TOA HY-1500VW, HY-1500VB, HY-1500HB, HY-1200HW Instructions

MOUNTING BRACKETS

OPERATING INSTRUCTIONS

V-Series Mounting Brackets

HY-1200VB
HY-1200VW
HY-1500VB

Installation to a ceiling
(V-Series Bracket use)

Installation to a ceiling
(H-Series Bracket use)

TABLE OF CONTENTS

1. SAFETY PRECAUTIONS ............................. 2

2. GENERAL DESCRIPTION ........................... 3

3. SAFETY WIRE INSTALLATION

(For speaker fall prevention) ...................... 4

4. INSTALLING TO A CEILING ........................ 4

HY-1500VW

H-Series Mounting Brackets

HY-1200HB
HY-1200HW
HY-1500HB
HY-1500HW

5. INSTALLING ON A WALL .......................... 10

6. DIMENSIONAL DIAGRAMS ....................... 14

7. SPECIFICATIONS ...................................... 16

Accessories ................................................. 16

Optional products ........................................ 16

Thank you for purchasing TOA's Mounting Bracket.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.

2

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe
operation.

• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.

• After reading, keep this manual handy for future reference.

Safety Symbol and Message Conventions

Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.

Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.

WARNING

When Installing the Unit

• Install the unit only in a location that can structurally support the full weight of the unit and speaker. Doing
otherwise may result in the unit falling down and causing personal injury and/or property damage.

• Since the unit is designed for in-door use, do not install it outdoors. If installed outdoors, the aging of parts
causes the unit to fall off, resulting in personal injury.

• Owing to the speaker's size and weight, be sure that at least two persons are available to install the speaker.
Failure to do so could result in personal injury.

• Do not use other methods than specified to mount the bracket. Extreme force is applied to the unit and the
unit could fall off, possibly resulting in personal injuries.

• Use nuts and bolts that are appropriate for the ceiling's or wall's structure and composition. Failure to do so
may cause the speaker to fall, resulting in material damage and possible personal injury.

• Tighten each nut and bolt securely. Ensure that the bracket has no loose joints after installation to prevent
accidents that could result in personal injury.

• Use the specified speaker in combination. Doing otherwise may cause the speaker to fall off, resulting in
personal injury.

• Do not mount the unit in locations exposed to constant vibration. The mounting bracket can be damaged by
excessive vibration, potentially causing the unit to fall, which could result in personal injury.

• Do not install the unit in indoor swimming pools or such locations where corrosion may occur easily. The
parts deteriorate if corroded, causing the unit to fall, which could result in personal injury.

Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.

CAUTION

When Installing the Unit

• Avoid touching the unit's sharp metal edge to prevent injury.

When the Unit is in Use

• Do not stand or sit on, nor hang down from the unit as this may cause it to fall down or drop, resulting in
personal injury and/or property damage.

• Have the unit checked periodically by the shop from where it was purchased. Failure to do so may result in
corrosion or damage to the speaker or the unit that could cause it to fall, possibly causing personal injury.

3

2. GENERAL DESCRIPTION

These H- and V-Series Mounting Brackets are designed exclusively to mount the HS series speaker system to
a ceiling or wall.

The HY-1200VB, HY-1200VW, HY-1500VB and HY-1500VW (V-Series Mounting Brackets) are for vertical
speaker installation, while the HY-1200HB, HY-1200HW, HY-1500HB and HY-1500HW (H-Series Mounting
Brackets) are for horizontal speaker installation.

They allow speaker's vertical angle to be adjusted*. They also permit speaker's horizontal angle to be
adjusted in conjunction with the optional HY-C0801/HY-C0801W Ceiling Mount Bracket, or HY-W0801/HY­W0801W Wall Mount Bracket.

* Below is the adjustable angle range with reference to the horizontal axis (0°).

[In the case of ceiling installation]

H-Series Brackets: 0° to 90° downward
V-Series Brackets: 15° upward to 90° downward

[In the case of wall installation]

H- and V-Series Brackets: 15° upward to 60° downward

(a) Examples of ceiling installation

For the installation procedures, refer to p. 4, "Installing to a ceiling."

(b) Examples of wall installation

For the installation procedures, refer to p. 10, "Installing on a wall."

