TL Electronic SlimLine PT 1082 Series, SlimLine PT 15-1082 Series, SlimLine PT 17-1082 Series, SlimLine PT 19-1082 Series Service Manual

ÐÐ2DQUHBD Manual for

IndustrialÐ/@MDK PC

2lHLLine /3Ðxxa

,QWHOUG*HQ&RUH¥LLL&38
µµµ+LJK3HUIRUPDQFH
)DQOHVV3DQHO3&
:LWK9*$',2/$1

TL Electronic GmbH

Bgm.-Gradl-Str. 1

85232 Bergkirchen-Feldgeding

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

www.tl-electronic.de

Germany

M1

!

Intel® Core™ 3rd Gen. Mobile

i3/i5/i7 High Performance

15”/17”/19” Fanless Embedded PC

COPYRIGHT NOTICE & TRADEMARK

All trademarks and registered trademarks mentioned herein are the property of their
respective owners.

This manual is copyrighted in Sep. 2013. You may not reproduce or transmit in any
form or by any means, electronic, or mechanical, including photocopying and
recording.

DISCLAIMER

This user’s manual is meant to assist you in installing and setting up the system. The
information contained in this document is subject to change without any notice.

CE NOTICE

This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

!

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.

You are cautioned that any change or modifications to the equipment not expressly
approve by the party responsible for compliance could void your authority to operate
such equipment.

CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.

WARNING! Some internal parts of the system may have high electrical voltage. And therefore
we strongly recommend that qualified engineers can open and disassemble the system. The
LCD and touch screen are easily breakable, please handle them with extra care.

!

Contents

TABLE OF CONTENTS

CHAPTER 1 INTRODUCTION

1-1 About This Manual.................................................................... 1-2

1-2 System Illustration...................................................................... 1-3

1-3 System Specifications................................................................. 1-9

1-4 Safety Precautions...................................................................... 1-11

CHAPTER 2 SYSTEM CONFIGURATION

2-1 Jumper & Connector Quick Reference Table............................. 2-2

2-2 Component Locations................................................................ 2-3

2-3 How to Set Jumpers................................................................... 2-5

2-4 Clear CMOS Data Selection…………………………………... 2-7

2-5 CFast Voltage Selection............................................................. 2-7

2-6 COMPorts & Connectors….......................……..……………... 2-8

2-7 COM Ports RI & Voltage Selection…..........…..…………....... 2-9

2-8 COM2 RS232/422/485 Selection............................................... 2-10

2-9 COM2 Auto Detect Selection.................................................... 2-11

2-10 DIO Connector…….............……………………...................... 2-11

2-11 Flash Descriptor Override Selection…………………………... 2-12
2-12 Front Panel Connector & Selection…………………………… 2-13

2-13 Internal Keyboard & Mouse Connectors.................................... 2-14

2-14 Hardware Power Failure Selection.…………………………… 2-14
2-15 JUSB Port Connector………………………………………….. 2-15
2-16 LAN Connector………………………………………………... 2-15
2-17 Printer Port…………………………………………………….. 2-16

2-18 LVDS Connector……………………………………................ 2-17

2-19 LVDS Inverter Connector……………………………………... 2-17
2-20 LVDS Panel Brightness Control Selection……………………. 2-18
2-21 LVDS Voltage Selection………………………………………. 2-18
2-22 Power Input Connector………………………………………... 2-19
2-23 SATA & SATA Power Connectors…………………………… 2-20

!

Contents

2-24 Audio Connector………………………………………………. 2-21

2-25 System Fan Connector ………………………………............ 2-22

2-26 USB 3.0 Connector……………………………………………. 2-22
2-27 VGA Connector……………………………………………….. 2-23
2-28 SIM Card Slot…………………………………………………. 2-23

CHAPTER 3 SOFTWARE UTILITIES

3-1 Introduction................................................................................ 3-2

3-2 Intel
3-3 Intel
3-4 Intel

®

Chipset Software Installation Utility…..…….................. 3-3

®

USB3.0 eXtensible Host Controller Utility...................... 3-4

®

Management Engine Components Utility........................ 3-5

3-5 VGA Driver Utility.................................................................... 3-6

