Page 1
English
VK63
VK67
VK83
*1 : Hour hand O O O
*2 : Minute hand O O O
*3 : Center 1/5 chronograph second hand O O O
*4 : Small second hand O (6H) O (6H) O (6H)
*5 : Chronograph minute hand (60 minute) O (9H) O (12H) X
*6 : 24 hour hand O (3H) X O (3H)
*7 : Chronograph hour hand (12 hour) X O (9H) X
*8 : Chronograph minute hand (20 minute) X X O (9H)
*9 : Button A (START / STOP) O O O
*10 : Button B (RESET) O O O
*11 : Crown at normal position O O O
*12 : Crown at first position (Date setting) O O O
*13 : Crown at second position (Time setting) O O O
Set the time
1) Pull out the crown to the second click position.
2) Turn the crown to set hour and minute hand (Check that AM / PM is set correctly).
3) Push the crown back into the normal position.
* If the crown is pulled to the second position while the chronograph is started, the chronograph hands will continue to
move. This is not a malfunction.
Set the date
1) Pull out the crown to the first click position.
2) Turn the crown clockwise for date setting.
* Do not set the date between 9:00PM and 3:00AM, otherwise the day may not change properly. If it is necessary
to set the date during that time period, first change the time to any time outside it, set the date and then reset
the correct time.
3) Push the crown back into the normal position.
Method 1
1) Set the crown to the normal position
2) Touch the AC terminal of circuit block and the switch spring with conductive
tweezers to reset the circuit.
3) The small second hand will move at two-second interval for 10 seconds as a
demonstration.
Method 2
1) Pull out the crown to the second click position.
2) Press the button B for two seconds and release the button.
3) Push the crown back to the normal position.
4) The small second hand will move at two-second interval for 10 seconds as a demonstration.
* If the crown is operated within the 10 seconds, the two-second interval movement will not be activated.
* It is not necessary to set the chronograph hands after the battery is exchanged. If the chronograph hand positions are
incorrect, following below procedure all the chronograph hands will be reset to "0" position
<< OPERATION -- VK63 / VK67 / VK83 >>
DISPLAY AND CROWN/ BUTTON OPERATION
TIME SETTING
HOW TO RESET (AFTER BATTERY CHANGE)
<< VK63 >> << VK67 >> <<VK83>>
Button A Button A Button B
(START) (STOP) (Reset)
Page 2
English
[ Standard measurement : e.g. 100m race ]
Press the buttons in the following order : A A B
* (6 hour 20 minutes 10 seconds) *
*
VK63 : 60 minutes
* The chronograph can measure up to VK67 : 12 hours and chronograph stops after
VK83 : 20 minutes
VK63 : 60 minutes
a measurement for VK67 : 12 hours
VK83 : 20 minutes
* After the maximum measurement time finished, to restart the chronograph function :
VK63 / VK67 : Press button A
VK83 : Press button B (to reset the chronograph minute hand to "0" position) then press button A
* During the chronograph operation, button B (reset) can be pushed. It will not cause any problem.
[ Accumulated elapsed time measurement : e.g. basketball game ]
Press the buttons in the following order :
A A / A … A B
* Restart and stop of the chronograph can be repeated as many times as necessary by pressing button A.
SII Products
HOW TO USE THE CHRONOGRAPH
START STOP (Finish) RESET
(1 hour 8 minute 40
seconds)
(6 hour 20 minute 10
seconds)
Press button A to start the
chronograph. The
chronograph hands wil start
moving.
Press button A again to stop
the chronograph. The
chronograph hands stop to
indicate the elapsed time.
Press button B to reset the
chronograph. All the
chronograph hands will be
reset to "0" position
START STOP / RESTART STOP RESET
A
A
B
A A
A
B
Loading...