When the V-Series
Mounting Bracket is used

When the H-Series
Mounting Bracket is used

When the V-Series
Mounting Bracket is used

When the H-Series
Mounting Bracket is used

When the V-Series Mounting
Bracket is used with an
optional Ceiling mount bracket

When the V-Series Mounting
Bracket is used with an
optional Wall mount bracket

When installing the safety wire, be sure to follow the instructions below.
Failure to do so may cause the speaker to fall off, resulting in personal
injury.

• Use a wire rope of 2 mm (0.08") or more in diameter. (The safety wire is not supplied.)

• Tighten the safety wire to take up the slack. Otherwise, impact shock at speaker fall may cause the wire­connected parts or wire itself to break.

• Install the safety wire to a place that can structurally support the full weight of load.

• Screw a speaker suspension bolt (M8) into one of the screw holes on the speaker's bottom surface.
Then, connect the safety wire to the bolt.

4. INSTALLING TO A CEILING

The brackets to be used are as follows.
For vertical speaker installation: V-Series Mounting Brackets (HY-1200VB, HY-1200VW, HY-1500VB and

HY-1500VW)

For horizontal speaker installation: H-Series Mounting Brackets (HY-1200HB, HY-1200HW, HY-1500HB and

HY-1500HW)

The example here shows the installation procedure of the mounting bracket using the HS-1200 series speaker
system.

4.1. Using the H- or V-Series Mounting Bracket Only

Step 1. Attach the supplied bracket holder to the speaker.

Fix the bracket holder using the supplied 2 screws (M6 x 20)
after aligning its datum line with the positioning mark ( ) on
the speaker system.
Follow the same installation procedure to the other side.

4

3. SAFETY WIRE INSTALLATION (For speaker fall prevention)

When mounting the speaker system to the ceiling or wall, install a safety wire as needed.

1-1. For vertical speaker installation (V-Series Mounting Bracket)

Speaker direction angle can be adjusted from 15° upward to 90° downward.

Note

The screw tightening positions differ depending on the speaker's vertical angle as shown below.
The angle is given with reference to the horizontal axis (0°).

WARNING

Changing the orientation of
the front panel logo

Turn the logo mark while holding its edges
to change its orientation.

Installation position of an M8 bolt
M8 (Screw pitch: 1.25 mm, effective depth: 24 mm)

Note: Unified inch screws cannot be used.

Speaker's
bottom surface

Datum line
(on the bracket holder)

Positioning mark
(on the speaker system)

Bracket holder
(accessory)

Adjustable speaker direction angle

• 15° upward to 60° downward

• 75° to 90° downward

Machine screw M6 x 20 (accessory)

5

Note

The bolt mounting position differs depending on the speaker's vertical angle as shown below.
The angle is given with reference to the horizontal axis (0°).

1-2. For horizontal speaker installation (H-Series Mounting Bracket)

Speaker direction angle can be adjusted from 0° to 90° downward.

2-2. For horizontal speaker installation (H-Series Mounting Bracket)

Speaker direction angle can be adjusted from 0° to 90° downward.

Step 2. Screw the supplied hex bolt loosely into the bracket holder.

Leave the bolt head out about 4 mm (0.16") to allow the
mounting bracket to be inserted.
Follow the same installation procedure to the other side.

2-1. For vertical speaker installation (V-Series Mounting Bracket)

Speaker direction angle can be adjusted from 15° upward to 90° downward.

Adjustable speaker direction angle

• 0° to 60° downward

• 75° to 90° downward

Bracket holder
(accessory)

Machine screw M6 x 20
(accessory)

Adjustable speaker direction angle

• 15° upward to 60° downward

• 75° to 90° downward

About 4 mm (0.16")

Hex bolt M6 x 30
(accessory)

Bracket holder

Bracket holder

Adjustable speaker direction angle

• 0° to 60° downward

• 75° to 90° downward

Bracket holder

Hex bolt M6 x 30
(accessory)

Hex bolt M6 x 30
(accessory)

6

Step 3. Install the mounting bracket to the ceiling.

For the dimensions of the mounting bracket, refer to p. 14, "Dimensional Diagrams."

The following figure shows an example for the V-Series Mounting Bracket installation.

Step 4. Install the speaker to the mounting bracket.

Insert the loosely fitted bolts in Step 2 into the
mounting bracket's notches until the bolts fit in at
the end.

The figure at right shows an example for the
speaker system installation to the V-Series
Mounting Bracket.
Similarly, the speaker system can be installed to
the H-Series Mounting Bracket.

Step 5. Connect the speaker cable to the speaker system.

Step 6. Adjust the speaker direction.

