TLS 875700 MF100 User Manual

875700 MF 100 User Manual

875700 MF 100 User Manual

Thank you for purchasing this product. For optimum performance and
safety, please read these instructions carefully before connecting,
operating or adjusting this product. Please keep this manual for future
reference.

SURGE PROTECTION DEVICE RECOMMENDED

This product contains sensitive electrical components that may be
damaged by electrical spikes, surges, electric shock, lightning strikes, etc.
Use of surge protection systems is highly recommended in order to
protect and extend the life of your equipment.

SAFTY AND NOTICE

1) The transmission distances of HDMI over UTP cables are measured
using TE CONNECTIVITY 1427071-6

2) EIA/TIA-568-B termination for CAT cables is recommended for better

performance.

3) DO NOT use 568A/568B standard mixed CAT cable (cross-over cable)
because there are 2 pairs swapped, this will make POH
OVER-CURRENT and damage POH components. Please use
straight-through CAT cable (both RJ45 headers are 568A or 568B
standard).

4) It is recommended that power up the device after connections of
source, sink and CAT cable.

5) To reduce the interference among the unshielded twisted pairs of
wires in CAT cable, do not run HDBaseT / Zone Cat5e/6/6a cabling
with or in close parallel proximity to mains power cables. Shielded
CAT cables can be used to improve EMI problems, which is worsen in
long transmission.

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 2

875700 MF 100 User Manual

6) Because the quality of the CAT cables has the major effect on how
long the transmission limit can achieve and how good is the received

picture quality, the actual transmission range is subject to one’s

choice of CAT cables.

7) Do not substitute or use any other Power Supply other than the
enclosed unit, or a TLS approved Replacement Part. Doing so will
void the warranty and potentially expose the user to dangerous
voltages resulting in an electrical shock.

8) Do not disassemble the device for any reason. Doing so will void the

manufacturer’s warranty. Also, our unique case is an integral part of

the design of this unit and is responsible for cooling and circuitry
shielding. Any modifications to this case will potentially cause
malfunction and product failure.

9) Do not expose the device to water, moisture, or liquids. Possible
electric shock may result as well as failure of the unit to operate.

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 3

875700 MF 100 User Manual

Table of Content

SAFTY AND NOTICE .............................................................................. 2

Introduction .............................................................................................. 5

What is smart CSC?............................................................................. 5

Features .................................................................................................. 6

Panel Descriptions .................................................................................. 7

Transmitter ........................................................................................... 7

Front ..................................................................................................... 7

Back ..................................................................................................... 8

Receiver ............................................................................................... 9

Front ..................................................................................................... 9

Back ................................................................................................... 10

RS-232 switching codes for VGA and HDMI inputs .............................. 11

RS-232 Pin Assignment ..................................................................... 11

RS-232 configuration ......................................................................... 12

Specifications ........................................................................................ 13

Package Contents ................................................................................. 14

Maintenance .......................................................................................... 14

Warranty Policy .................................................................................. 14

Limitations of Warranty ...................................................................... 15

Exclusive Remedies ........................................................................... 15

RMA Policy ......................................................................................... 16

Standard Replacement ...................................................................... 16

Once you have obtained an RMA number ......................................... 16

Application Diagram .............................................................................. 18

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 4

875700 MF 100 User Manual

Introduction

TLS 875700 MF100 Set (Transmitter & Receiver) is an industry leading
4K HDBaseT extender with switchable HDMI and VGA/Audio input. The
extender set uses smart CSC (Color Space Conversion) technology with
no latency, and supports 4K/60Hz with 4:4:4 chroma sampling, as well as
HDMI data rates up to 18 Gbps. It can deliver HDMI/VGA singnal up to
330ft (100m) for 1080p video, and up to 230ft (70m) for 4K HDR over
CAT5e/6a/7 cable. And also transmits bi-directional IR, RS-232 and PoH
up to lengths of 100m over s single CAT cable.

The MF100 Set is ideal for residential applications with the latest
emerging 4K/UHD and HDR sources and displays. It is compatible with
all video resolutions, audio formats, and color space formats supported in
the HDMI 2.0a specification, plus the ability to pass metadata for HDR
content.

Note:

What is smart CSC?

Smart CSC is a technology that can convert 6G video to 3G at TX unit
and recover 3G to 6G at RX unit, and the RX unit can smartly output 6G
or 3G video depends on the sink device capacity.

