Toa C-CC764, C-CC714, C-CC564, C-CC514 User Manual

Download

Page 1

COMBINATION

DOME CAMERA SYSTEMS

C-RM500

Remote Controller

C-IF500

Interface Unit

C-AL80

Alarm Unit

Combination Dome Cameras

C-BC511A

Anchor Bracket

C-BC511U-S

Flush Ceiling Mounting Bracket (Smoked)

C-BC511W

Wall Mounting Bracket

C-BC511C-S

Ceiling Mount Cover (Smoked)

C-A711DM

Smoked Dome Cover

C-BC711W

Wall Mounting Bracket

C-BC511U

Flush Ceiling Mounting Bracket

C-BC511C

Ceiling Mount Cover

C-BC711PM

Pole Mounting Bracket

C-BC711P

Ceiling Suspension Bracket

C-BC511P

Ceiling Suspension Bracket

Brackets and Cover

For Outdoor Use For Indoor Use

Controller and Units

C-CC764

multi function type

C-CC714

standard type

C-CC564

multi function type

C-CC514

standard type

For Outdoor Use For Indoor Use

with Ceiling Mount Cover C-BC511C

Page 2

Combination Dome Cameras

Configuring a perfect surveillance system.

■

Higher resolution delivers better images.

TOA cameras now feature a higher horizontal resolution of 480 lines (NTSC) to deliver images of enhanced quality.

■

All points coverage at high speed.

TOA's new combination dome cameras help to improve monitoring environments with an ideal coverage area that is made possible with a 360° rotation range to cover any possible position. Capable of a maximum rotating speed (panning/tilting) of 360°/second, these versatile cameras allow rotation speed to be slowed down as desired.

■

Expanded zooming ability.

TOA cameras are capably equipped for zooming as needed. C-CC564 and C-CC764 incorporate a 23X ultra wide-angle zoom lens for better coverage of a desired image. If even more zooming is required, 12X digital zooming can be activated, resulting in an extraordinary combined zoom factor of up to an 276X*.

*C-CC564 and C-CC764 cameras are equipped with a high-speed,

wide-angle lens having a 23X zoom while C-CC514 and C-CC714 cameras are equipped with a high-speed, wide-angle lens having a 22X zoom. With the 12X digital zoom activated, a total 276X zoom is possible for C-CC564 and C-CC764 cameras and 264X zoom for C-CC514 and C-CC714 cameras.

■

Intelligent image optimizing using the Wide Dynamic Range function.*

If the area of coverage exhibits varying brightness levels, it causes various problems that prevent achieving superb image quality. These problems pose severe difficulties for cameras that utilize conventional technology for dealing with brightness variations. The following two examples illustrate the problem.

■

Sophisticated autofocus modes add versatility.

TOA cameras are equipped with advanced auto-focusing. Three independent modes are offered: Auto focus for normal operation is activated with a single push. Stop Auto Focus activates if the camera view or viewing angle changes. To keep auto focus working continuously, the Continuous auto focus can be engaged.

■

Motion detection function initiates operation.*

Incorporated into the C-CC564 and C-CC764 are a motion detection function. When a moving object enters a camera's field of view, the camera will initiate a preprogrammed operation or a series of operations. The camera's view can be monitored onscreen with a window that is divided into 64 segments and from these, eight 8 areas can be selected as motion detection zones.

■

Image clarity maintained for day and night

with sensitivity boost.

In night or dark lighting conditions, the camera's shutter speed is automatically reduced so that more light can enter. This function effectively increases the camera's sensitivity so that dark areas can be made up to 32 times brighter.

■

B/W mode improves low light performance.*

Combination dome cameras also incorporate a separate B/W mode. At night, as light intensity decreases, this mode automatically activates, boosting camera sensitivity and making it possible to capture clear images even in unsatisfactory light conditions. When light conditions are satisfactory, the camera will revert to its primary function as a color camera. Used together, the sensitivity boost and B/W modes allow TOA combination dome cameras to efficiently function for 24-hour monitoring.

Note: B/W mode allows monitoring target areas that are not possible

in normal light conditions.

360˚

However, setting the focus on the indoors now "whites out" the outdoor area. (Photo B)

Placing the focus on the outdoors results in the indoors being too dark to see well. (Photo A)

TOA Combination Dome Cameras incorporate a special Digital Signal Processor (DSP) that works to optimize image, producing a single image of exceptional clarity that is comparable to the same image when viewed with human eyes.

B/W mode.

(color image)

(B/W image)

Sensitivity boost allows cameras to provide good color image quality for dark areas.

Page 3

FEATURES

■

Protecting user privacy.

a) Privacy Masking function.*

Depending on system use requirements, there may be several areas that the system administrator decides does not require surveillance for whatever reason. Users are allowed to select in advance the locations they wish to be excluded from surveillance in a camera's field of view. Onscreen selected areas can be masked with a rectangle and a maximum of 8 areas (a single screen can have 2 masked areas) can be masked for privacy.

b) Restricting camera movement.

In addition to masking areas for privacy, a hardware-oriented method is also available. A camera's rotation range in both horizontal and vertical directions can be restricted to exclude areas from surveillance.

■

Outdoor installation ready. (meets IP66 standards)

C-CC714 and C-CC764 utilize a waterproof and dustproof design that fully conforms to IP66 standards and can be safely installed outdoors. Cameras are cased in a special housing that withstands outdoor conditions, allowing them to be installed outdoors, even if the location is directly exposed to rain.

■

Withstands cold weather conditions.

C-CC714 and C-CC764 incorporate a heating circuit that allows operation in severe temperatures down to –40°C. Heating is automatically turned on when ambient temperatures go below 0°C and will automatically switch off when the temperatures rise.

Note: Turning the camera on if the camera interior is below 0°C may not result in producing an immediately viewable image. Once the camera interior temperature rises above 0°C, images will be viewable.

■

Route tracing facilitates subject monitoring.

In order to make it easy to follow a subject along a route, the camera can be set to automatically monitor preset points for up to 60 seconds. Two different routes can be programmed.