Angle adjustment range is as shown below.
Determine the speaker angle in the way that the screw holes in the bracket holder match with the
angle adjustment holes in the mounting bracket, then fix the speaker using the supplied hex bolt (M6
x 30).

Follow the same installation procedure to the other side.

6-1. When adjusting the speaker direction within the range of 15° upward to 60° downward using the V-

Series Mounting Bracket.

Bolts and nuts used to fix a bracket to a ceiling are not
included. Prepare those that are appropriate for the ceiling's
structure and composition. Failure to do so may cause the
unit to fall, resulting in personal injury.

WARNING

To the

Mounting bracket

Front direction

ceiling surface

Ensure that the notch in the bracket is pointing
in the speaker's front direction.

Note on bracket mounting

Do not use these 4 round holes.

Use these 4 oval holes to install the
bracket to the ceiling.

Mounting bracket installed
to the ceiling

Loosely fitted bolt
in Step 2

0° (Horizontal)

15°

60°

Ceiling

Hex bolt M6 x 30
(accessory)

The speaker angle is adjustable in 7.5° steps with
the angle adjustment holes in the mounting bracket.

Angle adjustment hole

7.5°

10 × 7.5° (75°)

7

6-2. When adjusting the speaker direction within the range of 75° to 90° downward using the V-Series

Mounting Bracket.

6-3. When adjusting the speaker direction within the range of 0° to 60° downward using the H-Series

Mounting Bracket.

6-4. When adjusting the speaker direction within the range of 75° to 90° downward using the H-Series

Mounting Bracket.

Step 7. Tighten the loosely fitted bolts in Step 2.

Note: Check that all bolts are securely tightened.

For the speaker installed view, refer to p. 3, "Examples of ceiling installation."

Hex bolt M6 x 30
(accessory)

0° (Horizontal)

90°

Ceiling

75°

15°

The speaker angle is adjustable in 7.5° steps with
the angle adjustment holes in the mounting bracket.

Angle adjustment hole

7.5°

7.5°

Ceiling

0° (Horizontal)

The speaker angle is adjustable in 7.5° steps with
the angle adjustment holes in the mounting bracket.

Angle adjustment hole

60°

7.5°

Hex bolt M6 x 30
(accessory)

8 × 7.5° (60°)

0° (Horizontal)

90°

Ceiling

75°

15°

Hex bolt M6 x 30
(accessory)

The speaker angle is adjustable in 7.5° steps with
the angle adjustment holes in the mounting bracket.

Angle adjustment hole

7.5° 7.5°

8

4.2. When Using in conjunction with the Optional Mount Bracket

The H- or V-Series Mounting Bracket allows speaker's horizontal angle to be adjusted in conjunction with the
optional HY-C0801 or HY-C0801W Ceiling Mount Bracket.

The following figure shows an example of vertical speaker installation.

To the ceiling surface

Bracket A
(supplied with the HY-C0801
and HY-C0801W)

Hex bolt M8 x 25
(supplied with the HY-C0801
and HY-C0801W)

Nut for M8

Fixed nut

Bracket B
(supplied with the
HY-C0801 and HY-C0801W)

Horizontal
angle adjustment nut

H- or V-Series
Mounting Bracket

Nut for M8
(supplied with the H- and
V-Series Mounting Brackets)

Plain washer

Plain washer for M8
(supplied with the H- and
V-Series Mounting Brackets)

Notch

Safety bolt

[Dimensional diagram of the Bracket A]

150 (5.91)

8 - ø11 (0.43)

150 (5.91)

120 (4.72)

120 (4.72)

Unit: mm (inches)

Note

Be sure to secure with at least all 4 corner­mounting holes in the Bracket A.

Bracket holder
(supplied with the H- and V-Series Mounting Brackets)

Speaker system
(HS-120/150/1200/1500 series)

9

Step 1. Attach the supplied bracket holders and hex bolts to the speaker.

For the procedures, refer to Steps 1 and 2 in the "Using the H- or V-Series Mounting Bracket Only" on
page 4.

Step 2. Remove the safety bolt from the Bracket A of the HY-C0801 or HY-C0801W to detach the Bracket B.

Step 3. Attach the removed Bracket B to the H- or V-Series Mounting Bracket.

Be sure to use the hex bolts supplied with the HY-C0801 or HY-C0801W, and the nuts for M8 and
plain washers for M8 supplied with the H- or V-Series Mounting Bracket.

Step 4. Install the Bracket A to the ceiling using 4 bolts or more.

