM20W

Speaker bracket (supplied with the speaker)

Speaker system F-2000 series

Screw M5 x 20

(supplied with the speaker)

Step 6. Adjust the speaker's vertical mounting angle and tighten

the fixing bolt. The speaker angle can be adjusted in 7.5º steps within the range as follows.

• When the HY-10B/W is used F-1000 series: 0º(horizontal) to 45º downward F-1300 series: 7.5º to 45º downward

0°

-20B/W is used

Speaker bracket

Joint bracket

7.5°

30°

45°

Mounting to the ceiling

• When the HY F-2000 series: 15º to 45º downward

Refer to the figures below for the positional relationship between the speaker bracket's "groove" and the joint bracket's "indentation."

[0° (horizontal) position] [7.5° downward position]

(horizontal)

[15° downward position] [45° downward position]

15°

30°

Note

The mating surfaces of the speaker bracket and joint bracket are designed to interlock. Ensure that both parts are securely engaged with each other after mounting is complete.

Accessory screw M5 x 10

HY-CM10B/W

4, 6

Joint bracket (supplied with the speaker)

Fixing bolt (supplied with the speaker)

Accessory screw M5 x 10

Mounting to the ceiling

HY-CM20B/W

4, 6

Joint bracket

Fixing bolt (supplied with the speaker)

(supplied with the speaker)

URL: http://www.toa.jp/

133-01-00122-00