■

Configuring programmable tours.

Through combinations of the 255 preset positions and trace function, a camera can be programmed to automatically and continuously repeat a travel pattern as a tour. Up to 16 tour patterns can be programmed. Any tour program is able to have a different travel pattern that can be activated by an alarm input or timer.

■

Programmable camera operation initiated by alarm input.

A useful Alarm function allows programming camera operation that can be activated by an alarm input. Desired camera operations such as position replay, touring, tracing, and control of the auxiliary terminal can be programmed to activate when the camera receives an alarm input. Each camera is equipped with three (C-CC564 has eight) alarm inputs and each alarm input can be set to respond with different preprogrammed operation.

■

Preset operation start with Timer program function.

A camera can conveniently be set to begin operation at a preset time with an builtin timer. Each camera has a clock function that can be set to initiate operation at a preset time. The timer can be set for a specific date, day of the week, or daily. Up to 16 different timer programs can be set.

■

Software for maintenance.

TOA cameras include dedicated software that allows easy titles to be set and to create a backup of parameters with a PC.

■

Flexible installation options.

TOA cameras can easily be installed on ceilings, walls or on poles thanks to the wide range of mounting brackets available.

■

Titling options.

To facilitate camera use, various titles can be input and displayed on the monitor. In addition to camera and position titles, other titles for display include trace title, displayed while the trace function is on, tour title, displayed when tour function is activated, and alarm title displayed when an alarm input is received.

■

Other functions.

• Tilt (vertical) range: +5° — –185°.*

•Auto flip function*

• Rotation speed can be varied to match lens zooming ratio in manual operation mode.

• Freeze preset function*

Displays the still image during camera movement between preset positions.

• Flicker-free operation

• The camera is equipped with 3 (C-CC564 has 8) alarm inputs and 1 auxiliary contact output.

• RS-485 protocol control.

Function Comparison Chart

C-CC514 C-CC564 C-CC714 C-CC764

Minimum Illumination 1 lx (50 IRE) 3 lx (50 IRE) 1 lx (50 IRE) 3 lx (50 IRE)

(High-Sensitivity: OFF)

0.3 lx (20 IRE) 1 lx (20 IRE) 0.3 lx (20 IRE) 1 lx (20 IRE)

Wide Dynaic Function — ● — ●

B/W Mode Function — ● — ●

Optical Zooming 22x 23x 22x 23x

Zoom Speed (WIDE end to TELE end)

(preset operation) Approx. 1.3s Approx. 1.6s Approx. 1.3s Approx. 1.5s

(manual operation) Approx. 2.4s Approx. 2.9s Approx. 2.4s Approx. 2.9s

Rotating Range

(Tilting)

+5° to – 95° +5° to – 185° +5° to – 90° +5° to –185°

Operating Temperature –10˚C to +50˚C –40˚C to +50˚C

Dust/Water Capability —— IP66

Auto Flip Function — ● — ●

Freeze Preset Function — ● — ●

Privacy Mask Function

—

Up to 8

—

Up to 8

(up to 2 each frame) (up to 2 each frame)

Motion Detection Function

— ● — ●

*C-CC764 and C-CC564 only

Page 4

C-CC764/C-CC-714

COMBINATION DOME CAMERA (OUTDOOR USE)

C-CC714

SPECIFICATIONS

Power source 24V AC 50/60Hz (2P loose end) Power consumption 10W (normal operation), 80W max. Control RS-485 communications system (new protocol compatible) Video Output VBS 1.0V(p-p), 75Ω, BNC-R jack Camera Control Terminal RS-485 camera control connector, multi-pair cable 8P, loose end (3P of 8P) Alarm Input 3 channels, no-voltage make contact input, open voltage: 18V DC,

short-circuit current; Under 2mA (settable alarm action), multi-pair cable 8P, loose end (3P of 8P)

Auxiliary Contact Output 1 channel, open collector output, withstand voltage: 30V DC,

permissible current: Under 100mA, multi-pair cable 8P, loose end (1P of 8P)

Synchronization Internal synchronization/power synchronization

(phase adjustable when in power synchronization mode)

ID 8 characters (alphanumeric and symbols)

Camera, Position, Trace, Auto-pan, Tour, Home, Alarm, Sector, AUX

No. of Preset Positions 255 Positions Automatic Operation Auto-pan, Preset sequence, Auto-trace (2 preset patterns (60s)), Tour (16 preset patterns) Timer Refresh: Starts at the preset time every day or every week by timer settings

Program: Settable 16 actions

Camera Image device 1/4 type CCD Resolution Horizontal: 480 lines (at center) S/N ratio 50dB Minimum Illumination High-sensitivity function 0FF: 1 lx (50 IRE), 0.3 lx (20 IRE)

High-sensitivity function 0N: 0.03 lx (50 IRE), 0.01 lx (20 IRE)

Backlight Compensation Pattern 1/Pattern 2/Pattern 3/OFF High-Sensitivity Function Slow shutter mode (32 times max.) White Balance ATW/ AWB Flicker Reduction Automatic correction Electronic Zooming 12x zooming Auto-Focus One push/stop AF/continuous Lens Zooming 22x Effective Focal Length f = 4.0 – 88mm (22X) Effective Angle of View Horizontal: 47.3° (W) – 2.2° (T), Vertical: 36.5° (W) – 1.7° (T) Maximum Aperture F 1.6 (W) – F 3.8 (T) Zoom Speed WIDE end to TELE end

Approx. 1.3s (preset operation), Approx. 2.4s (manual operation)

Pan/Tilt Head Rotating Range Panning: Endless 360° rotation, Tilting: +5° to –90° Rotating Speed Panning/Tilting: 360°/s max. (preset operation), 360°/s max. (manual operation)

Other Function Manual Limit Operating Temperature –40˚C to +50˚C Operating Humidity Under 90% RH (no due condensation produced) Application Indoors and outdoors (except seaside, industrial districts and locations exposed to fine particles,

where the unit is subject to corrosion, and heights that expose the unit to strong wind pressure)

