Toa DX-0808 Operating Instructions Manual

OPERATING INSTRUCTIONS

MATRIX UNIT

CAUTION

TO REDUCE THE RISK OF ELECTRICAL
SHOCK, DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL

DX-0808

THE LIGHTNING FLASH WITH
ARROWHEAD WITHIN A TRIANGLE IS
INTENDED TO TELL THE USER THAT
PARTS INSIDE THE PRODUCT ARE A
RISK OF ELECTRIC SHOCK TO
PERSONS.

THE EXCLAMATION POINT WITHIN A
TRIANGLE IS INTENDED TO TELL THE
USER THAT IMPORTANT OPERATING
AND SERVICING INSTRUCTIONS ARE
IN THE PAPERS WITH THE
APPLIANCE.

CONTENTS

1 . GENERAL DESCRIPTION

2. FEATURES

3. HANDLING PRECAUTIONS

4. SIGNAL PROCESSING FUNCTION

5. NOMENCLATURE AND FUNCTIONS

[FRONT PANEL]

[FRONT POCKET]

[REAR PANEL]

6. PERSONAL COMPUTER CONNECTIONS

Please follow the instructions in this manual to obtain the optimum results from this unit.
We also recommend that you keep this manual handy fo r futur e re feren ce.

2

7. UNIT ID NUMBER SETTING

2

8. USING THE MEMORY I/O CONNECTOR

2

2

9. EXPANSION AND INTERNAL SWITCH SETTING

3

3

10. RECALLING THE PATTERN MEMORIES

4

5

11.

SPECIFICATIONS

12.

APPEARANCE

6

TOA Corporation

8

9

10

11

11

12

1. GENERAL DESCRIPTION

A 2-unit size, digitally-controlled analog matrix unit, the TOA DX-0808 is equipped with 8 inputs, 8 buses, and 8

outputs. Using dedicated software operating on a personal computer, an operator can set each function in

detail. The settings can be stored in the component's internal memory, and the memory can be recalled from

the component even when not connected to a personal computer.

2. FEATURES

Free zone selection and level adjustment from PC.

Up to 16 setting patterns can be stored, which can be easily recalled even without connecting to a personal

computer.

The stored information can be remotely recalled from external equipment, and the memory selection status

can be output.

Expandable input and output because of eight-bus construction.

RS-485 ports control up to 30 units.

A 3-step system locking function prevents problems resulting from operator error.

Wide operating voltage range : 90 VAC - 250 VAC.

3. HANDLING PRECAUTIONS

The matrix unit has no parameter setting functions, so you use a personal computer and the dedicated TOA

software program to set the parameters.

Turn the power switch ON only after all terminals and other wires are connected.

Avoid installing the unit near a heater or exposing it to direct sunlight as this may damage the unit. Also, do

not install the unit in humid or dusty locations.

Do not jolt or vibrate the DX-0808 as it is a precision instrument.

Never attempt to service the unit yourself as opening or moving the covers may expose you to dangerous

voltage or other hazards. Refer all servicing to TOA dealers.

4. SIGNAL PROCESSING FUNCTION

The DX-0808 is a digitally-controlled matrix unit.

All parameter setting functions and setting value ranges are, therefore, accomplished by operating the personal

computer software. Refer to the software specifications for details of the functions.

2

5. NOMENCLATURE AND FUNCTIONS

[FRONT PANEL]

Status indicator LED

This indicator provides a matrix display of the input-to-bus assignment status and output selection status.

Power switch

Set this switch to ON and the processor starts operating in the status it was in just before the power was last

turned OFF. The power LED lamp lights at this time.

Master unit indicator [MASTER]

The unit in which the ID number is set to "1" (LED lamp lights) functions as a master unit when switching

between stored information. For details, refer to p. 8. "7. UNIT ID NUMBER SETTING".

Memory call key [MEMORY]

This key is used to recall the memory pattern selected with the memory/unit number selection key.

Unit ID number indication key [UNIT ID]

This key is used to show the unit ID number on the display.

Memory/unit ID number display [MEMORY/UNIT ID]

Either the memory number or unit ID number is displayed. Usually, the selected memory number is

displayed.

Memory/unit ID number selection key

The memory number or unit ID number can be selected with the UP and DOWN keys.

Pocket cover

3

[FRONT POCKET]

Communications port selection switch [PORT]

This switch is used to select the communications port your computer is connected to. RS-232C is valid only

when controlling a single unit, and the front- or rear-mounted D-SUB connector can be used. Use RS-485

when controlling multiple units. XLR connectors for RS-485 are mounted on the back of the unit.

System locking switch [LOCK]

Use this switch to set how the hardware is locked.

OFF : All functions are available (unlocked), such as memory switching.

1 : All functions are locked except memory switching.

2 : All front panel facilities are locked.

Note

Make sure the power is switched ON when you use this switch.

RS-232C communications port [RS-232C]

This is a 9-pin D-SUB connector for RS-232C communications, and can only be used when the

communications port selection switch is set to "RS-232C". This port is connected in parallel to the

rear-mounted D-SUB connector for RS-232C. For details, refer to p.6 "6. PERSONAL COMPUTER

CONNECTIONS".

Unit ID number setting key [SET UNIT ID No.]

Use this key to set the unit ID number. For details, refer to p.8 "8.UNIT ID NUMBER SETTING".

4