TLS 875240 User Manual

875240 HDBaseT / HDMI Splitter 1x4

User Manual

875240 HDBaseT /HDMI Splitter 1x4

TLS electronics GmbH Contact: [e-mail] 2

Thank you for purchasing this product. For optimum performance and
safety, please read these instructions carefully before connecting,
operating or adjusting this product. Please keep this manual for future
reference.

SURGE PROTECTION DEVICE RECOMMENDED

This product contains sensitive electrical components that may be
damaged by electrical spikes, surges, electric shock, lightning strikes,
etc. Use of surge protection systems is highly recommended in order to
protect and extend the life of your equipment.

SAFETY AND NOTICE

1. The transmission distances of HDMI over UTP cables are measured
using TE CONNECTIVITY 1427071-6

2. EIA/TIA-568-B termination (T568B) for CAT cables (AWG 24/1) is
recommended for better performance.

3. DO NOT use 568A/568B standard mixed CAT cable (cross-over
cable) because there are 2 pairs swapped, this will make POE
OVER-CURRENT and damage POE components. Please use
straight-through CAT cable (both RJ45 headers are 568A or 568B
standard).

4. It is recommended that power up the device after connections of
source, sink and CAT cable.

5. To reduce the interference among the unshielded twisted pairs of
wires in CAT cable, do not run HDBaseT / Zone Cat5e/6/6a cabling
with or in close parallel proximity to mains power cables. Shielded
CAT cables can be used to improve EMI problems, which is worsen
in long transmission.

6. Because the quality of the CAT cables has the major effect on how
long the transmission limit can achieve and how good is the received
picture quality, the actual transmission range is subject to one’s
choice of CAT cables.

7. Do not substitute or use any other Power Supply other than the
enclosed unit, or a TLS approved Replacement Part. Doing so
will void the warranty and potentially expose the user to
dangerous voltages resulting in an electrical shock.

8. Do not disassemble the device for any reason. Doing so will void the
manufacturer’s warranty. Also, our unique case is an integral part of

875240 HDBaseT / HDMI Splitter 1x4

TLS electronics GmbH Contact: [e-mail] 3

the design of this unit and is responsible for cooling and circuitry
shielding. Any modifications to this case will potentially cause
malfunction and product failure.

9. Do not expose the device to water, moisture, or liquids. Possible

electric shock may result the unit to operate.

Table of Contents

1. Introduction........................................................................................4

2. Features.............................................................................................4

3. Panel Descriptions............................................................................5

4. DIP Switcher EDID Setting................................................................6

5. Application Diagram..........................................................................7

6. Specifications.....................................................................................8

7. Package Contents............................................................................8

8. Maintenance......................................................................................9

9. Warranty Policy.................................................................................9

10. Limitations of Warranty.....................................................................9

11. Exclusive Remedies........................................................................10

12. RMA Policy......................................................................................10

875240 HDBaseT /HDMI Splitter 1x4

TLS electronics GmbH Contact: [e-mail] 4

Introduction:

The 875240 HDBaseT / HDMI Splitter is a HDBaseT Distribution
Amplifier and splits a single HDMI or DVI audio/video source to 4
HDBaseT outputs and 1 HDMI local output. The HDMI output can be
used to monitor local displays or cascade up to 6 times with additional
875240 HDBaseT / HDMI Splitter. It supports 1080p Full HD up to
4K@30Hz UHD plus all 3D formats, along with multichannel digital audio
formats such as Dolby® True HD and DTS-HD® Master Audio™.
Embedded audio extractors can extract the audio and output via L/R and
Coaxial. Based on HDBaseT Lite chipset inside, the output distance can
reach up to 70m via Cat5e/6/7 (AWG24/1).

TLS HDBaseT PoH Receiver is recommended to utilize the full function
of the HDBaseT outputs of this device. (Not included)

Features:

• Supports resolutions up to 1080p@60Hz, 4K@30Hz, 36-bit deep

color

• Full 3D pass- through.

• Splits a HDMI source to 4 HDBaseT outputs and 1 HDMI output

without loss

• Supports cascading via HDMI OUT, up to 6 times

• HDBaseT Lite chipset inside for the output distance up to 70m for

1080P, 40m for 4K.

• Power the remote receivers, with PoH (Power over HDBaseT), no

power supply needed for the receivers (only TLS receivers!).

• Extract the audio from HDMI source via analog and digital outputs.

• Dolby TrueHD and DTS-HD master audio pass through HDMI output

• Advanced EDID management for rapid integration of sources and

displays

• LEDs for power-on and outputs indication.

• Bi-directional IR supported.

• Easy installation with rack-mounting ears

• Small compact size

• HDCP compliant