Dust/Water Protection IP66 Finish Case, top cover and decorative frame: PC resin, light gray

Sunshade: Aluminum, light gray, paint Dome cover: PC resin (transparent)

Dimensions Camera section external diameter: ø230

330.5 (H)mm

Dome external diameter: ø 150mm

Weight 3.9kg Accessory

Top cover mounting screw (Hexagon socket screw M4 × 8) × 3, CD-R (Camera controller software, manual (PDF)) × 1

Option Wall mounting bracket: C-BC711W, Suspension bracket: C-BC711P,

Pole mounting bracket: C-BC711PM, Smoked dome cover: C-A 711DM

C-CC764

SPECIFICATIONS

short-circuit current; Under 2mA (settable alarm action), multi-pair cable 8P, loose end (3P of 8P)

Auxiliary Contact Output 1 channel, open collector output, withstand voltage: 30V DC,

permissible current: Under 100mA, multi-pair cable 8P, loose end (1P of 8P)

Synchronization Internal synchronization/power synchronization

(phase adjustable when in power synchronization mode)

ID 8 characters (alphanumeric and symbols)

Camera, Position, Trace, Auto-pan, Tour, Home, Alarm, Sector, AUX

Program: Settable 16 actions

Camera Image device 1/4 type CCD Resolution Horizontal: 480 lines (at center) S/N ratio 50dB Minimum Illumination High-sensitivity function 0FF: 3 lx (50 IRE), 1 lx (20 IRE)

High-sensitivity function 0N: 0.03 lx (50 IRE), 0.01 lx (20 IRE)

Backlight Compensation WIDE DYNAMIC/Pattern 1/Pattern 2/Pattern 3/OFF Dynamic Range 46dB (backlight compensation: WIDE DYNAMIC operation) High-Sensitivity Function B/W mode and slow shutter mode (32 times max.) White Balance ATW/ AWB Flicker Reduction Automatic correction Electronic Zooming 12x zooming Auto-Focus One push/stop AF/continuous Lens Zooming 23x Effective Focal Length f = 3.6 – 82.8mm (23X) Effective Angle of View Horizontal: 54° (W) – 2.5° (T), Vertical: 41.6° (W) – 1.9° (T) Maximum Aperture F 1.6 (W) – F 3.7 (T) Zoom Speed WIDE end to TELE end

Approx. 1.5s (preset operation), Approx. 2.9s (manual operation)

Pan/Tilt Head Rotating Range Panning: Endless 360° rotation, Tilting: +5° to –185° Rotating Speed Panning/Tilting: 360°/s max. (preset operation), 360°/s max. (manual operation)

Other Function Auto-Pan, Freeze Preset, Manual Limit, Privacy Masking (up to 8),

Motion Detect (each 8 presets at each 4 positions)

Operating Temperature –40˚C to +50˚C Operating Humidity Under 90% RH (no due condensation produced) Application Indoors and outdoors (except seaside, industrial districts and locations exposed to fine particles,

where the unit is subject to corrosion, and heights that expose the unit to strong wind pressure)

Dust/Water Protection IP66 Finish Case, top cover and decorative frame: PC resin, light gray

Sunshade: Aluminum, light gray, paint Dome cover: PC resin (transparent)

Dimensions Camera section external diameter: ø230

330.5 (H)mm

Dome external diameter: ø 150mm

Weight 3.9kg Accessory

Top cover mounting screw (Hexagon socket screw M4 × 8) × 3, CD-R (Camera controller software, manual (PDF)) × 1

Option Wall mounting bracket: C-BC711W, Suspension bracket: C-BC711P,

Pole mounting bracket: C-BC711PM, Smoked dome cover: C-A 711DM

• 255 preset positions

• 276X zoom (optical 23X, electronic 12X)

• Tilt rotation range +5° – -185° (using Auto-Flip function)

•Pan rotation range continuous 360°

• Pan/tilt maximum rotating speed is 360°/sec

• 1/4 type CCD image device

• 480 lines high resolution

• Wide dynamic range

•Autofocus

• High-sensitivity function (color and B/W modes)

• Preset sequency function

• Privacy masking function

• Restricting camera movement

•Auto-trace function

•Auto-tour function

• Motion detection function

•Auto-pan function

• Preset image freeze function

• Dust/Water Protection: IP66

• RS-485 protocol compatible

C-CC764

FEATURES

• 255 preset positions

• 264X zoom (optical 22X, electronic 12X)

• Tilt rotation range +5° – 90°

•Pan rotation range continuous 360°

• Pan/tilt maximum rotating speed is 360°/sec

• 1/4 type CCD image device

• 480 lines high resolution

•Autofocus

• High-sensitivity function (color mode)

• Preset sequency function

• Restricting camera movement

•Auto-trace function

•Auto-tour function

•Auto-pan function

• Dust/Water Protection: IP66

• RS-485 protocol compatible

C-CC714

FEATURES

Page 5

C-CC564/C-CC514

COMBINATION DOME CAMERA (INDOOR USE)

C-CC514

SPECIFICATIONS

Power source 24V AC 50/60Hz Power consumption 9W (normal operation), 19W max. (1.3A max.). Control RS-485 communications system (new protocol compatible) Video Output VBS 1.0V(p-p), 75Ω, BNC-R jack Camera Control Terminal RS-485 camera control connector Alarm Input 3 channels, no-voltage make contact input, open voltage: 18V DC,

short-circuit current; Under 2mA (settable alarm action)

Auxiliary Contact Output 1 channel, open collector output, withstand voltage: 30V DC,

permissible current: Under 100mA

Synchronization Internal synchronization/power synchronization

(phase adjustable when in power synchronization mode)

ID 8 characters (alphanumeric and symbols)

Camera, Position, Trace, Auto-pan, Tour, Home, Alarm, Sector, AUX

Program: Settable 16 actions

Camera Image device 1/4 type CCD Resolution Horizontal: 480 lines (at center) S/N ratio 50dB Minimum Illumination High-sensitivity function 0FF: 1 lx (50 IRE), 0.3 lx (20 IRE)