Step 5. Insert the bolt on the Bracket B into the notch in the Bracket A so that the notch is positioned between

the fixed nut and plain washer on the bolt.

Step 6. Run the safety bolt through the holes in the Bracket A, then tighten the bolt using the nut for M8.

Step 7. Mount the speaker to the H- or V-Series Mounting Bracket, then determine the speaker's vertical

angle.

For the speaker installation, refer to Steps 4 - 7 in "Using the H- or V-Series Mounting Bracket Only"
on page 6.

Step 8. Adjust the speaker's horizontal angle.

After adjustment completion, tighten the horizontal angle adjustment nut on the Bracket B.

Notes

• The adjustable horizontal angle is 360° rotation.

• Installing the speaker near a wall or projection limits the adjustable angle range.

For the speaker installed view, refer to p. 3, "Examples of ceiling installation."

Bolts and nuts used to fix the Bracket A to a ceiling are not
included. Prepare those that are appropriate for the ceiling's
structure and composition. Failure to do so may cause the
unit to fall, resulting in personal injury.

WARNING

10

Step 2. Screw the supplied hex bolt loosely into the bracket holder.

Leave the bolt head out about 4 mm (0.16") to allow the
mounting bracket to be inserted.
Follow the same installation procedure to the other side.

2-1. For vertical speaker installation

(V-Series Mounting Bracket)

2-2. For horizontal speaker installation

(H-Series Mounting Bracket)

5. INSTALLING ON A WALL

The brackets to be used are as follows.
For vertical speaker installation: V-Series Mounting Brackets (HY-1200VB, HY-1200VW, HY-1500VB and

HY-1500VW)

For horizontal speaker installation: H-Series Mounting Brackets (HY-1200HB, HY-1200HW, HY-1500HB and

HY-1500HW)

The example here shows the installation procedure of the mounting bracket using the HS-1200 series speaker
system.

5.1. Using the H- or V-Series Mounting Bracket Only

The speaker direction angle is within the range of 15° upward to 60° downward for both the vertical and
horizontal speaker installations.
The angle is given with reference to the horizontal axis (0°).

Step 1. Attach the supplied bracket holder to the speaker.

Fix the bracket holder using the supplied 2 screws (M6 x 20)
after aligning its datum line with the positioning mark ( ) on
the speaker system.
Follow the same installation procedure to the other side.

1-1. For vertical speaker installation

(V-Series Mounting Bracket)

1-2. For horizontal speaker installation

(H-Series Mounting Bracket)

Datum line
(on the bracket holder)

Positioning mark
(on the speaker system)

Bracket holder
(accessory)

Machine screw
M6 x 20 (accessory)

About 4 mm (0.16")

Hex bolt M6 x 30
(accessory)

Bracket holder

Bracket holder

Hex bolt M6 x 30
(accessory)

11

Step 3. Install the mounting bracket on the wall.

For the dimensions of the mounting bracket, refer to p.14, "Dimensional Diagrams."

The following figure shows an example of the V-Series Mounting Bracket installation.

Step 4. Install the speaker to the mounting bracket.

Insert the loosely fitted bolts in Step 2 into the
mounting bracket's notches until the bolts fit in at
the end.

The figure at right shows an example for the
speaker system installation to the V-Series
Mounting Bracket.
Similarly, the speaker system can be installed to
the H-Series Mounting Bracket.

Step 5. Connect the speaker cable to the speaker system.

Step 6. Adjust the speaker direction.

Speaker direction can be adjusted is within the range of 15° upward to 60° downward for both the V-

and H-Series Mounting Brackets.
Determine the speaker angle in the way that the screw hole in the bracket holder matches with the angle
adjustment hole in the mounting bracket, then fix the speaker using the supplied hex bolt (M6 x 30).
Follow the same installation procedure to the other side.

6-1. For the V-Series Mounting Bracket

WARNING

Bolts and nuts used to fix a bracket on a wall are not
included. Prepare those that are appropriate for the wall's
structure and composition. Failure to do so may cause the
unit to fall, resulting in personal injury.

Note on bracket mounting

To the wall surface

Up

Mounting bracket

Ensure that the notch in the bracket points upward.

Do not use these 4 round holes.

Use these 4 oval holes to install the
bracket on the wall.

Mounting bracket installed on the wall

Loosely fitted bolt in Step 2

Hex bolt M6 x 30

0° (Horizontal)

15°

60°

(accessory)

Wall

The speaker angle is adjustable in 7.5° steps with
the angle adjustment hole in the mounting bracket.