3-6 LAN Driver Utility…………………………………………….. 3-7
3-7 Sound Driver Utility…………………………………………… 3-8
3-8 Touchscreen Driver Utility……………………………………. 3-9

CHAPTER 4 AMI BIOS SETUP

4-1 Introduction................................................................................ 4-2

4-2 Entering Setup............................................................................ 4-4

4-3 Main……................................................................................... 4-6

4-4 Advanced…………………….........................…....................... 4-7

4-5 Chipset…………….................................................................... 4-27

4-6 Boot..……………….................................................................. 4-35

4-7 Security………………………………………………………... 4-36
4-8 Save & Exit……………………………………………………. 4-37

APPENDIX A SYSTEM DIAGRAMS

Exploded Diagram for Basic Construction............................................ A-2

Exploded Diagram for Front Panel………............................................ A-3

Exploded Diagram for Mainboard…………………............................. A-9

Exploded Diagram for Heatsink Cover………...................................... A-11

Exploded Diagram for HDD…………...………................................... A-13

!

Contents

APPENDIX B TECHNICAL SUMMARY

Block Diagram...................................................................................... B-2

Interrupt Map......................................................................................... B-3

DMA Channels Map……...................................................................... B-8

I/O Map................................................................................................. B-9

Watchdog Timer Configuration…………..…………………………... B-13
Flash BIOS Update……………………………………………………. B-15

!

!

INTRODUCTION!

This chapter gives you the information for this system. It

also outlines the System specification.

Section includes:

z About This Manual

z System Specifications

z Safety Precautions

!

!!

CHAPTER

1

!

Experienced users can skip to chapter 2 on page 2-1
for Quick Start.

Page:1-1

Chapter 1 Introduction

1-1. ABOUT THIS MANUAL

Chapter 1 Introduction

This chapter introduces you to the background of this manual, and the specifications
for this system. The final page of this chapter will indicate how to avoid damaging this
board.

Chapter 2 Hardware Configuration

This chapter outlines the component locations and their functions. In the end of this
chapter, you will learn how to set jumper and how to configure this card to meet your
own needs.

Chapter 3 Software Utilities

This chapter contains helpful information for proper installations of the VGA utility,
LAN utility, and Sound utility.

Chapter 4 BIOS Setup

This chapter indicates you how to set up the BIOS configurations.

Appendix A System Diagrams

This appendix gives you the exploded diagrams and part numbers of the system.

Appendix B Technical Summary

This appendix gives you the information about the Technical maps, Watchdog-timer
configuration, and Flash BIOS Update.

Page: 1-2

Chapter 1 Introduction

1-2. SYSTEM ILLUSTRATION

2KHL+HMDÐ/3Ða

Front View Rear View

Top View

Bottom View

Unit: mm

Page: 1-3

Side View Quarter View

Chapter 1 Introduction

Unit: mm

Page: 1-4

2KHL+HMDÐ/3Ða

Front View Rear View

Chapter 1 Introduction

T

op View

Bottom V

iew

Unit: mm

!!!!

!!!!

Page: 1-5

Side View Quarter View

Chapter 1 Introduction

Unit: mm

Page: 1-6

2KHL+HMDÐ/3Ða

Front View Rear View

Chapter 1 Introduction

Top View

Bottom View

Unit: mm

!!!!

!!!!

Page: 1-7

Chapter 1 Introduction

Side View Quarter View

I/O View

DIO LPT

LAN1 LAN2

USB3.0

VGA

Line
Out

Mic In

COM2 COM4

COM1 COM3

9-36V

DC

GND

Unit: mm

!!!!

!!!!

