Toa DA-250DH CE-AU User Manual

DUAL POWER AMPLIFIERS

DA-250DH CE301
DA-250DH CE-GB
DA-250DH CE-AU

DA-250D

DA-250DH

Thank you for purchasing TOA's Dual Power Amplifier.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.

OPERATING INSTRUCTIONS

An all-pole mains switch with a contact separation of at least 3 mm in each pole shall be
incorporated in the electrical installation of the building.

DA-250D CE301
DA-250D CE-GB
DA-250D CE-AU

2

TABLE OF CONTENTS

1. SAFETY PRECAUTIONS ............................................................................... 3

2. GENERAL DESCRIPTION ............................................................................. 4

3. FEATURES .......................................................................................................... 4

4. HANDLING PRECAUTIONS .......................................................................... 5

5. INSTALLATION PRECAUTIONS ................................................................. 5

6. NOMENCLATURE AND FUNCTIONS

Front ......................................................................................................................... 6

Rear .......................................................................................................................... 7

7. SETTINGS AND CONNECTIONS

7.1. Switch Settings and Speaker Connections

7.1.1. When using the DA-250D ........................................................................ 8

7.1.2. When using the DA-250DH ...................................................................... 9

8. REMOVABLE TERMINAL PLUG CONNECTION .................................. 10

9. PROTECTION OPERATION LIST ............................................................... 11

10. TAMPER-PROOF CAP ATTACHMENT .................................................... 11

11. CLEANING THE FILTER ................................................................................ 12

12. DIMENSIONAL DIAGRAM ............................................................................ 12

13. BLOCK DIAGRAMS

13.1. DA-250D .......................................................................................................... 13

13.2. DA-250DH ........................................................................................................ 13

14. SPECIFICATIONS

14.1. DA-250D CE301, DA-250D CE-GB, DA-250D CE-AU .................................... 14

14.2. DA-250DH CE301, DA-250DH CE-GB, DA-250DH CE-AU ............................ 15

3

When Installing the Unit

• Do not expose the unit to rain or an environment
where it may be splashed by water or other liquids,
as doing so may result in fire or electric shock.

• Use the unit only with the voltage specified on the
unit. Using a voltage higher than that which is
specified may result in fire or electric shock.

• Do not cut, kink, otherwise damage nor modify the
power supply cord. In addition, avoid using the
power cord in close proximity to heaters, and never
place heavy objects -- including the unit itself -- on
the power cord, as doing so may result in fire or
electric shock.

• Be sure to replace the unit's terminal cover after
connection completion. Because the voltage of up
to 100 V is applied to the high impedance speaker
terminals, never touch these terminals to avoid
electric shock. (DA-250DH only)

• External wiring connected to the terminals marked
with requires installation by an instructed person.

(DA-250DH only)

• The apparatus shall be connected to a mains
socket outlet with a protective earthing connection.

When the Unit is in Use

• Should the following irregularity be found during
use, immediately turn off this unit's power switch,
disconnect the power supply plug from the AC
outlet and contact your nearest TOA dealer. Make
no further attempt to operate the unit in this
condition as this may cause fire or electric shock.

· If you detect smoke or a strange smell coming

from the unit.

· If water or any metallic object gets into the unit

· If the unit falls, or the unit case breaks

· If the power supply cord is damaged (exposure of
the core, disconnection, etc.)

· If it is malfunctioning (no tone sounds.)

• To prevent a fire or electric shock, never open nor
remove the unit case as there are high voltage
components inside the unit. Refer all servicing such
as modification inside the unit to qualified service
personnel.

• Do not place cups, bowls, or other containers of
liquid or metallic objects on top of the unit. If they
accidentally spill into the unit, this may cause a fire
or electric shock.

• Do not insert nor drop metallic objects or flammable
materials in the ventilation slots of the unit's cover,
as this may result in fire or electric shock.

• Do not touch a plug during thunder and lightning,
as this may result in electric shock.

When Installing the Unit

• Never plug in nor remove the power supply plug
with wet hands, as doing so may cause electric
shock.

• When unplugging the power supply cord, be sure to
grasp the power supply plug; never pull on the cord
itself. Operating the unit with a damaged power
supply cord may cause a fire or electric shock.