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 5

875700 MF 100 User Manual

Features

 Switching between HDMI and VGA with 3.5mm audio input, HDMI

output with L/R Analog audio and Coax Digital audio outputs

 HDMI 2.0a
 4K@60Hz with 4:4:4 chroma sampling, plus HDR and full 3D formats
 HDCP-2.2/HDCP 1.x and DVI compliant
 Smart CSC technology supports outputting 6G or 3G video depends

on sink device

 1080p up to 100m/330ft, 4K up to 70m/230ft.
 Support all popular VGA resolution inputs:

640x480@60/75Hz, 720x400@70Hz, 800x600@60/75Hz,
1024x768@60/75Hz, 1152x864@75Hz, 1280x720@60Hz,
1280x768@60/75Hz, 1280x800@60/75Hz, 1280x960@60Hz,
1280x1024@60/75Hz, 1360x768@60Hz, 1366x768@60Hz,
1400x1050@60Hz, 1440x900@60Hz, 1600x1200@60Hz,
1680x1050@60Hz, 1920x1080@60Hz, 1920x1200@60Hz

 Visually lossless compression
 Supports bi-directional POH, only one power supply is needed at TX

or RX side.

 Bi-directional IR and RS232 pass through
 Digital and analog audio breakouts at RX side.
 All PCM, Dolby and DTS multichannel audio formats pass through
 With ESD protection

Note:

The POH function is designed for powering compatible transmitter or
receiver units of TLS only.

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 6

875700 MF 100 User Manual

Panel Descriptions

Transmitter

Front

VGA IN – Connect to VGA source device
Audio IN – 3.5 mm Stereo Jack, Analog audio input (goes with VGA

input)
HDMI Link – HDMI Input LED indicator

LED off – No HDMI input
LED on – HDMI input stable (Lit blue light)

HDMI IN – Connect to HDMI source device
IR RX/TX port – 3,5 mm stereo-phone, connect to IR transmitter

/receiver cable

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 7

875700 MF 100 User Manual

Back

MODE DIP Switch – 2 pin (Up=0, DOWN=1)

00: RS232 pass through
01: Valens firmware upgrade
10: MCU firmware upgrade
11: Switch between VGA & HDMI by codes & RS232 pass through

HDBaseT (Default)

RS 232 port – DB9 female connector, connect to DTE or DCE
Input Select button – Input select button, switch between HDMI and

VGA/Audio input

Inputs indicator light – Red for VGA input, yellow for HDMI input
HDBT Out --- RJ45 connector, connect to HDBT In port on the

receiver side via cat5e/6a/7
Link – HDBT Link LED indicator

LED off – No link
LED blinking – linking or unstable
LED on – Link is stable (Lit yellow light)

DC Power Input --- Screw locking connector, use the included
12V/2A DC adaptor to power the unit

Power LED indicator – Lit yellow when getting power

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 8

875700 MF 100 User Manual

Receiver

Front

MODE DIP Switch – 2 pin (Up=0, DOWN=1)

00: RS232 pass through
01: Valens firmware upgrade
10: MCU firmware upgrade
11: Switch between VGA & HDMI by codes & RS232 pass through

HDBaseT (Default)

RS 232 port – DB9 female connector, connect to DTE or DCE
Input Select button – Input select button, switch between HDMI and

VGA/Audio input,

Inputs indicator light – Red for VGA input, yellow for HDMI input
HDBT IN --- RJ45 connector, connect to HDBT Out port on the

transmitter side via cat5e/6a/7
Link – HDBT Link LED indicator

LED off – No link
LED blinking – linking or unstable
LED on – Link is stable (Lit yellow light)

DC Power Input --- Screw locking connector, use the included
12V/2A DC adaptor to power the unit

Power LED indicator – Lit yellow when getting power

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 9

875700 MF 100 User Manual

Back

Coaxial Audio Out – RCA connector, multichannel digital audio output
Left Audio Out – RCA Connector, button/LED – Input select button,

switch between HDMI and VGA/Audio input, indicator LED – Red for
VGA, Blue for HDMI

HDMI Link – Yellow for connection to HDMI sink
HDMI OUT – Connect to HDMI sink device
IR RX/TX port – 3,5 mm stereo-phone, connect to IR transmitter

/receiver cable

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 10

875700 MF 100 User Manual

No.