High-sensitivity function 0N: 0.03 lx (50 IRE), 0.01 lx (20 IRE)

Approx. 1.3s (preset operation), Approx. 2.4s (manual operation)

Pan/Tilt Head Rotating Range Panning: Endless 360° rotation, Tilting: +5° to –90° Rotating Speed Panning/Tilting: 360°/s max. (preset operation), 360°/s max. (manual operation)

Other Function Manual Limit Operating Temperature –10˚C to +50˚C (continuously active for operation at temperature below 0°C) Operating Humidity Under 90% RH (no due condensation produced) Application Indoor used Finish Base: PC/ABS resin, cool gray

Camera: PC/ABS resin, black

Dimensions ø168

234 (H)mm

Weight 1.7kg Accessory

Camera mounting screw × 4, Safety wire × 1, CD-R (Camera controller software, manual (PDF)) × 1

Option Ceiling mount cover: C-BC511C, C-BC511C-S

Flush ceiling mounting bracket: C-BC511U, C-BC511U-S Ceiling suspension bracket: C-BC511P Wall mounting bracket: C-BC511W Anchor bracket: C-BC511A

C-CC564

SPECIFICATIONS

Power source 24V AC 50/60Hz Power consumption 9W (normal operation), 19W max. (1.3A max.) Control RS-485 communications system (new protocol compatible) Video Output VBS 1.0V(p-p), 75Ω, BNC-R jack Camera Control Terminal RS-485 camera control connector Alarm Input 8 channels, no-voltage make contact input, open voltage: 18V DC,

short-circuit current; Under 2mA (settable alarm action)

Auxiliary Contact Output 2 channels, open collector output, withstand voltage: 30V DC,

permissible current: Under 100mA, relay contact output, permissible voltage: 110V DC, 125V AC, permissible current: Under 1A

Synchronization Internal synchronization/Power synchronization

(phase adjustable when in power synchronization mode)

ID 8 characters (alphanumeric and symbols)

Camera, Position, Trace, Auto-pan, Tour, Home, Alarm, Sector, AUX

Program: Settable 16 actions

Camera Image device 1/4 type CCD Resolution Horizontal: 480 lines (at center) S/N ratio 50dB Minimum Illumination High-sensitivity function 0FF: 3 lx (50 IRE), 1 lx (20 IRE)

High-sensitivity function 0N: 0.03 lx (50 IRE), 0.01 lx (20 IRE)

Approx. 1.5s (preset operation), Approx. 2.9s (manual operation)

Pan/Tilt Head Rotating Range Panning: Endless 360° rotation, Tilting: +5° to –185° Rotating Speed Panning/Tilting: 360°/s max. (preset operation), 360°/s max. (manual operation)

Other Function Auto-Pan, Freeze Preset, Manual Limit, Privacy Masking (up to 8),

Motion Detect (each 8 presets at each 4 positions)

Operating Temperature –10˚C to +50˚C (continuously active for operation at temperature below 0°C) Operating Humidity Under 90% RH (no due condensation produced) Application Indoor used Finish Base: PC/ABS resin, cool gray

Camera: PC/ABS resin, black

Dimensions ø168

234 (H)mm

Weight 1.7kg Accessory

Camera mounting screw × 4, Safety wire × 1, CD-R (Camera controller software, manual (PDF)) × 1

Option Ceiling mount cover: C-BC511C, C-BC511C-S

Flush ceiling mounting bracket: C-BC511U, C-BC511U-S Ceiling suspension bracket: C-BC511P Wall mounting bracket: C-BC511W Anchor bracket: C-BC511A

• 255 preset positions

• 276X zoom (optical 23X, electronic 12X)

• Tilt rotation range +5° – -185° (using Auto-Flip function)

•Pan rotation range continuous 360°

• Pan/tilt maximum rotating speed is 360°/sec

• 1/4 type CCD image device

• 480 lines high resolution

• Wide dynamic range

•Autofocus

• High-sensitivity function (color and B/W modes)

• Preset sequency function

• Privacy masking function

• Restricting camera movement

•Auto-trace function

•Auto-tour function

• Motion detection function

•Auto-pan function

• Preset image freeze function

• RS-485 protocol compatible

C-CC564

FEATURES

• 255 preset positions

• 264X zoom (optical 22X, electronic 12X)

• Tilt rotation range +5° – 90°

•Pan rotation range continuous 360°

• Pan/tilt maximum rotating speed is 360°/sec

• 1/4 type CCD image device

• 480 lines high resolution

•Autofocus

• High-sensitivity function (color mode)

• Preset sequency function

• Restricting camera movement

•Auto-trace function

•Auto-tour function

•Auto-pan function

• RS-485 protocol compatible

C-CC514

FEATURES

Page 6

Brackets and Dome Cover for C-CC764/C-CC-714 (Outdoor Use)

Brackets and Dome Cover for C-CC564/C-CC-514 (Indoor Use)

C-BC711P

Suspension Bracket

C-BC511A

Anchor Bracket

C-BC511C-S

Ceiling Mount Cover (Smoked)

The C-BC711P is exclusively designed to be used to suspend TOA's outdoor combination camera from a ceiling or eaves.

The C-BC711W is designed to be used to mount TOA's outdoor combination camera on a wall.

Finish Base: Aluminum, light gray, paint Pipe: Stainless steel (SUS304)

Dimensions 140 (W) × 164 (H) × 200 (D)mm Weight 1kg Accessory Camera mounting screw (M5×12, with washer) × 3

Note: pay attention to the strength of the attaching portion.

Finish Base: Aluminum, light gray, paint Pipe: Stainless steel (SUS304)

Dimensions 140 (W) × 240 (H) × 188.1 (D)mm Weight 1.3kg Accessory Camera mounting screw (M5×12, with washer) × 3

Note: pay attention to the strength of wall surface.