• When moving the unit, be sure to remove its power
supply cord from the wall outlet. Moving the unit
with the power cord connected to the outlet may
cause damage to the power cord, resulting in fire or
electric shock. When removing the power cord, be
sure to hold its plug to pull.

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe
operation.

• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.

• After reading, keep this manual handy for future reference.

Safety Symbol and Message Conventions

Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.

WARNING

Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.

Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.

WARNING

CAUTION

CAUTION

4

• Avoid installing the unit in humid or dusty locations,
in locations exposed to the direct sunlight, near the
heaters, or in locations generating sooty smoke or
steam as doing otherwise may result in fire or
electric shock.

• To avoid electric shocks, be sure to first turn off this
unit's power switch when connecting speakers.

• The unit is designed exclusively to be mounted in
an equipment rack. Be sure to follow the
instructions below when rack-mounting the unit.
Failure to do so may cause a fire or personal injury.

· Install the equipment rack on a stable, hard floor.

Fix it with anchor bolts or take other arrangements
to prevent it from falling down.

· The supplied rack-mounting screws can be used

for the TOA equipment rack only. Do not use
them for other racks.

· When installing the unit in a rack other than that

of TOA, be sure to use the screws with a
diameter of over 5 mm and length of over 12 mm
to mount the unit.

· When connecting the unit's power cord to an AC

outlet, use the AC outlet with current capacity
allowable to the unit.

When the Unit is in Use

• Make sure to set all input level controls to ∞(infinity)
position before power is switched on.
Loud noise produced when power is switched on
with any of those controls set to the position other
than ∞position can impair hearing.

• Do not operate the unit for an extended period of
time with the sound distorting. Doing so may cause
the connected speakers to heat, resulting in a fire.

• Contact your TOA dealer as to the cleaning. If dust
is allowed to accumulate in the unit over a long
period of time, a fire or damage to the unit may
result.

• If dust accumulates on the power supply plug or in
the wall AC outlet, a fire may result. Clean it
periodically. In addition, insert the plug in the wall
outlet securely.

• Turn off this unit's power switch, and unplug the
power supply plug from the AC outlet for safety
purposes when cleaning or leaving the unit unused
for 10 days or more. Doing otherwise may cause a
fire or electric shock.

2. GENERAL DESCRIPTION

TOA's DA-250D and DA-250DH Dual Power Amplifiers feature high power handling capabilities and durability.
The DA-250D is configured with 250 W x 2 channels (4 Ω output) and 170 W x 2 channels (8 Ω output), and
the DA-250DH features a 250 W x 2 channels (100 V line, 40 Ω output) configuration. Besides, the DA-250D's
output is made available for bridge connection, allowing it to be used as a 500 W (8 Ω) monaural amplifier.
Their wide range of applications include stores and permanent sound systems.

3. FEATURES

• 1U rack mounting size*.

• Low power consumption and light weight.

• An input signal to Channel 1 can be routed to both channels 1 and 2, and the output level adjusted using the
input level control for each channel.

• Electronically-balanced inputs.

• Input terminals employ removable terminal blocks and XLR type connectors to provide maximum connection
ease.

• Equipped with the LED indicators that show the input/output status, etc.

• Built-in protection circuitry disconnects the power amplifier's output from the load when a short circuit,
overload, or unusual temperature rise occurs.

* 1U size = 44.5 mm (reference size)

The lighting flash with arrowhead symbol,
within an equilateral triangle, is intended
to alert the user to the presence of
uninsulated "dangerous voltage" within
the product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.

5

4. HANDLING PRECAUTIONS

• Keep the input cable away from the output cable. If installed close to each other, oscillation could occur.

• To avoid unit failures, never connect outputs of two or more channels in parallel.

• Only connect speakers with an impedance equal to or greater than those specified. Connecting speakers
with a smaller impedance than specified could cause damage to the unit.

• Periodically clean the filter located inside the ventilation panel on the unit's front panel. If the filter becomes
clogged, heat will become trapped inside the enclosure.

• Install the unit in locations where the temperature is between –10 and +40°C and the moisture is less than
90%RH (no dew condensation must be formed).