Codes

Description

1

HELP

Print Help Information

2

STATUS

Print Help Information

3

MCUT

System UART Test

4

VGASELECT

Switching to VGA input

5

HDMISELECT

Switching to HDMI input

6

GETSELECT

Get status of currently selected input, return message will be HDMI
port or VGA port

7

ENSIGDET

Enable signal detect and Auto switch Input

8

DISSIGDET

Disable Signal detect and Manual switch input

9

PASSON

UART Passthrough is ON

10

PASSOFF

UART Passthrough is OFF

11

PRIOVGA

Set VGA input high priority when auto switch

12

PRIOHDMI

Set HDMI input high priority when auto switch

13

PRIOOFF

Auto switch to last signal preset switch

14

PRIOGET

Get priority setting

15

RESET

Reset system to default settings,
“YES” to confirm, “NO” to discard

MF100

Remote Control Console

PIN

Assignment

PIN

Assignment

1

NC

1

NC

2

Tx

2

Rx

3

Rx

3

Tx

4

NC

4

NC

5

GND

5

GND

6

NC

6

NC

7

NC

7

NC

8

NC

8

NC

9

NC

9

NC

RS-232 switching codes for VGA and
HDMI inputs

Note: Codes are case sensitive. Carriage return ( 0X0D) needs to be

pressed to activate the code.

RS-232 Pin Assignment

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 11

RS-232 configuration

Baud Rate: 57600 bps
Data Bit: 8-bit
Parity: None
Stop Bit: 1-bit
Flow Control: None

875700 MF 100 User Manual

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 12

875700 MF 100 User Manual

Signal

Bandwidth

10.2 Gbps

CEC

Supports CEC pass through

HDCP

2.2 and 1.x backward compatible

Video

HD/SD

4096×2160@24/25/30/50/60Hz,
3840×2160@24/25/30/50/60Hz, 2048x1080p,
1080p@23.98/24/25/29.97/30/50/59.94/60Hz,
1080i@50/59.94/60Hz, 720p@50/59.94/60Hz, 576p, 576i,
480p, 480i

VESA

2560x2048, 2560x1600, 2048x1536, 1920x1200,
1680x1050, 1600x1200,
1600x900, 1440x900, 1400x1050, 1366x768, 1360x768,
1280x1024, 1280x800, 1280x768, 1152x768, 1024x768,
800x600, 640x480

Chroma
Subsampling

4:4:4, 4:2:2, 4:2:0
Color Space

YUV, RGB

Color depth

8-bit, 10-bit, 12-bit

Audio

Bit Rate

24-bit (Maximum)

Sample Rate

32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz,
192 kHz

Formats

PCM 2Ch, LPCM 5.1, LPCM 7.1, Dolby® Digital, DTS 5.1,
Dolby Digital Plus, Dolby TrueHD, DTS-HD, Master
Audio™, Dolby Atmos®, DTS:X

Resolution / Distance

HDMI

4K - 15ft/5m; 1080P – 30ft/10m

CAT5e/6

4K -115ft/35m; 1080P – 200ft/60m

CAT6a/7

4K -130ft/40m; 1080P – 230ft/70m

Temperature

Operating

32°F to 104°F (0°C to 40°C)

Storage

-4°F to 140°F (-20°C to 60°C)

Humidity (RH)

20% to 90%, non-condensing

Power

Supply

Input: 100-240V AC, 50/60Hz, Output: 12V 2A DC

Dimensions & Weight

Dimensions

MF100 Transmitter: 125x118x41mm
MF100 Receiver: 125x118x41mm

Weight

MF 100 Transmitter 420g
MF100 Receiver 430g

Specifications

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 13

875700 MF 100 User Manual

Package Contents

1. 875700 MF100 Set, Transmitter & Receiver

2. 1x 12V DC power supply

3. 1x IR Transmitter, 1x IR Receiver

4. 1x 875700 User Manual

Maintenance

Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner or
benzene to clean this unit.

Warranty Policy

TLS products are warranted against defects in material and workmanship
for two years from the date of shipment. During the warranty period, TLS
will, at its option, repair or replace products that prove to be defective.
Repairs are warranted for the remainder of the original warranty or a 90
day extended warranty, whichever is longer.
For equipment under warranty, the owner is responsible for freight to TLS
and all related customs, taxes, tariffs, insurance, etc. TLS is responsible
for the freight charges only for return of the equipment from the factory to
the owner. TLS will return the equipment by the same method (i.e., Air,
Express, Surface) as the equipment was sent to TLS.
All equipment returned for warranty repair must have a valid RMA
number issued prior to return and be marked clearly on the return
packaging. TLS strongly recommends all equipment be returned in its
original packaging.

TLS’s obligations under this warranty are limited to repair or replacement

of failed parts, and the return shipment to the buyer of the repaired or
replaced parts.