Transmissivity Approx. 30%* Finish Dome: PC resin, smoked

Frame: PC resin, light gray Dimensions ø219.8 × 128 (H)mm

(Dome external diameter: ø150mm)

Weight 400g

*As a general guideline, the minimum object illumination of the camera equipped with the

Smoked Dome Cover is approximately 3.3 times that of the camera without the cover.

Note: Be careful when installing the camera with this cover in low illumination location as the

cover may cause camera sensitivity to decrease.

C-BC711W

Wall Mounting Bracket

Finish Stainless steel (SUS304) Dimensions 140 (W) × 200 (H) × 60 (D)mm Weight 700g

Note: Reinforce the pole mounting bracket and mounting band separately for security when

installing the camera in locations exposed to vibration or strong winds. Maintenance the unit, mounting bracket and mounting band periodically to ensure that there are no loose joint nor rickety parts.

C-BC711PM

Pole Mounting Bracket

Finish Top cover: PC/ABS resin, cool gray Pipe: Stainless steel (SUS304) Bracket: Surface-treated steel plate, black, paint

Dimensions ø150 × 233mm Weight 1.2kg Accessory Top cover × 4, Safety wire × 1, Pattern paper × 1

Finish Top cover: PC/ABS resin, cool gray

Pipe: Stainless steel (SUS304) Bracket: Surface-treated steel plate, black, paint

Dimensions 150 (W) × 203 (H) × 203 (D)mm Weight 1.1kg Accessory Top cover × 4, Safety wire × 1, Paper pattern × 1

C-BC511C

Ceiling Mount Cover

Using the optional YS-60B and C-BC711W, the C-BC711PM can mount the outdoor combination camera on a pole.

C-A711DM

Smoked Dome Cover

The C-A711DM Smoked Dome Cover is specially designed to be used in conjunction with TOA's Combination Cameras. The Dome Cover is used to make it difficult for individuals to see the camera's orientation.

The C-BC511C-S is a camera installation cover designed solely for mounting TOA's Combination Cameras. The cover is used when

mounting the Combination camera directly to a ceiling or wall or suspending it from the ceiling. The cover is used to make it difficult for individuals to see the camera's orientation.

The C-BC511A is specially designed to

mount TOA's Combination Cameras directly on the wall. The bracket facilitates mounting of the camera on the plasterboard in the double ceiling or other locations where the mounting screws cannot be installed securely.

The C-BC511C is a camera installation cover designed solely for mounting TOA's Combination Cameras. The cover is used when

mounting the Combination camera directly to a ceiling or wall or suspending it from the ceiling. The cover is used to make it difficult for individuals to see the camera's orientation.

C-BC511P

Ceiling Suspension Bracket

C-BC511W

Wall Mounting Bracket

The C-BC511P is a Ceiling Suspension Bracket designed solely for suspending TOA's Combination Cameras from the ceiling.

C-BC511U

Flush Ceiling Mounting Bracket

C-BC511U-S

Flush Ceiling Mounting Bracket (Smoked)

The C-BC511U-S bracket is designed to be exclusively used for flush ceiling mounting of TOA's combination camera.

Use this bracket when mounting the camera to the ceiling surface where the fixing screws cannot be securely installed, such as on the plaster panel of the dual-construction ceiling. Also, use this bracket to minimize the exposure of the camera. The bracket is used to make it difficult for individuals to see the camera's orientation.

The C-BC511U bracket is designed to be exclusively used for flush ceiling mounting of TOA's combination camera. Use this bracket

when mounting the camera to the ceiling surface where the fixing screws cannot be securely installed, such as on the plaster panel of the dual-construction ceiling. Also, use this bracket to minimize the exposure of the camera.

Finish Case: PC/ABS resin, cool gray

Dome cover: Acrylic resin, transparent

Dimensions ø168 × 182.2 (H)mm

(Dome external diameter: ø125mm)

Weight 220g

Transmissivity Approx. 20%* Finish Case: PC/ABS resin, cool gray

Dome cover: Acrylic resin, smoked

Dimensions ø168 × 182.2 (H)mm

(Dome external diameter: ø125mm)

Weight 220g

*As a general guideline, the minimum object illumination of the camera equipped with the

Ceiling Mount Cover is approximately 5 times that of the camera without the cover.

Note: Be careful when installing the camera with this cover in low illumination location as the

cover may cause camera sensitivity to decrease.

Finish Bezel: PC/ABS resin, cool gray Dome cover: Acrylic resin, transparent Bracket: Aluminum, black, paint Surface-treated steel plate, black, paint

Dimensions ø250 × 282.7 (D)mm

(Dome external diameter: ø125mm)

Weight 1.2kg Accessory Safety wire × 1, Paper pattern × 1

Transmissivity Approx. 20%* Finish Bezel: PC/ABS resin, cool gray

Dome cover: Acrylic resin, smoked Bracket: Aluminum, black, paint Surface-treated steel plate, black, paint

Dimensions ø250 × 282.7 (D)mm

(Dome external diameter: ø125mm)

Weight 1.2kg Accessory Safety wire × 1, Pattern paper × 1

* As a general guideline, the minimum object illumination of the camera equipped with the

Flush Ceiling Mounting Bracket is approximately 5 times that of the camera without the bracket.

Note: Be careful when installing the camera with this bracket in low illumination location as the

cover may cause camera sensitivity to decrease.

Finish Sur face-treated steel plate, black, paint Dimensions 132 (W) × 30 (H) × 70 (D)mm Weight 1.1kg Accessory

Camera mounting screw × 4, Safety wire × 1, Paper pattern × 1

The C-BC511W Wall Mounting Bracket is specially designed to mount TOA's Combination Cameras to wall surfaces. Install the unit only in a location that can structurally support weight of the unit and camera.

Page 7

Combination Dome Camera

SETTING GUIDE

The camera menu screens are comprised of the following setting item screens.

PRESET SETTING

PRESET ID SETTING CAMERA AUTO MODE

CAMERA MENU

Setting Item

Programs the camera position (camera orientation), displays setting status, and performs reset.