Page: 1-8

1-3. SYSTEM SPECIFICATION

System

CPU Support Intel

Chipset Intel® HM76/QM77

OS Support Microsoft Windows XP/7

®

Core™ 3rd Gen. Mobile i3/i5/i7 (rPGA-988)

processor on board

Chapter 1 Introduction

Memory Support

2 x 204pin DDR3 SO-DIMM, support DDR3/DDR3L
1600/1333/1066 up to 8GB/slot

Watchdog

1~255s Watchdog timer

Drive Bay 2 x 2.5” SATA HDD

Power Supply DC-in 9~36V

Front Bezel Aluminum

IP65 Front panel only

Mounting Type

Net Weight

Dimension

PT 15

PT 15
PT 17

PT 17
PT 19

PT 19
PT 15

PT 17
PT 19

VESA 100/Wall Mount

 7.5 kg
 9 kg
 11.5 kg
 408 x 308 x 128 mm
 448 x 352 x 136 mm
 471 x 396 x 131 mm

Certificate FCC/CE

I/O Ports

Serial Port

4 x COM ports (pin-9 is RI/5V/12V selectable):

 COM1/3/4 for RS-232
 COM2 for RS-232/422/485

USB 4 x USB 3.0

Parallel Port 1 x DSUB-25

VGA 1 x VGA

LAN 2 x LAN (10/100/1000 Mbps), support Wake-on-LAN:

 LAN1: Intel
 LAN2: Intel

!!!!

!!!!

®

82579LM

®

82583V

Page: 1-9

Chapter 1 Introduction

Audio High Definition:

 1 x Line-out
 1 x MIC-in

Digital I/O 1 x DSUB-25 (8in/8out)
Expansion slot  1 x Mini-PCIe slot (for WLAN module & 3G module)

 1 x SIM card slot
 1 x CFast card slot
 1 x PCIe(4x), 10W/slot max. (Optional)

Display

LCD Panel Size

Resolution

PT 15
PT 17
PT 19

PT 15
PT 17
PT 19

 15”
 17”
 19”
 1024 x 768 XGA 400nit LED backlight
 1280 x 1024 SXGA 350nit LED backlight
 1280 x 1024 SXGA 300nit LED backlight

Touchscreen ( 5W Analog resistive (USB interface)

Environment

Operation Temp.
(with ambient airflow)

 General: 0 ~ 45°C

 CFast card (Wide Temp. Grade, w/o

audio): 0 ~ 50°C

Storage Temp. -20 ~ 80°C

Humidity 10 ~ 90%

!!!!

!!!!

Page: 1-10

Chapter 1 Introduction

1-4. SAFETY PRECAUTIONS

Follow the messages below to avoid your systems from damage:

1. Keep your system away from static electricity on all occasions.

2. Prevent electric shock. Don’t touch any components of this card when the card is

power-on. Always disconnect power when the system is not in use.

3. Disconnect power when you change any hardware devices. For instance, when

you connect a jumper or install any cards, a surge of power may damage the
electronic components or the whole system.

!

!!!!

!!!!

Page: 1-11

HARDWARE

CHAPTER

2

CONFIGURATION

** QUICK START **

Helpful information describes the jumper & connector settings, and
component locations.

Section includes:

z Jumper & Connector Quick Reference Table

z Component Locations

z Configuration and Jumper settings

z Connector’s Pin Assignments

Page 2-1

Chapter 2 Hardware Configuration

2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE

JUMPER/CONNECTOR NAME

Clear CMOS Data Selection JP5

CFAST Voltage Selection JP8

COM Ports COM1, COM2, COM3, COM4

COM Ports RI & Voltage Selection JP15, JP16, JP17, JP18

COM2 RS232/422/485 Selection JP13

COM2 Auto Detect Selection JP12

Digital I/O Connector DIO1

Flash Descriptor Override Selection JP3

Front Panel Selection PWRBTN1, HDDLED1, SYSRST1,

PWRLED1

Internal Keyboard & Mouse Connectors KB1, MS1

Hardware Power Failure Selection JP7

JUSB Connector JUSB1

LAN Connectors LAN1, LAN2

Printer Connector LPT1

LVDS Connector LVDS1

LVDS Inverter Connector INV1

LVDS Panel Brightness Control JP21

LVDS Voltage Selection JP19

Power Input Connector PWR_IN1, ATX_PWR1

SATA & SATA Power Connectors SATA1, SATA_PWR1, SATA2,

SATA_PWR2

Audio Connectors AUDIO1, LINE_IN1

System Fan Connector SYS_FAN1

USB3.0 Connectors USB1, USB2

VGA Connector VGA1

SIM Card Slot SIM1

Page: 2-2

2-2. COMPONENT LOCATIONS

5

1

JP20

JP19

56

12

JP61JP5

1

SP1

12

JP10

87

1

KB1

1

MS1

JP21

Battery

1
234

2
1

DIO1

SO_DIMM2

20

19

JP3

1

1

JP4

210
19

USB5

®

Intel
HM76/
QM77

1

1

2

2

71

72

71

72

73

74

73

74

Intel® Core™
3rd Gen.
Mobile i3/i5/i7
(rPGA-988)