• To clean, be sure to first turn off this unit's power switch, then wipe with a dry cloth. When the unit gets very
dirty, use a cloth damped in a neutral cleanser. Never use benzene, thinner, alcohol, or chemically-treated
cleaning cloth because such volatile liquids could deform or discolor the unit.

• The fan is a consumable product. As a guideline, we recommend that it be replaced with a new one when its
total operating time reaches approximately 20000 hours (when used in ambient temperatures of
approximately 25°C).

Note: The above figure is simply a guideline, and does not guarantee the fan’s operating life. Since

broadcasts from the digital power amplifier could be disabled if the fan malfunctions, the fan requires
regular inspection and maintenance. For maintenance service, please contact the dealer from whom
the digital amplifier was purchased.

5. INSTALLATION PRECAUTIONS

• The supplied power supply cord is designed for exclusive use with this unit. Never use it with other
equipment.

• When mounting the unit in an equipment rack, the inside of the rack must be sufficiently ventilated.
To achieve sufficient ventilation, remove all panels on the rear of the rack.

• When mounting the unit in the rack, also mount a Perforated Panel larger than 1U in size*:

(1) at the top and the bottom of the rack, and
(2) above and below every 5 units.

• Robust structure is one of the unit's main features. However, if the strength is particularly needed when
installing the unit in the rack, use a supporting runner for the safety purposes.

* 1U size = 44.5 mm (reference size)

The supplied rack-mounting screws can be used for the TOA equipment
rack only. Do not use them for other racks.
When installing the unit in a rack other than that of TOA, be sure to use
the screws with a diameter of over 5 mm and length of over 12 mm to
mount the unit.
Failure to do so may cause personal injury.

CAUTION

Power amplifiers

Power amplifiers

(5 units)

(5 units)

Perforated panel

6

1. Power switch [ ON / OFF]

Turning this switch on causes the amplifier to
function, and turning it off causes the amplifier to
cease function.

Note: The unit is not completely disconnected

from the power supply even if this Power
switch is turned off.

2. Power indicator [POWER]

Lights blue when the Power switch (1) is turned
on.

3. Input level controls [CH 1 (BRIDGE), CH 2]

Adjust the input level of each channel.
Turn the control clockwise to increase the input
level and counterclockwise to decrease the level.

4. Ventilation panel (Air Vent)

A filter is located inside the ventilation panel.
To clean the filter, remove the ventilation panel.
(See p. 12; Cleaning the Filter.)

5. Indicators [INPUT, OUTPUT, PEAK, PROTECT]

The indicators are as follows from left to right:

• Input indicator [INPUT]

Lights green regardless of the input level control
setting when an input signal level exceeds about
–20 dB.

• Output indicator [OUTPUT]

Lights yellow when an output level exceeds
about 1 W at an 8 Ω load (DA-250D) or 40 Ω
load (DA-250DH).

• Peak indicator [PEAK]

Lights red when an output signal clips (distortion
occurs).

Note

When the Peak indicator lights, turn the input
level control (3) counterclockwise until its light
extinguishes or decrease the input signal level of
the connected external device.
Operating the unit while the Peak indicator
remains lit may cause the protection circuitry to
be activated.

• Protection indicator [PROTECT]

Lights red when the protection circuitry is
activated. (See p. 11; Protection Operation List.)
When the power is switched on, this indicator
lights for about 2 seconds and then extinguishes.

When a bridge connection is made
(DA-250D only)

When Channels 1 and 2 are bridge-connected
(BRIDGE ON/OFF switch (9) is set to ON), the
CH 1/BRIDGE level control adjusts the input
levels of Channels 1 and 2.
In this event, the CH 2 level control cannot be
used.

6. NOMENCLATURE AND FUNCTIONS

[Front]

DA-250D

1243 5

3

DA-250DH

5

124

7

[Rear]

6. AC inlet

Connect the supplied power cord to this inlet.
The socket-outlet shall be installed near the
equipment and the plug (disconnecting device)
shall be easily accessible.

7. Functional ground terminal [SIGNAL GND]

Hum noise may be generated when external
equipment is connected to the unit. Connecting
this terminal to the functional ground terminal of
the external equipment may reduce the hum
noise.

Note

This terminal is not for protective earth.

8.