ID (TITLE) SETTINGS

PRESET MEMORY*

Programs the camera position.

GLOBAL PRESET MEMORY CORRECTION

PRESET MEMORY RESET

Resets preset camera position.

DISPLAY

Sets the title.

ID SETTINGS*

Sets ID.

Sets the origin point of the angle display.

Sets to display or hides the title.

DISPLAY POSITION SETTINGS*

CAMERA SETTINGS

Sets camera properties.

WHITE BALANCE*

Sets the camera's white balance.

BACKLIGHT COMPENSATION*

Sets the backlight compensation.

BRIGHTNESS*

Adjusts the camera's brightness.

DAY AND NIGHT*2 *

FRAME ADJUSTMENT SETTINGS

Sets title display position and its length.

ANGLE ORIGIN POINT SETTING

Sets the character display position.

TRACE 2 PAUSE TIME

TOUR

Sets the operation to be programmed.

AUTOMATIC OPERATION

Sets automatic operation of Auto-Pan, Preset sequence, Trace and Tour.

AUTO KEY

Assigns automatic functions to the Auto key.

AUTO PAN

Sets the Auto-Pan operations.

Sets the preset sequence order.

SEQUENCE

TRACE

Stores trace movements.

TRACE 1 PAUSE TIME

Sets the stop duration of trace movements.

ALARM SETTINGS

Sets alarm operations.

INPUT

Sets input number of alarm input.

REPORT

Sets the terminal that transmits the alarm information.

Selects whether to activate the alarm input with make or break contacts.

ACTIVE

Corrects all preset camera positions.

PRESET MEMORY ALL RESET

Resets all preset camera positions.

AUTOMATIC RETURN

HOME

Designates the program the camera automatically returns to.

FREEZE PRESET

AUTO FOCUS

Sets Auto Focus mode.

AGC*

Sets AGC.

SLOW SHUTTER*

Sets slow shutter.

SHUTTER SPEED*

Sets shutter speed.

ELECTRONIC ZOOM

Sets a maximum enlargement of electronic zoom.

ENHANCER*

Sets contour enhancement.

CHROMA*

Adjusts the chroma.

INITIALIZING

Sets whether to forcibly execute action or to set priority order to operation.

PRIORITY*

Sets camera operation when alarm signal is received.

ACTION*

Sets camera operation when the alarm conditions are released.

RESET ACTION*

Sets the period of time that alarm conditions are maintained.

CLOCK

Ver ify alarm logs.

ALARM LOGS

SYNC SYSTEM

Switches sync. system and adjusts phase.

The camera returns to the preset position automatically when the preset period of time elapses by external control.

Displays the still image during camera movement between preset positions.

Sets to give operation priority to black & white mode or slow shutter mode depending on the subject’s brightness.

Return each item on the camera setting screen to the factory default status.

TIMER SETTINGS

Sets the timer.

PROGRAM*

Sets predetermined operations to be performed at preset times.

TIME DISPLAY

Sets time display to 12-hour or 24-hour display formats.

DATE DISPLAY

Sets date display.

TIMER

Sets the time.

DATE

Sets the date.

CONTACT OUTPUT SETTINGS

Sets contact output.

AUX1

Sets contact output.

AUX2*

MANUAL SETTINGS

Individual settings.

ZOOM INTERLOCKING

Resets zoom interlocking.

ROTATION LIMIT

Designate the pan and tilt rotation limits.

ROTATION LIMIT SETTING

Sets the pan and tilt rotation limits.

MANUAL SPEED

Sets the maximum speed of pan and tilt operation.

FLIP*

Sets whether to set the tilt rotation range to 90 or over.

TILT ANGLE LIMIT

Sets the tilt angle limit.

MAINTENANCE SETTINGS

Sets functions during maintenance.

INITIALIZING

Corrects deviation of stepping motor.

Corrects deviation of position.

REFLESH

PASSWORD

Sets the password required when activating maintenance menu screen.

MOTOR POWER

Improves deviation of preset position.

INITIAL STATUS

Returns all setting to initial status set by the factory.

AUTOMATIC CORRECTION

Automatically corrects deviation of position.

DATA BACKUP

Sets data writing and reading.

MOTION DETECTION*3 *

Sets motion detection.

PRIVACY MASKING*

Sets privacy masking area.

*1 Setting for this item can be entered by the Main Menu screen not by the Camera Menu screen

when the equipments other than the C-RM500 are connected. *2 Can also be changed for individual positions at the Camera setting screen for individual positions. *3 Can be only set for the C-CC564 and C-CC764. *4 Can be only set when the C-RM500 is connected. *5 Can be only set for the C-CC564.

Page 8

C-CC764/C-CC714

APPEARANCE AND DIMENSIONAL DIAGRAM

ø179.9

ø150

ø218.5

ø230

330.5

219.5

Multi-pair cable 8 P, loose end

Power cord length Approx. 1.8 m

Cable end: 2 P loose end BNC-R jack

Coaxial cable length Approx. 1.8 m

Multi-pair cable length Approx. 1.8 m

Safety wire length Approx. 20 cm

521

279

140

200

140

16540

33.5

4–ø11.4

100

164

Hook to connect safety wire

188.1

ø48.3

Applicable camera

(option)

Cable entry hole

on a wall ø50

Wall mounting example

Safety wire fixing screw

ø219.8

1338.9

115ø150

164

200

445

165

129

ø48.3

33.5

4–ø11.4

140 100

Hook to connect safety wire

Cable entry hole on a ceiling ø50

Ceiling mounting example

Applicable camera

(option)

Figure as viewed from point A

Wall mounting bracket C-BC711W (option)

Mounting example

Pole

ø90– ø340

Pole mounting bracket YS-60B (option)

Applicable camera

(option)

140 100 ø80

4–ø11

57.6˚

165

200

Unit: mm

C-CC764/C-CC714 C-BC711W

C-A711DM

C-BC711P

C-BC711PM

Page 9

C-CC564/C-CC514

APPEARANCE AND DIMENSIONAL DIAGRAM

Mounting to a heavy-duty ceiling (such as a concrete ceiling)

(View of an optional camera

installation cover attached)

■INSTALLATION EXAMPLE

1. When routing both the coaxial, power cables and signal cable from the speaker side.

Anchor bolt

(female screw)

mounting distance

Note: For anchor bolts, use the unit

driving type female screws (M4).

