Tmi 008-00018 Installation Manual
GETTING STARTED
Open all carton(s) containing hardware and remove all items. Position the hardware
on the floor under the opening. Next, look in the box containing the curtain. The
height and width of the curtain will be listed on a tag attached to the curtain.
NOTE: The actual height will be 3'' shorter to allow for the thickness of the sliding
track and a 1'' gap off the floor. Please check the chart below to make sure you
have the correct number of items.
Curtain Width
72'' 144'' 288''
Item Model No. No. Req’d No. Req’d No. Req’d
Straight Track 008-00180 1@48'' 3@ 48'' 6@48''
1@ 24''
Universal Mounting Bracket 095-00001 2 4 8
Ceiling Support Connector 008-00018 2 4 8
Straight Splice Connector 008-00082 1 2 5
Nylon Roller with Hook 008-00064 8 14 28
End Stop 008-00028 2 2 2
Curtain 1 1 1
NYLON ROLLER
WITH HOOK
STRAIGHT SPLICE
CONNECTOR
END STOP
STRAIGHT TRACK
008-00180
UNIVERSAL BRACKET
095-00001
INDUSTRIAL CURTAIN
008-00082
008-00064
008-00028
008-00018
CEILING SUPPORT CONNECTOR
INDUSTRIAL CURTAINS
INSTALLATION INSTRUCTIONS
Step 5
Step 4
ATTACHING TRACK TO BRACKET/SUPPORT CONNECTOR
Step 6
HANGING THE CURTAIN
NOTES
INSERTING NYLON ROLLERS WITH HOOKS
Place each curtain grommet over a
roller hook and mounting is complete.
The logo should face to the outside.
1) Place each roller into the open end
of the track. The number of rollers
must be equal to the number of grommets
on the top edge of the curtain.
For this step you will need an assistant.
1
2
2) Affix the second End Stop
to the open end of the track.
First, remove the
Track Holder Plate
from each of the
Support Connectors
Next, place the Straight
Track (assembly) into the
Support Connector.
Finally, replace the track
holder plate to each of the
Support Connectors and
tighten the locking nut so
the track is secure.
Track
Holder
Plate
Straight
Track
(Assembly if
multiple
tracks)
Catalog Number IC-II-06-07
Copyright 2007 TMI, LLC
Step 1
If you are ceiling mounting, use the Ceiling Support Connectors only.
Step 2
Important Note for All Mounting Methods
Place the Ceiling Support Connector
on the ceiling. Mark the 2 mounting
holes. Remove the bracket, drill the 2
holes and screw the bracket to the
ceiling.
Place each Mounting Bracket on the
wall so the top edge of the bracket is even
with the line. Mark the 2 mounting holes. Remove the bracket,
drill the 2 holes and screw the bracket to the wall.
Using this method, you will need beam clamps
and threaded rods that are not included with
your hardware. 1. Measure the distance from
bottom of the roof beam or truss. Subtract from
that amount, the height of the curtain plus an
additional 3''. The threaded rods should be
2'' longer than that final measurement.
NOTE: It is important that all of the threaded
rod ends are level with one another.
SUSPENDED
MOUNT
Threaded
Rods
Ceiling
Support
Connector
CEILING
MOUNT
Determine which method of mounting will be used
. . . CEILING, WALL or SUSPENDED.
The Universal Mounting Brackets (with the
Ceiling Support Connector attached) can
be used for either wall mounting or
connects to a suspending threaded rod
(
3
/ 8'' Threaded Rod supplied by others).
IMPORTANT: While installing the hardware add
3'' to the height stated on the curtain tag.
WALL
MOUNT
Universal
Mounting
Bracket
1
1. On the bulkhead, place a mark 5'' higher than
the height of your curtain on one side.
2. From that point stretch a line level to the
opposite side and place a mark. That distance
should be the length of your Straight
Track assembly. See Step 2.
3. Connect the marks with a straight
level line.
Whether you are mounting a single piece of track or multiple pieces
that you have spliced together, you should place the Mounting
Brackets approximately 6'' from each end and each side of a Splice
Connector.
BEAM CLAMP
Place a nut 1'' up from the bottom of the threaded rod. Next
place a washer over the rod, then the Universal Mounting Bracket,
and finally another washer and nut. Tighten the assembly.
See the illustration to the right.
Loosely place 2 allen screws onto each
Straight Splice Connector, just one and
a half turns
1. Insert the two tracks and tighten the screws.
Repeat this process until all pieces of track are
spliced together.
1
6''
6''
6''
2
1
1
1
2
2
2
3
2. Affix an End Stop
to just one open end.
3. Measure the
length of the
track
1) Affix an End Stop to just one open end.
SPLICING MULTIPLE TRACKS TOGETHER
SINGLE TRACK
Step 3 – CEILING MOUNTING
Step 3 – WALL MOUNTING
Step 3 – SUSPEND MOUNTING
However, it is more important to attach the bracket to
solid material than to comply with the 6'' measurement.
1. This height is pre-determined by your ceiling height.
IMPORTANT: Make sure the ceiling height is at least
3'' higher than your curtain height.
2. Place a mark on the ceiling where both ends of the
track will fall. See Step 2 for track length measurement.
3. Connect these marks with a straight line.
The ceiling surface must be flat and level with the floor.
3
Loading...