Chapter 2 Hardware Configuration

SIM1

14

1

M_PCIE1

LPT1

26
13

PWRBTN1

SIO

1

JP7

JP8

1

9

2

10

1

SYSRST1

1

PWRLED1

1

HDDLED1

11

JP9

1

1

12

1211

1

IR1

JP14

JP22

SYS_FAN1

203

204

B9

B1

A9

A1

LAN2LAN1

USB1

B1

A9

A1

USB2

SO_DIMM1

203

204

9

10

JP13

LINE_IN1

5
10
15

VGA1

1

JP12

1
6
11

1

2

1

AUDIO1

21 24

15

125

JP17

10

15

1

4

6

125

JP18

6

6

14

18

5

9

COM1/2

Connectors, Jumpers and Components Locations

JP15 JP16

1256125

10

18

15

1

9

6

COM3/4

6

14

5

ATX_PWR1

2

4

3

1

4

3

2

1

PWR_IN1

Page: 2-3

Chapter 2 Hardware Configuration

3&,B(

JCFAST1

S1S7PC1 PC17

INV1

LVDS1

JUSB1

SATA1

SATA_PWR1

SATA2

SATA_PWR2

6

1

1292

30

1192

20

7

1

1

7

1

1

Connectors, Jumpers and Components Locations

Page: 2-4

Chapter 2 Hardware Configuration

2-3. HOW TO SET JUMPERS

You can configure your board by setting jumpers. Jumper is consists of two or three
metal pins with a plastic base mounted on the card, and by using a small plastic "cap",
Also known as the jumper cap (with a metal contact inside), you are able to connect
the pins. So you can set-up your hardware configuration by "open" or "close" pins.

The jumper can be combined into sets that called jumper blocks. When the jumpers
are all in the block, you have to put them together to set up the hardware configuration.
The figure below shows how this looks like.

JUMPERS AND CAPS

If a jumper has three pins (for examples, labelled PIN1, PIN2, and PIN3), You can
connect PIN1 & PIN2 to create one setting by shorting. You can either connect PIN2
& PIN3 to create another setting. The same jumper diagrams are applied all through
this manual. The figure below shows what the manual diagrams look and what they
represent.

Page: 2-5

JUMPER DIAGRAMS

Chapter 2 Hardware Configuration

Jumper Cap
looks like this

2 pin Jumper
looks like this

3 pin Jumper
looks like this

JUMPER SETTINGS

1

1

1

2

Jumper Block
looks like this

2 pin Jumper close(enabled)

Looks like this

3 pin Jumper

2-3 pin close(enabled)

Looks like this

Jumper Block

1-2 pin close(enabled)

Looks like this

1

1

12

Page: 2-6

Chapter 2 Hardware Configuration

2-4. CLEAR CMOS DATA SELECTION

JP5 : Clear CMOS Data Selection
The jumper setting is as follows:

SELECTION JUMPER SETTINGS JUMPER ILLUSTRATION

1

Normal Open



-3

1

Clear CMOS* Close



-3

Note: Manufacturing Default is Normal.

*To clear CMOS data, user must power-off the computer and set the jumper to “Clear
CMOS” as illustrated above. After five to six seconds, set the jumper back to “Normal”
and power-on the computer.

2-5. CFAST VOLTAGE SELECTION

JP8 : CFast Voltage Selection
The jumper setting is as follows:

SELECTION JUMPER SETTINGS JUMPER ILLUSTRATION

3.3V 1-2

5V 2-3

Note: Manufacturing Default is 3.3V.

