TOA HA-1010-AM Users Manual
Wiring diagram HA-1010-AM
8Ω 8Ω 8Ω 8Ω 8Ω 8Ω 8Ω 8Ω
16Ω
5. SPECIFICATIONS
Model
Rated Input
Rated Impedance
Sound Pressure Level
Maximum Sound Pressure Level
INSTRUCTION MANUAL
LONG RANGE
SLIM ARRAY SPEAKERS
200Ω
100Ω
COM
0
BLUE
BLACK
WHITE
HA-1010-AS HA-1010-EA HA-1010-AMHA-1010-EB
100V line: 200Ω (50W), 330Ω (30W)
114dB (1W, 1m)
131dB (50W, 1m)
Thank you for purcahsing TOA’s LONG RANGE SLIM ARRAY SPEAKERS.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
50W
70V line: 100Ω (50W), 200Ω (25W)
25V line: 100Ω (6W), 200Ω (3W)
HA-1010-AS
HA-1010-AM
HA-1010-EA
HA-1010-EB
Frequency Response
Directivity Angle
Speaker Component
Operating Temperature
Water Protection
Finish
Dimensions
Weight
Note
• The design and specifications are subject to change without notice for improvement.
• Accessories
Mounting Bracket ........................................
Hexagonal Bolt (M8 x 20) ...........................
Washer (M8) ...............................................
Spring Washer (M8) ....................................
Washer (M10) .............................................
Spring Washer (M10) ..................................
Nut (M10) ....................................................
2
2
4
2
8
4
4
Horizontal: 90˚ (2kHz), Vertical: 15˚ (2kHz)
-20˚C to +55˚C (-4˚F to +131˚F)
Case, Panel: Aluminum, salt-resistant, paint, grey
Bracket: Stainless steel (SUS 304), paint, grey
167(w) x 1233(h) x 140.5(d) mm (6.57” x 48.54” x 5.53”)
350Hz − 7kHz
Horn speaker unit x 8
IPX5
Front grille: Aluminum, black
13.5kg (29.76lb)
1. SAFETY PRECAUTIONS
• Be sure to read the instruction manual in this section
carefully before use.
• Make sure to observe the instruction in this manual as the
convention of safety symbols and messages regarded as
very important precautions are included.
• We also recommend you keep this instruction manual
handy for future reference.
WARNING
Indicates a potentially hazardous situation which, if
mishandled, could result in death or serious
personal injury.
When Installing the Unit
• Install the speaker only in a location that can structurally
support the weight of the speaker and the mounting
bracket. Doing otherwise may result in the unit falling
down and causing personal injury and/or property
damage.
CAUTION
Indicates a potentially hazardous situation which, if
mishandled, could result in moderate or minor
personal injury, and/or property damage.
When Installing the Unit
• Do not place heavy object on the speaker as this may
cause it to fall or break which may result in personal injury
and/or property damage. In addition, the object itself may
fall off and cause injury and/or damage.
• Do not stand or sit on, nor hang down from the speaker as
this may cause it to fall down or drop, resulting in personal
injury and/or property damage.
• Do not operate the speaker for an extend period of time
with the sound distorting. Doing so may cause the
connected speakers to heat, resulting in a fire.
URL : http://www.toa.com.sg/
2. FEATURES
The HA-1010 is long range speaker slim array is composed of multiple horn speaker positioned in an array. It features
long-range sound coverage further than conventional horn speakers, narrowly focused vertical directivity that allows
excessive volume to be controlled at closer proximity, and form a continuous linear sound source, achieving uniform sound
pressure with less attenuation due to distance.
3. INSTALLATION PRECAUTIONS3. INSTALLATION PRECAUTIONS
Step 3. Install the long range slim array to the bracket
that have been installed to the mounting surface
using supplied hexagon bolt, washer, and spring
washer to top and bottom bracket.
Top bracket
• This long range slim array speakers have
feature a drain hole built into same panel
that holds the speaker cord. For proper
drainage, when installation please ensure
that this panel faces down toward the
ground or follow the instruction of direction
label at the rear case.
• When using the other bracket, please to use
TOA’s optional bracket solely designed for
mounting this speaker or it must have
strength enough to stand the speaker
weight.
MAKE SURE THAT SPEAKER IS MOUNTE D
WITH THE SIDE INDICATED BY THE ARROW UP.
IF THE SPEAKER MOUNTED UPSIDE DOWN.
RAINWATER GETS INTO THE SPEAK ER FROM
DRAI N HOLE ON THE BOT TOM PL ATE.
CAUSING BREAK DOWNS OR ACCIDENT S.
WHEN MOUNTING. BE SURE TO USE TOA’S
OPTIONAL BRACKE T SOLELY DESIGNED FOR
MOUNTING THIS SPEAKER. WHEN USING
OTHER BRA CKET. IT MUST HAVE STR ENGTH
ENOUGH TO STAND THE SPEAKER WEIGHT.
3. INSTALLATION
Step 1. Make the sign for drill guide at the surface or
location that can structurally support the weight
of the speaker. Prepare the proper dyna bolt
that suitable with hole of bracket. Dimensions
of sign for drill guide and hole of bracket as
shown in the picture.
Holes bracket
4 - Ø9
Mounting Bracket
(accessory)
25(0.98”)
(50.67”)
1287
(0.98”)
25
Case
50
(1.97”)
Drain hole
Speaker cord
Unit: mm (in)
Guide for
top bracket
Surface for drill
Guide for
bottom bracket
Hexagon bolt M8 x 20
Spring washer (for M8)
Washer (for M8)
HA-1010
Note
When the speaker installation need slope angel, use the
optional Q-HA-1100 speaker bracket.
4. SPEAKER CORD COLOR CODING
HA-1010-AM
Line voltage 70V LINE
Rated input
Impedance
Cord color coding
HOT
COM
Washer (for M8)
Spring washer (for M8)
Hexagon bolt M8 x 20
50W 25W
100Ω 200Ω
BLACK
WHITE
BLUE
WHITE
Bottom bracket
25V LINE
6W 3W
100Ω 200Ω
BLACK
WHITE
BLUE
WHITE
Step 2. Drill the surface that have been marked, install
the proper dyna bolt then the both of top and
bottom bracket.
Note
Dyna bolts and nuts are not provided.
Mounting surface
Nut
Mounting Bracket
(accessory)
Dyna bolt
50
(1.97”)
HA-1010-AS, HA-1010-EA, HA-1010-EB
Speaker cord
For connections,
refer to the table.
Line voltage 100V LINE
Rated input
Impedance
Cord color coding
5. WIRING DIAGRAM
Wiring diagram HA-1010-AS, HA-1010-EA, HA-1010-EB
8Ω 8Ω 8Ω 8Ω 8Ω 8Ω 8Ω 8Ω
16Ω
330Ω
200Ω
COM
0
BLUE
BLACK
WHITE
HOT
COM
50W 30W
200Ω 330Ω
BLACK
WHITE
BLUE
WHITE
Loading...