Speaker output terminals (with a terminal cover)
[OUTPUTS (DA-250D), OUTPUTS 100V (DA-250DH)]

Connect speaker cables to these terminals.

9. BRIDGE ON/OFF switch (DA-250D only)
[BRIDGE, ON / OFF]

Used when bridge-connecting the unit's
Channels 1 and 2.
(See p. 8; Settings and Connections.)

• 2-channel output mode

Set BRIDGE switch to OFF. (factory-preset)

• 1-channel output mode

Set BRIDGE switch to ON.

Note

Be sure to first turn off the Power switch (1)
when changing these switch settings.

10. CH 1 mode ON/OFF switch
[PARALLEL, ON / OFF]

Setting this switch to ON transmits the Channel 1
input signal to both channels 1 and 2. (PARALLEL
mode)
Note that output signal levels can be individually
adjusted with each channel's Input level control
(3).
Setting this switch to OFF (factory-preset)
transmits each channel's input signal to each
corresponding channel. (STEREO mode)

Note

Be sure to first turn off the Power switch (1)
when changing this switch setting.

11. Input terminals [INPUTS]

Electronically-balanced input terminals.
Each removable terminal block (3 pins) is
internally connected in parallel to the
corresponding XLR type connector.

• Removable terminal block (3 pins)

H: Hot, C: Cold, E: Earth

•

XLR type male connector (XLR-3-31 equivalent)

Pin 1: Earth, Pin 2: Hot, Pin 3: Cold

If a straight plug hits the rack's rear cover or
wall behind the rack when it is used for
connection, use the L-shaped plug instead.

Caution when using an XLR type plug

DA-250D

DA-250DH

6

7 9 10

6

7 10

8

8

11

11

8

Step 1. Turn off this unit's Power switch.

Step 2. Set the BRIDGE ON/OFF switch (DA-250D only) and CH 1 mode ON/OFF switch.

Step 3. Connect the sound source equipment to the Input terminals.

Note: Refer to p. 10 for the removable terminal plug connection.

Step 4. Connect speakers to the Speaker output terminals.

4-1. Unscrew the output terminal cover.

4-2. Strip 10 mm of insulative jacket from the end of the speaker cable,

as shown in the figure at right.

4-3. Connect speaker cables to the output terminals.

4-4. Replace the output terminal cover in place.

Be sure to replace the unit's terminal cover after connection completion.
Because high voltage is generated at the speaker output terminals,
never touch these terminals to avoid electric shock. (DA-250DH only)

WARNING

7.1.1. When using the DA-250D

7. SETTINGS AND CONNECTIONS

7.1. Switch Settings and Speaker Connections

[Rear panel]

CH 1 mode ON/OFF switchBRIDGE ON/OFF switch

(DA-250D only)

Speaker output terminals

(with a terminal cover)

Input terminals

Note: The figure shows the DA-250D.

10 mm

[2 inputs - 2 outputs] (factory-preset)

CH1

CH1

CH2

CH2

Switch

BRIDGE

CH 1 mode

Setting

OFF

OFF

Speaker output terminals

CH2 CH1

4 – 8 Ω

4 – 8 Ω

9

7.1.2. When using the DA-250DH

[1 input - 2 outputs]

CH1

CH1

CH2

Switch

BRIDGE

CH 1 mode

Setting

OFF

ON

Speaker output terminals

CH2 CH1

4 – 8 Ω

4 – 8 Ω

[1 input - 1 output]

CH1

CH1

CH2

[2 inputs - 2 outputs] (factory-preset)

CH1

CH1

CH2

CH2

Speaker output terminals

Switch

BRIDGE ON

Setting

Note

Channel 1 input signal is output regardless
of the CH1 mode ON/OFF switch setting.

Speaker output terminals

Switch

CH 1 mode OFF

Setting

CH2 CH1

BRIDGE

8 Ω

40 Ω

[1 input - 2 outputs]

CH1

CH1

CH2

Switch

CH 1 mode ON

Setting

40 Ω

Speaker output terminals

CH2 CH1

40 Ω

40 Ω

10

Connector connections

Step 1. Loosen the terminal screw, then insert the cable.

Step 2. Retighten the terminal screw. (Pull on the cable to ensure it is securely connected.)