2. When routing both the coaxial, power cables and signal cable from the ceiling panel.

Camera

center

ø80–ø90

122

122234

ø118 ø168

4–ø4.5

Connector 1

Power supply terminal block

C-BC511C (option) or C-BC511C-S (option)

BNC jack

84 122 132

Safety wire (accessory) (Connect this wire to an object other than the bracket.)

Anchor bolt

C-BC511A

Camera mounting screw

(accessory)

Ceiling board

C-BC511C (option) or C-BC511C-S (option)

Applicable camera

(option)

Note: The mounting hole in the ceiling

is ø144–ø150 mm in diameter.

Ceiling mounting

13x35 (Anchor bolt mounting hole)

4–ø7 (Safety wire mounting hole)

4–ø4.5 (Electric work box mounting hole)

4–M4 (Camera mounting hole)

233

40 81

ø150

ø48.26

46.23

Safety wire (accessory) (Connect this wire to an object other than the bracket.)

“C” channel bracket

Ceiling board

Ceiling hole

Top cover (accessory)

C-BC511C (option) or C-BC511C-S (option)

Applicable camera

(option)

4–ø5 (Ceiling mounting hole)

Drop prevention screw (M5)

4–M4 (Ceiling mountion hole)

Note: When extending a pipe,

use a commercial “88” stainless steel wound pipe or copper sheet wire tube (ø48.3 mm). (In this event, make holes as illustrated.)

Note: The mounting hole in the ceiling is

ø40–ø50 mm in diameter.

Ceiling mounting

203

ø150

46.3

128

122

ø150

203

370.2

292.5

C-BC511W

Wall mounting

C-BC511C (option) or C-BC511C-S (option)

Applicable camera

(option)

128

81 40

4–M4 (Camera mounting hole)

4–ø5 (Wall mounting hole)

ø125 ø168

ø168

C-BC511C

182.2

242.2

Applicable camera

(option)

Mounting

Cable entry hole

4–ø6

228

ø125 ø250

282.7

2–10x20 (Safety wire mounting hole)

Safety wire (accessory) (Connect this wire to an object other than the bracket.)

Anchor bolt

C-BC511U

Ceiling board

Note: The mounting hole

in the ceiling is ø232–ø236 mm in diameter.

Applicable camera

(option)

Ceiling mounting

10x20 (Anchor bolt mounting hole)

Unit: mm

C-CC564/C-CC514 C-BC511A

C-BC511C/C-BC511C-S C-BC511P

C-BC511U/C-BC511U-S C-BC511W

Page 10

C-RM500

REMOTE CONTROLLER

The C-RM500 Remote Controller is designed for use in camerabased systems that allow remote control from up to 1.2km away over RS-485 communication lines. It allows video images to be switched remotely and can handle a maximum of 16 TOA's Combination Dome Cameras when used together with the TOA Multiplexer. Easy-to-see LEDs inform status of control, alarm, focus and other functions.

Control up to 16 TOA's Combination Dome Cameras

Realtime control as well as preprogrammed position retrieval of up to 255 positions is provided. Each position allows providing a specific title as well remote image quality adjustment.

Instant position recall

The most used camera and position numbers can be assigned to function keys A through H for one-touch instant recall. Other camera numbers and position numbers can be assigned to ID numbers from 1 through 512 and easily retrieved using the tenkey pad.

Controls Multiplexer

The C-RM500 can also control the TOA multiplexers and allows switching video image display modes – single screen, single screen in sequence, 4-screens in sequence, as well as 4, 9, 10 and 16-segment split screens.

Alarm capability

Alarm signals received by the alarm input of combination dome cameras can be transmitted to the C-RM500 via a pair of RS-485 communication line where the C-RM500’s alarm operations can be activated, based on the alarm signal type received. This has reduced the number of signal lines that were conventionally required in an expanded system. An Alarm Hold function allows temporarily suspending automatic switching of video images triggered by an alarm to enable the operator to prioritise the screen currently being viewed. In addition, the C-RM500 can receive alarm signals from an C-AL80 unit through the RS-232C port.

2 Location Control

The system can be independently controlled in two separate locations by installing 2 C-RM500 units.

●

Power Source 12 V DC Current Consumption 150 mA Slave Remote Controller RS-485, screwless connector Camera Control RS-485, screwless connector (*

)

Switcher Control RS-485, screwless connector RS-232C, D-sub connector (9 pins, male)

Alarm Input RS-232C, D-sub connector (9 pins, male) Alarm Output/ Alarm output: 16 channels, NPN open collector output,

Control Input withstand voltage: 30 V DC,

control current: 20 mA

Alarm input: 1 channel, no-voltage make contact input,

open voltage: 5 V DC, short-circuit current: 5 mA max.

Home position selection input:

1 channel, no-voltage make contact input, open voltage: 5 V DC, short-circuit current: 5 mA max.

D-sub connector (25-pins, female) Display LED indication of control status, alarm status, alarm hold

status, still picture status, defroster, auxiliary setting, auto, auto focus, and lens speed LCD indication of key entry confirmation

Alarm Signal Continuous alarm tone (can be turned on and off) Number of Unit Up to 2 (one to be set for MASTER unit, another for

Connections SLAVE unit) Maximum Cable 1.2 km (*

) (between the Remote controller and the

Distance Combination cameras) Operating Temperature 0°C to +50°C Operating Humidity Under 90% RH (no due condensation produced) Finish Panel: Surface-treated steel plate, sand gray, paint

Sides: Rubber

Dimensions 326 (W) × 62 (H) × 185.2 (D) mm Weight 1.8 kg Accessory D-sub connector (9 pins, male) × 1,

D-sub connector(25 pins, male) × 1

Applicable Model Combination dome camera: C-CC504S, C-CC554S (option) Switcher: C-MS161D, C-MS91D

Slave remote controller: C-RM500 Interface unit: C-IF500 Alarm unit: C-AL80

(*1) Can connect up to 31 units mixing with combination cameras and interface units. (*

) Applies to the system where the unit and combination camera are connected in a matched pair.

