Toa HY-0871WS User Manual
Please follow the instructions in this manual to obtain the optimum results from this unit.
We also recommend that you keep this manual handy for future reference.
HY-0871WS
SPEAKER MOUNTING BRACKET
INSTRUCTION MANUAL
SAFETY PRECAUTIONS
• Be sure to read the instructions in this section carefully
before use.
• Make sure to observe the instructions in this manual as
the conventions of safety symbols and messages
regarded as very important precautions are included.
• We also recommend you keep this instruction manual
handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used
in this manual to prevent bodily injury and property
damage which could result from mishandling. Before
operating your product, read this manual first so you are
thoroughly aware of the potential safety hazards as well as
understand the safety symbols and messages.
WARNING Indicates a potentially hazardous
situation which, if mishandled, could result in death or
serious personal injury.
• Install the unit only in a location that can structurally
support the weight of the unit and the mounting bracket.
Doing otherwise may result in the speaker falling down
and causing personal injury and/or property damage.
• Owing to the speaker's size and weight, be sure that at
least two persons are available to install the speaker.
Failure to do so could result in personal injury.
•
Do not hang down from the bracket, as the bracket could
fall, resulting in personal injury.
•
Use nuts and bolts (not supplied with the unit) that are
appropriate for the wall's structure and composition. If the
wall cannot withstand the weight of both the speaker and
bracket, the speaker may fall, resulting in material damage
and possible personal injury.
GENERAL DESCRIPTION
The HY-0871WS Speaker Mounting Bracket is specially
designed for mounting TOA's ES-0871 Speaker System to
walls.
COMPONENTS
Arm A ................................................................. 2
Arm B ................................................................. 2
Bracket ............................................................... 3
Base ................................................................... 1
Hexagon bolt W3/8" x 45 ................................. 10
Spring washer (W3/8") ..................................... 10
Plain washer (W3/8") ....................................... 10
Square nut (W3/8") ............................................ 6
Hexagon bolt M8
(with spring washer and plain washer) ............... 2
INSTALLATION
•
Wall Mounting Dimension
Unit : mm
150
75
ES-0871
186
111
825
895
Printed in Japan
133-05-319-30
•
Installation
•
Adjustable Mounting Angle Range
[Vertical (downward-facing) angle]
Use Arm A or B to set vertical mounting angle. The following table shows the adjustable mounting angle range of each
adjustment slot of (a) to (e). Select either Arm A or B depending on the desired speaker mounting angle.
[Horizontal (leftward/rightward) angle]
To change the horizontal angle, use the horizontal angle adjustment slot in the base and bracket. (Refer to the section
"Installation".) Leftward and rightward angles are both adjustable in the range of 15°.
SPECIFICATIONS
Finish Rolled steel plate, paint, black, semi-mat
Weight 4 kg
Note : The design and specifications are subject to change without notice for improvement.
Horizontal angle
adjustment slot
Hexagon bolt M8
(with spring washer
and plain washer)
ES-0871
Square nut
(W3/8")
Plain washer (W3/8")
Spring washer (W3/8")
Hexagon bolt W3/8" x 45
Bracket
Supporting point
Arm A
(Select either Arm A or B
depending on the desired
speaker mounting angle.)
Base
Horizontal angle adjustment slot
Adjustment slot
(a)
(b)
(c)
(d)
(e)
Adjustable vertical (downward-facing)
angle range
0°
3.7° – 7.3°
0°
11° – 14.6°
18.3° – 22°
(e)
(d)
(a)(b)
(c)
Supporting point
Arm A
Supporting point
Arm B
Loading...