Tip

Recommended slotted screwdriver type: Screwdriver with blade that is 3 mm in width

8. REMOVABLE TERMINAL PLUG CONNECTION

Cautions

• Be sure to use shielded cables for audio signal lines.

• Avoid soldering cable conductor, as contact resistance may increase when the cable is tightened and the
solder is crushed, possibly resulting in an excessive rise in joint temperatures.

• Use cables of AWG 12 – 24.

Cable end treatment

Shielded cable

7 mm

20 mm

Slotted screwdriver

Tightens Loosens

2

1

Hot

Earth

Cold

Shielded cable

1

Terminal screw

Removable terminal plug

Bit shape 3 mm

11

10. TAMPER-PROOF CAP ATTACHMENT

To protect the input level control from accidental operation, it is recommended to replace the control knob with
the supplied tamper-proof cap as illustrated.

9. PROTECTION OPERATION LIST

Failure Protection Operation Indicator Remedy Recovery

Overcurrent due
to overload

Short circuit Current limiter activated.

Temperature rise
at power amp.
heat sink
(over 100°C)

Temperature rise
inside the unit
(over 80°C)

Abnormal DC
voltage output

Current limiter activated
when impedance drops
below the specified
value.

Load is disconnected.

Load disconnected. Protection indicator

Built-in amplifier unit
that caused the failure
halted.

Load disconnected. Protection indicator

Peak indicator lights. Remove overload. Connecting a correct load

Protection indicator
lights.

lights.

Four indicators of
the corresponding
channel extinguish.

lights.

automatically restores
normal operation.

Check speakers and
lines for short circuit.

Check the unit for
correct ventilation and
overload.

Contact the TOA dealer where the unit was
purchased.

Turn off this unit's Power
switch. Correct the load,
then turn on the power.

Operation automatically
returns to normal when
the temperature decreases.

Input level control

Tamper-proof cap (accessory)

12

11. CLEANING THE FILTER

Step 1. Turn off this unit's Power switch.

Step 2. Remove the ventilation panel as shown in the figure.

Step 3. Detach the filter inside the ventilation panel.

Step 4. Clear the filter of dust.

Step 5. Replace the filter and ventilation panel.

12. DIMENSIONAL DIAGRAM

Unit: mm

Ventilation Panel

2

3

Filter

Ventilation Panel

442

Detach the panel by pressing on the left or right side.

371 22.5

401.8

465

482

31.8

44

13

13. BLOCK DIAGRAMS

13.1. DA-250D

13.2. DA-250DH

CH 1 INPUT

H
C
E

HE

C

CH 2 INPUT

H
C
E

HE

C

PARALLEL
switch

CH 1 INPUT

H
C

E

HE

C

CH 2 INPUT

H
C

E

HE

C

PARALLEL
switch

CH 1
input level
control

CH 2
input level
control

CH 1
input level
control

CH 2
input level
control

+4 dB

-

CH 1 sensitivity
selection jumper
(+4 dB/

-

10 dB)

+4 dB

-

CH 2 sensitivity
selection jumper
(+4 dB/

-

10 dB)

CH 1 sensitivity
selection jumper
(+4 dB/

-

10 dB)

CH 2 sensitivity
selection jumper
(+4 dB/

-

10 dB)

10 dB

10 dB

+4 dB

-

10 dB

+4 dB

-

10 dB

ON

OFF

BRIDGE ON/OFF
switch

Current Limiter

Short Detector

Protection Circuit

Current Limiter

Short Detector

Protection Circuit

Current Limiter

Short Detector

Protection Circuit

Current Limiter

Short Detector

Protection Circuit

OUTPUT 1

relay

OUTPUT 2

relay

OUTPUT 1

relay

OUTPUT 2

relay

CH 1
OUTPUT

+

-

+

-

CH 2
OUTPUT

+

CH 1

-

OUTPUT

+

CH 2

-

OUTPUT

BRIDGE
OUTPUT

14

220 – 240 V AC, 50/60 Hz

Class D

120 W (based on EN standards)
620 W (rated output 4 Ω x 2)
400 W (rated output 8 Ω x 2)

2 circuits, +4 dB* (1.23 V, input level control in maximum position),
10 kΩ, electronically-balanced, removable terminal block (3 pins),
XLR-3-31 type connector
CH 1 mode ON/OFF switch (ON: PARALLEL, OFF: STEREO)