7.5°

10 × 7.5° (75°)

Angle adjustment hole

12

Step 7. Tighten the loosely fitted bolts in Step 2.

Note: Check that all bolts are securely tightened.

For the speaker installed view, refer to p. 3, "Examples of wall installation."

5.2. When Using in conjunction with the Optional Mount Bracket

The H- or V-Series Mounting Bracket allows speaker's horizontal angle to be adjusted in conjunction with the
optional HY-W0801 or HY-W0801W Wall Mount Bracket.

Notes

• When the HY-1200 Series Bracket is used, the adjustable angle range is as follows.
Vertical angle range: 15° upward to 90° downward (with reference to the horizontal axis as 0°)
Horizontal angle range: 90° to the left or right (with reference to the front direction as 0°)

• When the HY-1500 Series Bracket is used, the adjustable angle range is limited.
For details, refer to "HY-1500 Series Brackets' adjustable angle range" on the next page.

6-2. For the H-Series Mounting Bracket

0° (Horizontal)

15°

60°

Hex bolt (M6 x 30)
(accessory)

Wall

The speaker angle is adjustable in 7.5° steps with
the angle adjustment hole in the mounting bracket.

Angle adjustment hole

7.5°

10 × 7.5° (75°)

To the wall surface

Safety bolt

[Dimensional diagram of
the Bracket A]

90 (3.54)

176 (6.93)

6 - ø9.2 (0.36)

120

(4.72)

201.2 (7.92)

60 (2.36)

Bracket A
(supplied with the HY-W0801 and HY-W0801W)

Nut for M8

Notch

Plain washer

Horizontal angle
adjustment nut

Hex bolt M8 x 25
(supplied with the HY-W0801 and HY-W0801W)

Fixed nut

Bracket B
(supplied with the HY-W0801
and HY-W0801W)

H- or V-Series Mounting Bracket

Plain washer for M8
(supplied with the H- and V-Series
Mounting brackets)

Nut for M8
(supplied with the H- and V-Series
Mounting brackets)

Speaker system
(HS-120/150/1200/1500 series)

Unit: mm (inches)

Note

Be sure to use 6 mounting holes
in the Bracket A.

Bracket holder
(supplied with the
H- or V-Series Mounting bracket)

This figure shows an example
of vertical speaker installation.

13

Step 1. Attach the supplied bracket holders and hex bolts to the speaker.

For the procedures, refer to Steps 1 and 2 in the "Using the H- or V-Series Mounting Bracket Only" on
page 4.

Step 2. Attach the Bracket B of the HY-W0801 or HY-W0801W to the H- or V-Series Mounting Bracket.

Be sure to use the hex bolts supplied with the HY-W0801 or HY-W0801W, and the nuts for M8 and
plain washers for M8 supplied with the H- or V-Series Mounting Bracket.

Step 3. Remove the safety bolt from the Bracket A.

Step 4. Install the Bracket A on the wall using 6 bolts.

Step 5. Insert the bolt on the bracket B into the notch in the Bracket A so that the notch is positioned between

the fixed nut and plain washer on the bolt.

Step 6. Run the safety bolt through the holes in the Bracket A, then tighten the bolt using the nut for M8.

Step 7. Mount the speaker to the H- or V-Series Mounting Bracket, then adjust the speaker direction.

For the speaker installation, refer to Steps 4 - 7 in "Using the H- or V-Series Mounting Bracket Only"
on page 6.
After adjusting the horizontal angle, tighten the horizontal angle adjustment nut on the Bracket B.

HY-1500 Series Brackets' adjustable angle range (shaded area)

Bolts and nuts used to fix the Bracket A on a wall are not
included. Prepare those that are appropriate for the wall's
structure and composition. Failure to do so may cause the
unit to fall, resulting in personal injury.

WARNING

For the speaker installed view, refer to p. 3, "Examples of wall installation."