Represents the total of connected cable distances if multiple combination cameras or interface units are connected in the system (when the CPEV-S cable thicker than 0.65 mm in diameter is used)

SPECIFICATIONS

APPEARANCE AND DIMENSIONAL DIAGRAM

Unit: mm

57.9

31.7

185.2

Figure of the installed unit

63.3

10˚

181

326

Page 11

C-IF500

INTERFACE UNIT

C-AL80

ALARM UNIT

SPECIFICATIONS (H/L)SPECIFICATIONS

APPEARANCE AND DIMENSIONAL DIAGRAM

A useful option for configuring camera systems, the C-IF500 functions as a splitter. It provides control over expanding a camera system when the distance is over 1.2km (max. 3km) between the dedicated C-RM500 Remote Controller and system cameras linked to it. It will also allow configuring a star connection. Receiving the RS-485 communication line serial signals, the C-IF500 splits the signals into 4-channel data for slave units and converts into RS-232C data to be used for public line or fiber optics communication. Data communication between master and slave terminals is bidirectional. The C-IF500 also allows easily setting the data communication data transfer rate in four increments via DIP switch to suit network requirements.

Unit: mm

210

279.8

284.1

Power Source 12 V DC Current Consumption 100 mA External Control Master: RS-485, screwless connector

terminating resistance (100 Ω) switch ON/OFF

Slave(*

): 4 channel, RS-485, screwless connector

RS-232C, D-sub connector (9-pin, male) Display Power LED indicator, communication LED indicators

(TX, RX)

Maximum Cable RS-485: 1.2 km (*

)

Distance RS-232C: 10 m Communication Speed 4800 bps, 9600 bps, 19200 bps, 38400 bps Operating Temperature -10°C to +50°C Operating Humidity Under 90% RH (no due condensation produced) Finish Panel: Aluminum, black, 30% gloss, paint

Case: Pre-coated steel plate, 30% gloss, black

Dimensions 210 (W) x 46 (H) x 284.1 (D) mm Weight 1.4 kg Option Rack mounting bracket:

M-15B-BK (for rack mounting one C-IF500 unit)

MB-15B-J (for rack mounting two C-IF500 units)

(*1) Communications cannot be made between slave terminals.

Each slave terminal can connect up to 31 cameras. (except RS-232C port)

) Applies to the system where the unit and combination camera are connected in a matched pair.

Represents the total of connected cable distances if multiple combination cameras or Interface units are connected in the system (when the CPEV-S cable thicker than 0.65 mm in diameter is used).

Power Source H: 230 V AC, 50/60 Hz

L: 120 V AC, 50/60

Power Consumption under 3 W Alarm/Remote Input 32 channels, no-voltage make contact input, open

voltage: 5 V DC, short-circuit current: max. 5 mA, M3 screw terminal, distance between barriers: 7.62 mm

Control Input/Output 1 channel, RS-232C, D-sub connector (9 P, male)

(only valid for master unit), fixed to 38,400 bps

Master/sub Connection 2 channels, RS-485, maximum cable length: 1200m, Terminal DIN connector (5 P)

Alarm Reset Input 1 channel, no-voltage make contact input, open

voltage: 5 V DC, short-circuit current: max. 5 mA, D-sub connector (25 P)

Setting Switches Master/Slave: 3-bit DIP switch

(Selection of Master or Slave 1—7)

Alarm/Remote: 1-bit DIP switch

(Alarm/Remote selection)

Alarm time: 1-bit DIP switch (Edge/Level selection)

RS-485 terminal: Rear-mounted slide switch (RS-485

termination, Enable/Disable selection)

Application Indoor use Operating Temperature 0°C to +50°C Finish Panel: Aluminum extrusion, black, 30% gloss

Case: Pre-coated steel plate, black, 30% gloss

Dimensions 420 (W) × 96.6 (H) × 335.8 (D) mm Weight 3.6 kg Accessory DIN plug × 2, RS-232C cable (2 m) × 1, D-sub

connector (25 P) × 2, Power cord (2 m) × 1

Option Rack mounting bracket: MB-23B Application Model Remote controller: C-RM500

The C-AL80 Alarm Unit serves as the main controller for the alarm requirements of a system by converting alarm signals initiated by externally connected equipment into RS-232C-compatible signal data. In addition to its 32 alarm or remote inputs, the C-AL80 can also be linked to a maximum of 8 other C-AL80 units in master/ slave configurations. This provides a total of 256 alarm or remote inputs to be transmitted to the C-RM500 remote controller.

88.4

96.6

420

335.8

319.8

Front cover

Enlarged figure for

the inside of a front cover

Page 12

Specifications are subject to change without notice. Printed in Japan (0307) 833-53-001-5A U

TOA Corporation

URL : http://www.toa.jp/

SYSTEM EXAMPLES

Monitor

Remote Controller

C-RM500

Combination Dome Cameras C-CC564

1. Combination Dome Camera (1 unit)

C-MS161D

Monitor

Remote Controller

C-RM500

Combination Dome Cameras C-CC564

2. Combination Dome Camera (16 units)

Sensor

max. 8

C-MS161D

Monitor

RS-232C

Remote Controller

C-RM500

Combination Dome Cameras C-CC564

max. 3

max. 256

max. 3

C-AL80

4. Sensor-activated Dome Camera operation.

Multiplexer

Alarm Unit

Multiplexer

max.

CC-3331B

Monitor

Remote Controller

C-RM500

C-IF500

max. 3km

C-IF500

3. When Combination Dome Camera and Remote Controller are separated by more than 1.2km.

Cable Compensator

C-CC514

C-CC764

Combination Dome Cameras C-CC564