31



-3

31



-3

Page: 2-7

Chapter 2 Hardware Configuration

2-6. COM PORTS

COM1, COM3, COM4: COM Ports, fixed as RS-232
The pin assignments are as follows:

PIN ASSIGNMENT PIN ASSIGNMENT

1 DCD# 6 DSR#

2 RX 7 RTS#

3 TX 8 CTS#

4 DTR# 9 RI#

5 GND

COM2: COM2 Connector, selectable as RS-232/422/485
The pin assignments are as follows:

PIN

ASSIGNMENT

RS-232 RS-422 RS-485

1 DCD# TX- RS-485­2 RX TX+ RS-485+
3 TX RX+ X
4 DTR# RX- X
5 GND GND GND
6 DSR# X X
7 RTS# X X
8 CTS# X X
9 RI# X X

1

6

&20

&20

&20

&20

5

9

Page: 2-8

Chapter 2 Hardware Configuration

2-7. COM PORTS RI & VOLTAGE SELECTION

JP18, JP17, JP16, JP15: COM1/2/3/4 Ports RI & Voltage Selection
The selections are as follows:

JUMPER ILLUSTRATION SELECTION JUMPER

SETTING

COM1 COM2 COM3 COM4

RI 1-2

VCC12 3-4

VCC 5-6

Note: Manufacturing Default is RI.

5
6

-3

5
6

-3

5
6

-3

1
2

1
2

1
2

5
6

5
6

5
6

-3

-3

-3

1
2

1
2

1
2

5
6

5
6

5
6

-3

-3

-3

1
2

1
2

1
2

5
6

5
6

5
6

-3

-3

-3

1
2

1
2

1
2

Page: 2-9

Chapter 2 Hardware Configuration

2-8. COM2 RS-232/422/485 SELECTION

JP13: COM2 RS-232/422/485 Selection
The selections are as follows:

SELECTION JUMPER SETTINGS JUMPER ILLUSTRATION

1
2



RS-232 All open

9

10

 -3

1
2



RS-422 1-2, 3-4, 9-10

9

10

 -3

1
2



RS-485 1-2, 5-6, 7-8

9

10

Note: Manufacturing Default is RS-232.

 -3

Page: 2-10

Chapter 2 Hardware Configuration

2-9. COM2 AUTO DETECT SELECTION

JP12: COM2 Auto Detect Selection
The selections are as follows:

SELECTION JUMPER SETTINGS JUMPER ILLUSTRATION

31

Normal 1-2



-3

31

Auto 2-3



-3

Note: Manufacturing Default is Auto.

2-10. DIGITAL I/O CONNECTOR

DIO1: DIO Connector
The pin assignments are as follows:

PIN ASSIGNMENT PIN ASSIGNMENT

1 VCC5 11 DIN5

2 VCC12 12 DOUT5

3 DIN1 13 DIN6

4 DOUT1 14 DOUT6

5 DIN2 15 DIN7

6 DOUT2 16 DOUT7

7 DIN3 17 DIN8

8 DOUT3 18 DOUT8

9 DIN4 19 GND

10 DOUT4 20 GND

202

119

',2

Page: 2-11

Chapter 2 Hardware Configuration

2-11. FLASH DESCRIPTOR OVERRIDE SELECTION

JP3: Flash Descriptor Override Selection
The selections are as follows:

SELECTION JUMPER SETTINGS JUMPER ILLUSTRATION

1

Disable Open



-3

1

Enable Close



-3

Note: Manufacturing Default is Disable.

Page: 2-12

Chapter 2 Hardware Configuration

2-12. FRONT PANEL CONNECTORS

PWRBTN1: ATX Power Button Connector
The pin assignments are as follows:

PIN ASSIGNMENT

1

PWR_BTN

2 GND

HDDLED1: Hard Disk Drive LED Connector
The pin assignments are as follows:

PIN ASSIGNMENT

1

HDD_LED+

2 HDD_LED-

SYSRST1: Reset Connector
The pin assignments are as follows:

PIN ASSIGNMENT

1
2 GND

RST_BTN

1
2

3:5%71

1
2

+''/('

1
2

PWRLED1: Power LED Connector
The pin assignments are as follows:

PIN ASSIGNMENT

1

PWR_LED+

2 GND

6<6567

1
2

3:5/('

Page: 2-13