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 14

875700 MF 100 User Manual

Limitations of Warranty

The warranty does not apply to any part of a product that has been
installed, altered, repaired, or misused in any way that, in the opinion of
TLS, would affect the reliability or detracts from the performance of any
part of the product, or is damaged as the result of use in a way or with
equipment that had not been previously approved by TLS.
The warranty does not apply to any product or parts thereof where the
serial number or the serial number of any of its parts has been altered,
defaced, or removed.
The warranty does not cover damage or loss incurred in transportation of
the product.
The warranty does not cover replacement or repair necessitated by loss
or damage from any cause beyond the control of TLS, such as lightning
or other natural and weather related events or wartime environments.
The warranty does not cover any labor involved in the removal and or
reinstallation of warranted equipment or parts on site, or any labor
required to diagnose the necessity for repair or replacement.
The warranty excludes any responsibility by TLS for incidental or
consequential damages arising from the use of the equipment or
products, or for any inability to use them either separate from or in
combination with any other equipment or products.
A fixed charge established for each product will be imposed for all
equipment returned for warranty repair where TLS cannot identify the
cause of the reported failure.

Exclusive Remedies

TLS’s warranty, as stated is in lieu of all other warranties, expressed,
implied, or statutory, including those of merchantability and fitness for a
particular purpose. The buyer shall pass on to any purchaser, lessee, or
other user of TLS’s products, the aforementioned warranty, and shall
indemnify and hold harmless TLS from any claims or liability of such
purchaser, lessee, or user based upon allegations that the buyer, its
agents, or employees have made additional warranties or
representations as to product preference or use.

The remedies provided herein are the buyer’s sole and exclusive

remedies. TLS shall not be liable for any direct, indirect, special,
incidental, or consequential damages, whether based on contract, tort, or
any other legal theory.

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 15

875700 MF 100 User Manual

RMA Policy

When returning product to TLS for any reason, the customer should fill
out the official RMA form to obtain a RMA number. Without the
permission or approval, TLS will be no responsible for any return.This
can be initiated by emailing or calling your related sales.
All requests are processed within 48 hours.

Standard Replacement

For customers that agree to return defective product to TLS first, a
Standard Replacement option is available.
An RMA number must first be issued by sales. This RMA number will
need to be referenced on the outside of the return shipment.
Upon receipt of the defective product, TLS will, at its discretion, either
repair or replace the product and ship it out in the most expeditious
manner possible. Subject to availability, the replacement product will be
shipped on the business day following receipt of the defective product.
In the event the product returned to TLS has been discontinued (i.e. the
product is no longer being manufactured by TLS but is still under
warranty), TLS will, at its discretion, either repair or replace with
recertified product.

Once you have obtained an RMA number
After obtaining an RMA number from TLS, you must send the product -

freight prepaid - to TLS Technology Co., Ltd. The TLS RMA number must
be prominently displayed on the outside of your package. If you send
your product to TLS without the RMA number prominently displayed on
the outside of the package, it will be returned to you unopened.
Please use a shipping company that can demonstrate proof of delivery.
TLS does not accept responsibility for any lost shipments unless proof of

delivery to TLS is provided.

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 16

875700 MF 100 User Manual

Please note:

Product shipped to TLS must be properly packaged to prevent loss or
damage in transit.
Shipping your RMA to TLS using regular mailing envelopes is not
acceptable, as they do not protect the product from damage during
shipping.
TLS will not repair or replace a module that is shipped in such a way that
the product is not properly protected.
TLS will not accept any product that has been damaged as a result of
accident, abuse, misuse, natural or personal disaster, or any
unauthorized disassemble, repair or modification.

Ecco Cine Supply and Service GmbH
Marie-Curie-Str. 20
40721 Hilden
Germany
[phone]

[e-mail]

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 17

Application Diagram

875700 MF 100 User Manual

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 18

875700 MF 100 User Manual

Projektor

Kabel DVI/HDMI

Kabel Audio

Legende:

Kabel VGA

Kabel Steuerleitung

Aktiv-

Lautsprecher

CAT6 (bis zu 100m Kabellänge)

HDMI IN IR Rx IR TxAudioVGA IN

HDMI

Link

HDMI OUT IR Rx IR TxAudio OUT

HDMI

Link

LCoaxial R

HDBaseT OUT

Link

RS232 DC 12VInput

Select

Power

HDBaseT IN

Link

RS232 DC 12VInput

Select

Power

Lautsprecher

IR RX

IR TX

RS232

HDMI / DVI

VGA

Audio

HDMI / DVI

RS232

IR RX

IR TX

Audio

digital

Audio analog

Steuerung

QuickControl XL

TLS electronics GmbH – www.tls-electronics.de contact : [e-mail] 19