Adjustable angle range (shaded area) when
the HY-1500VB or HY-1500VW is used

Wall

(Viewed from top)

Minus (

-

) direction

Reference (0° )

Adjustable angle range (shaded area) when
the HY-1500HB or HY-1500HW is used

Plus (+) direction

Adjustable horizontal angle (degree)

Adjustable horizontal angle (degree)

Wall

(Viewed from top)

Minus (

-

) direction

Reference (0° )

Plus (+) direction

Adjustable vertical angle (degree) Adjustable vertical angle (degree)

14

6. DIMENSIONAL DIAGRAMS

6.1. HY-1200VB and HY-1200VW

6.2. HY-1200HB and HY-1200HW

[Top]

366.4 (14.43)

224 (8.82)

150 (5.91)

40 (1.57)

60 (2.36)

Unit: mm (inches)

90 (3.54)

4 - ø8.5 (0.33)

4 - 11 × 36 (0.43 x 1.42)

[Front] [Side]

183.2 (7.21)

328.2 (12.92)

3.2 (0.13)

337.9 (13.3)

[Top]

31 (1.22)

70 (2.76)

15°

75° = 1

R55 (2.17)

.5°

× 7

0

395.4 (15.57)

224 (8.82)

150 (5.91)

4 - ø8.5 (0.33)

40 (1.57)

4 - 11×36 (0.43 x 1.42)

90 (3.54)

60 (2.36)

[Front] [Side]

3.2 (0.13)

241.5 (9.51)

31 (1.22)

70 (2.76)

Unit: mm (inches)

15°

0

75° = 1

× 7

R55(

.5°

2.17)

15

6.3. HY-1500VB and HY-1500VW

6.4. HY-1500HB and HY-1500HW

[Top]

460.4 (18.13)

294 (11.57)

150 (5.91)

40 (1.57)

60 (2.36)

Unit: mm (inches)

90 (3.54)

4 - ø8.5 (0.33)

4 - 11 × 36 (0.43 x 1.42)

[Front] [Side]

13.2 (0.52)

3.2 (0.13)

410.9 (16.18)

228.2 (8.98)

403.2 (15.87)

31 (1.22)

70 (2.76)

°

15

75° =

× 7

0

1

R55 (2.17)

.5°

[Top]

485.4 (19.11)

294 (11.57)

150 (5.91)

4 - ø8.5 (0.33)

40 (1.57)

4 - 11 × 36 (0.43 x 1.42)

90 (3.54)

60 (2.36)

[Front] [Side]

13.2 (0.52)

3.2 (0.13)

288 (11.34)

31 (1.22)

70 (2.76)

Unit: mm (inches)

R55 (2.17)

15°

.5°

× 7

0

1

75° =

7. SPECIFICATIONS

[HY-1200 Series Mounting Brackets]

Model

Applicable speaker HS-120B,

Finish

Dimensions

Weight 2.2 kg (4.85 lb) 1.9 kg (4.19 lb)

HY-1200VB HY-1200VW HY-1200HB HY-1200HW

HS-120W,

HS-1200BT

Rolled steel plate,

paint, black

366.4 (w) x 328.2 (h) x 90 (d) mm

14.43 (w) x 12.92 (h) x 3.54 (d) inches

HS-1200WT

Rolled steel plate,

paint, white

HS-120B,

HS-1200BT

Rolled steel plate,

paint, black

395.4 (w) x 241.5 (h) x 90 (d) mm

15.57 (w) x 9.51 (h) x 3.54 (d) inches

Rolled steel plate,

[HY-1500 Series Mounting Brackets]

Model

Applicable speaker HS-150B,

Finish

Dimensions

Weight 3 kg (6.61 lb) 2.4 kg (5.29 lb)

HY-1500VB HY-1500VW HY-1500HB HY-1500HW

HS-150W,

HS-1500BT

Rolled steel plate,

paint, black

460.4 (w) x 403.2 (h) x 90 (d) mm

18.13 (w) x 15.87 (h) x 3.54 (d) inches

HS-1500WT

Rolled steel plate,

paint, white

HS-150B,

HS-1500BT

Rolled steel plate,

paint, black

485.4 (w) x 288 (h) x 90 (d) mm

19.11 (w) x 11.34 (h) x 3.54 (d) inches

Rolled steel plate,

HS-120W,

HS-1200WT

paint, white

HS-150W,

HS-1500WT

paint, white

Note: The design and specifications are subject to change without notice for improvement.

• Accessories

Bracket holder ........................................... 2

Machine screw M6 x 20 ............................. 4

Hex bolt M6 x 30 ........................................ 4

Plain washer for M8 (used when installing in conjunction with the optional bracket) ....... 4

Nut for M8 (used when installing in conjunction with the optional bracket) ...................... 4

• Optional products

Ceiling Mount Bracket: HY-C0801, HY-C0801W
Wall Mount Bracket: HY-W0801, HY-W0801W

URL: http://www.toa.jp/

133-01-00117-00