2 channels: 250 W x 2 (4 Ω), 170 W x 2 (8 Ω)
1 channel (BRIDGE): 500 W (8 Ω)
M4 screw terminal, distance between barriers: 8.8 mm

20 – 20,000 Hz (±1 dB)

0.1% (1 kHz), 0.3% (20 – 20,000 Hz)

Protection against excessive current flow due to overload,
short circuit, unusual DC voltage output,
temperature rise at power amp. heat sink (over 100°C),
temperature rise inside the unit (over 80°C)

100 dB (A-weighted)

70 dB (A-weighted)

Power (blue) x 1, Input (green) x 2, Output (yellow) x 2, Peak (red) x 2,
Protect (red) x 2

Forced air cooling

–10°C to +40°C

Under 90%RH (no condensation)

Panel: Aluminum, black, alumite
Case: Plated steel sheet

482. (w) x 44 (h) x 401.8 (d) mm

5.3 kg

Power Source

Amplification system

Power Consumption

Input

Rated Output

Frequency Response

Total Harmonic Distortion

Protection Circuit

S/N Ratio

Crosstalk

LED Indicator

Cooling

Operating Temperature

Operating Humidity

Finish

Dimensions

Weight

14. SPECIFICATIONS

* 0 dB = 0.775 V

Note: The design and specifications are subject to change without notice for improvement.

Power cord (2 m) ................................................................. 1

Removable terminal plug (3 pins) ........................................ 2

Rack mounting screw (with plain washer) 5 x 12 ................ 4

Tamper-proof cap ................................................................ 2

• Accessories

14.1. DA-250D CE301, DA-250D CE-GB, DA-250D CE-AU

15

* 0 dB = 0.775 V

Note: The design and specifications are subject to change without notice for improvement.

Power cord (2 m) ................................................................. 1

Removable terminal plug (3 pins) ........................................ 2

Rack mounting screw (with plain washer) 5 x 12 ................ 4

Tamper-proof cap ................................................................ 2

• Accessories

220 – 240 V AC, 50/60 Hz

Class D

120 W (based on EN standards)
580 W (rated output 100 V line, 40 Ω x 2)

2 circuits, +4 dB* (1.23 V, input level control in maximum position),
10 kΩ, electronically-balanced, removable terminal block (3 pins),
XLR-3-31 type connector
CH 1 mode ON/OFF switch (ON: PARALLEL, OFF: STEREO)

2 channels: 250 W x 2 (100 V line, 40 Ω)
M4 screw terminal, distance between barriers: 8.8 mm

50 – 20,000 Hz (–3 dB, +1 dB)

0.1% (1 kHz), 0.3% (100 – 20,000 Hz)

Protection against excessive current flow due to overload,
short circuit, unusual DC voltage output,
temperature rise at power amp. heat sink (over 100°C),
temperature rise inside the unit (over 80°C)

100 dB (A-weighted)

70 dB (A-weighted)

Power (blue) x 1, Input (green) x 2, Output (yellow) x 2, Peak (red) x 2,
Protect (red) x 2

Forced air cooling

–10°C to +40°C

Under 90%RH (no condensation)

Panel: Aluminum, black, alumite
Case: Plated steel sheet

482. (w) x 44 (h) x 401.8 (d) mm

5.3 kg

Power Source

Amplification system

Power Consumption

Input

Rated Output

Frequency Response

Total Harmonic Distortion

Protection Circuit

S/N Ratio

Crosstalk

LED Indicator

Cooling

Operating Temperature

Operating Humidity

Finish

Dimensions

Weight

14.2. DA-250DH CE301, DA-250DH CE-GB, DA-250DH CE-AU

133-22-239-9A

URL: http://www.toa.jp/

Traceability Information for Europe (EMC directive 2004/108/EC)

Manufacturer:

TOA Corporation
7-2-1, Minatojima Nakamachi, Chuo-ku, Kobe, Hyogo,
Japan

Authorized representative:

TOA Electronics Europe GmbH
Suederstrasse 282, 20537 Hamburg,
Germany