TMT Automation Boxer 300, Boxer 400, Boxer 500, Boxer 800 User Manual
BOXER SERIES
SLIDING GATE OPENER
USER MANUAL
BOXER SERIES SLIDING GATE OPENER USER MANUAL
1
INDEX
1. GENER SAFETY PRECUATION
2. INSTALLATION
2.1 STANDARD INSTALLATION DEMONSTARTION
2.2 DESCRIPTION OF DEVICE
2.3 DIMENSION OF DEVICE
2.4 INSTALLATION OF GEAR MOTOR AND GEAR RACK
2.5 CHECKING FOR INSTALLATION
2.6 EMERGENCY RELEASE
3. SETUP AND FUNCTION SETTING
3.1 WIRE CONNECTION
3.2 TRANSMITTER MEMORIZATION
3.3 SYSTEM LEARNING AND LED DISPLAY
3.4 PROGRAMMABLE FUNCTION SETTINGS
3.5 TESTING AND CHECKING
3.6 SW2/SW6 SETTING
4. TECHNICAL CHARACTERIESTICS
4.1 TENICAL DATA SHEET OF BOXER SERIES
4.2 H2 PHOTOCELL DATA SHEET
4.3 TM3 TRANSMITTER DATA SHEET
4.4 FL2 FLASHING LIGHT DATA SHEET
4.5 RB1 EXTERNAL RECEIVER BOX DATA SHEET
5. ADDITIONAL INFORMATION
5.1 WIRE CONNECTION OF H2 PHOTOCELL (SAFETY BEAM)
5.2 WIRE CONNECTION AND SETTING OF RB1 EXTERNAL RECIEVER BOX
P. 2
P. 3
P. 3
P. 3
P. 4
P. 4
P. 5
P. 5
P. 6
P. 6
P. 7
P. 7
P. 8
P. 9
P.10
P.10
P.10
P. 11
P. 11
P. 11
P. 11
P.12
P.12
P.13
1. GENERAL PRECAUTION:
BOXER SERIES SLIDING GATE OPENER USER MANUAL
2
WARNING :
This user manual is only for qualified technicians who is specialized in installations and automations.
(1) All installations, electrical connections, adjustments and testing must be performed only after reading and
understanding of all instructions carefully.
(2) Before carrying out any installation or maintenance operation, disconnect the electrical power supply by
turning off the magneto thermic switch connected upstream and apply the hazard area notice required by
applicable regulations
(3) Make sure the existing structure is up to standard in terms of strength and stability
(4) When necessary, connect the motorized gate to reliable earth system during electricity connection phase.
(5) Installation requires qualified personnel with mechanical and electrical skills.
(6) Keep the automatic controls (remote, push bottom, key selectors…etc) being placed properly and away
from children.
(7) For replace or repair of the motorized system, only original parts must be applied. Any damage caused by
inadequate parts and methods will not be claimed to motor manufacturer.
(8) Never operate the drive if you have any suspect with what it might be faulty or damage to the system.
(9) The motors are exclusively designed for the gate opening and closing application, any other usage is
deemed inappropriate. The manufacture should not be liable for any damage resulting from the improper
use. Improper usage should void all warranty, and the user accepts sole responsibility for any risks there
by may accrue.
(10) The system may only be operated in proper working order. Always follow the standard procedures by
following the instructions in this installation and operating manual.
(11) Only command the remote when you have a full view of the gate.
TMT AUTOMATION INC. shall not be liable for any injury, damage, or any claim to any person or
property which may result from improper use or installation of this system.
Please keep this installation manual for future reference.
2.1 STANDARD INSATLLATION DEMONSTARATION
1. 24Vdc Sliding motor
2. Transmitter
3. safety photo Sensor
4. Flashing light
a. Operation gear
b. Limit switch device
c. 24Vdc motor
d. Back-up batteries
e. Release device
f. Control panel
g. Terminals of devices
BOXER SERIES SLIDING GATE OPENER USER MANUAL
3
2. INSTALLATION:
3
4
2
3
e
f
g
a
b
c
d
1
2.2 DESCRIPTION OF DEVICE
Loading...