TLS Prime Operator's Manual

Preset Torque Screwdrivers
Prime, Pro & ESD
DrehmomentbegrenzendeSchraubendreher,
Tournevisdynamométriquea Pre-Reglage,
AtornilladoresCon LimitadorDe Par –GrifivitiLimitadoriDi Coppia
Operators Manual
Instruction Part Number P34980 Issue 2
Torque Limiting Screwdriver –Prime, Pro & ESD
Products:Prime, Pro & ESD Mechanism Type:Slipping ISO 6789 Designation: Type 2, Class F (Pro & ESD only)
Repeatability:+/-6% of Torque Setting (Pro & ESD)
+/-10% of Torque Setting (Prime)
Calibration Period:Every 12 Months or 5000 cycles (minimum)
(Pro & ESD only)
Safety & Maintenance
•Use only as a Torque Screwdriver.
•Do not use as a hammer, chisel or pry bar.
•Only hold the tool using the hand grip.
•For increased leverage, use the T-Bar provided (Large Pro & ESD Only)
•For ease of identification use different colour cap ends (Pack of four, Order Code:065800)
•Always ensure that the screwdriver is in correct alignment withthe fastener
•Torque tools should be regularly calibrated and inspected to ensure correct operation
•Ensure the tool is clean and free of oil, grease and water before use
•Never dip into cleaning fluid or petroleum
Spare parts, servicing and calibration instructions are available from Torqueleader. Please contact us or visit www.torqueleader.com for further information.
Sales Hotline +44 (0) 1483 894476
TLS Screwdrivers –Prime, Pro & ESD
Adjustment Procedure 1
Check Setting
Using a Torque Analyser, check the setting of the screwdriver.
2
3
Prime
Pro
If adjustment is necessary
Use a 5mm hexagon key to remove the end cap fitted to Pro & ESD models only. Also remove the T-Bar where fitted. Then insert the hexagon key into the end of the hand grip to engage the adjusting screw.
Increase Torque
Rotate the key clockwise until the correct torque is shown consistently on the analyser. (10 readings).
Reduce Torque
When adjusting, always approach the required torque from a lower setting.
To reduce the torque, rotate the key anti­clockwise past your setting, then increase torque to the required value.
TLS Screwdrivers are designed for use with sockets, screwdriver bits and blades.
At the set torque, the handle rotates through an angle of 60Obefore resetting.
www.torqueleader.com
Torqueleader –TAKING THE RISK OUT OF TIGHTENING
Measure
•Torque measuring tools are used in Research, Development, Inspection and Quality Control where there is a need to check torque settings. This type of tool can also be used in a servicing or Production environment to apply torque.
•Measuring Torque Tools feature a dial or digital readout and are available in screwdriver or wrench formats, covering torque values up to 2000 N.m.
Apply
•Torque applying tools are used to apply a set torque to a fastener. The tool will Click, Break or Slip to signal to the operator when the set torque has been achieved.
Preset tools are ideal for production areas where the same torque is applied repeatedly.
Calibrated Scaletools are operator adjustable and are ideal for servicing applications where ease of adjustment is essential.
Torqueleader offer two types of Torque Analyser:
Mechanical Analysers offer a low cost robust and easy to use device, designed to set and calibrate low range torque tools.
Digital Analysers allow the user to download test results, test powered torque tools and reach higher torque values than are possible using mechanical analysers.
LaboratoryCalibrate
•Regular calibration to International Standards is vital to ensure that your torque equipment is operating at its peak performance.
•We have a UKAS Calibration Laboratory, accredited to ISO/IEC 17025:2005 on site, capable of recalibrating most Hand Torque Tools, Analysers and Transducers in accordance with the International Standards.
Loading...