TMT Automation BOXER500E, BOXER800E User Manual
FOR RESIDENTIAL
USER MANUAL
24V DC MOTOR
SLIDING GATE OPENERS
BOXER500E / BOXER800E
INSTRUCTIONS BOXER500E / BOXER800E SLIDING GATE OPENER USER MANUAL
1
INDEX
1. WARNINGS
2. INSTALLATION
2.1 STANDARD INSTALLATION DEMONSTARTION
2.2 DESCRIPTION OF DEVICE
2.3 DIMENSION OF DEVICE
2.4 INSTALLATION OF MOTOR GEAR AND GEAR RACK
2.5 CHECKING FOR INSTALLATION
2.6 EMERGENCY RELEASE
3. SETUP AND FUNCTION SETTING
3.1 WIRE CONNECTION
3.2 TRANSMITTER MEMORIZATION AND ERASING PROCESS
3.3 SYSTEM LEARNING, RESET PROCESS AND LED DISPLAY
3.4 PROGRAMMABLE FUNCTION SETTINGS
3.5 TESTING AND CHECKING
3.6 SW2/SW6 SETTING
4. TECHNICAL CHARACTERIESTICS
4.1 TECHNICAL DATA SHEET OF SERIES
4.2 H2 PHOTOCELL DATA SHEET
4.3 R1 TRANSMITTER DATA SHEET
4.4 FL2 FLASHING LIGHT DATA SHEET
5. ADDITIONAL INFORMATION
5.1 WIRE CONNECTION OF H2 PHOTOCELL (SAFETY BEAM)
5.2 GREEN BOX INSTALLATION GUIDE
P. 2
P. 3
P. 3
P. 3
P. 4
P. 4
P. 5
P. 5
P. 6
P. 6
P. 7
P. 7
P. 8
P.10
P.10
P. 11
P. 11
P. 11
P. 11
P. 11
P.12
P.12
P.13
2
INSTRUCTIONS BOXER500E / BOXER800E SLIDING GATE OPENER USER MANUAL
1. GENERAL PRECAUTION:
WARNING :
This user manual is only for qualified technicians who is specialized in installations and automations.
(1) All installations, electrical connections, adjustments and testing must be performed only after reading and
understanding of all instructions carefully.
(2) Before carrying out any installation or maintenance operation, disconnect the electrical power supply by
turning off the magneto thermic switch connected upstream and apply the hazard area notice required by
applicable regulations
(3) Make sure the existing structure is up to standard in terms of strength and stability
(4) When necessary, connect the motorized gate to reliable earth system during electricity connection phase.
(5) Installation requires qualified personnel with mechanical and electrical skills.
(6) Keep the automatic controls (remote, push bottom, key selectors…etc) being placed properly and away
from children.
(7) For replace or repair of the motorized system, only original parts must be applied. Any damage caused by
inadequate parts and methods will not be claimed to motor manufacturer.
(8) Never operate the drive if you have any suspect with what it might be faulty or damage to the system.
(9) The motors are exclusively designed for the gate opening and closing application, any other usage is
deemed inappropriate. The manufacture should not be liable for any damage resulting from the improper
use. Improper usage should void all warranty, and the user accepts sole responsibility for any risks there
by may accrue.
(10) The system may only be operated in proper working order. Always follow the standard procedures by
following the instructions in this installation and operating manual.
(11) Only command the remote when you have a full view of the gate.
TMT AUTOMATION INC. shall not be liable for any injury, damage, or any claim to any person or
property which may result from improper use or installation of this system.
Please keep this installation manual for future reference.
2.1 STANDARD INSATLLATION DEMONSTARATION
1. 24Vdc Sliding motor
2. Transmitter
3. safety photo Sensor
4. Flashing light
2. INSTALLATION:
4
2
1
2.2 DESCRIPTION OF DEVICE
a. Operation gear
b. Limit switch device
c. 24Vdc motor
d. Back-up batteries (Optional)
e. Release device
f. Control panel
g. Terminals of devices
h. Green Box (Optional)
e
h
f
g
a
b
c
d
INSTRUCTIONS BOXER500E / BOXER800E SLIDING GATE OPENER USER MANUAL
3
3
3
Loading...