TKT 5 Tier Heavy Duty Chipboard Shelving Assembly Instructions Manual

5 TIER HEAVY DUTY CHIPBOARD SHELVING

Assembly instructions

01 / 17

DESCRIPTION OF SIGNAL WORDS

WARNING indicates a hazardous
situation that, if not avoided, could
result in death or serious injury.

CAUTION indicates a hazardous
situation that, if not avoided, could
result in minor or moderate injury.

NOTICE indicates information
considered important, but not
hazard related (e.g. messages
related to property damage).

The arrows indicate work steps you have to take.

5 Tier Heavy Duty Chipboard Shelving

Introduction

Congratulations on the purchase of your new
shelving unit. You have purchased a high-quality

shelving unit. Please familiarize yourself with the
shelving unit before assembling it. Read and follow these
assembly instructions and the safety messages. Only use
the shelving unit as specied and for the indicated pur­poses. Keep these assembly instructions in a safe loca­tion. If you pass the shelving unit on to others, always
include these assembly instructions.

Contents / Parts Description

8 x 1 Upright
10 x 2 Cross piece (35.59 inch x 20.67 inch/

904 mm x 52.5 mm)

10 x 3 Cross piece (17.48 inch x 20.67 inch/

444 mm x 52.5 mm)
8 x 4 Connector piece
8 x 5 End cap
5 x 6 Shelf
2 x 7 Countersunk head screw (6 x 1.97 inch/6 x 50 mm)
2 x 8 Plain washer
2 x 9 Dowel

1 2 2

9 8 7

3

3

5 46

Intended Use

The shelving unit is intended for storage. The shelving
unit is only intended for private indoor use. Use only the
enclosed mounting hardware and never modify the shelv­ing unit since this can result in injuries and / or damage the
shelving unit. The manufacturer assumes no liability for in­juries and damage due to improper use. The shelving unit
is not intended for commercial use.

Never leave children unattended! The shelving

unit is not intended for climbing or playing! Do not allow

people, especially children, to climb on or lean against
the shelving unit. This may result in death, injuries
and / or damage.

AFTER SALES SUPPORT

Model: 5 Tier Heavy Duty Chipboard Shelving

Dimensions / Material

The heavy duty shelving unit can be assembled
vertically or horizontally.

Vertical assembly:

Horizontal
assembly:

Material:

Shelves: wood
Braces, connectors,
crossbars: metal

305 704 3882 www.tkt-usa.com

36.22 x 70.86 x 18.11 inch /
92 x 180 x 46 cm

70.86 x 36.22 x 18.11 inch /
180 x 92 x 46 cm

5 TIER HEAVY DUTY CHIPBOARD SHELVING

Assembly instructions

01 / 17

Corner brackets: plastic
Maximum weight: 385.80 lbs / 175 kg per shelf

Safety Notices

KEEP ALL SAFETY MESSAGES AND INSTRUCITONS
FOR FUTURE REFERENCE!

–

Never leave children unsupervised with the

packaging material. Suffocation hazard. Keep
the shelving unit out of the reach of children. The shelving
unit is not a toy.

– Make sure you will not be drilling into electrical, gas or

water lines inside the wall. Death or injury due to elec-

tric shock may otherwise result!

– Always wear safety gloves to protect hands

from cuts, pinching and bruising.

– Verify that all assembly hardware is undamaged and

the shelving unit is assembled correctly.

shelving unit may otherwise tip, possibly resulting
in death or injuries!

– Before anchoring, verify the wall will support the shelv-

ing unit. When in doubt, consult a licensed contractor.

The shelving unit may otherwise tip, possibly
resulting in death or injuries!

– Wall-mounting hardware (7, 8) suitable for standard

solid brickwork are included. The type of screw required
varies by wall construction. Always use screws and
mounting hardware suitable for the actual wall. Other-

wise the shelving unit may tip potentially resulting
in death or injuries!

Assembly

The heavy duty shelving unit can be assembled vertically or
horizontally.

–

385.80 lbs

or damage.

– The post with the weight limit must be installed in plain

sight (front). Exceeding the weight limit may cause

the shelving unit to collapse or tip, resulting in
death, injuries and / or damage to the shelving unit!

– Make sure the person assembling the shelving unit has

read the assembly instructions. If assembled incor-

rectly, the shelving unit may collapse or tip, result­ing in death or injuries!

– Always set up the shelving unit on solid, level ground.

The shelving unit may otherwise tip, possibly re­sulting in death or injuries!

– Verify the shelving unit is sturdy before using it.

The shelving unit may otherwise collapse or tip,
possibly resulting in death or injuries!

– Always spread the load evenly – do not overload.

The shelving unit may otherwise collapse or tip,
possibly resulting in death or injuries!

– After assembly, verify all parts are connected rmly.

The shelving unit may otherwise collapse or tip,
possibly resulting in death or injuries!

– Anchor the shelving unit securely to the wall! The

Never exceed the maximum load of 385.80 lbs

per shelf. Otherwise the shelving unit might

break or collapse and cause death, injuries

vertical horizontal

Assembly and anchoring in the wall

You will need the following tools (not included):

· Philips head screwdriver

· Power drill

· for brick walls: ⅜ masonry bit

· for walls with studs (2 x 4): 1/8 wood drill bit

· Rubber mallet

Vertical assembly
Step 1

– Always wear safety gloves to protect hands

from cuts, pinching and bruising.

Attach corner brackets 5 to the posts 1 to

prevent scratching the oor.

Attach 2 long crossbars 2 and 2 short crossbars 3 to

the posts 1 by inserting them in the designated notches
and carefully tapping in place with a rubber mallet.

AFTER SALES SUPPORT

Model: 5 Tier Heavy Duty Chipboard Shelving

305 704 3882

www.tkt-usa.com

5 TIER HEAVY DUTY CHIPBOARD SHELVING

Assembly instructions

01 / 17

Step 1

1

2
5

2

3

5

When installing the crossbars 2, 3, make sure the

support edge for the shelves 6 is facing up. Installing the
crossbars incorrectly may affect the safety and function.

damage to the shelving unit because the shelving unit
may tip over or collapse.

Step 3

Now install the remaining crossbars 2, 3 at the de-

sired height as described in step 1.

Step 3

1

2

Horizontal assembly
Step 1

Step 2

Install the connectors 4 into the posts 1 from the top

and tap in place with a rubber mallet. Install another
post 1 on each connector 4 and carefully tap in place
with a rubber mallet.

Step 2

4

1 1

– Install the post 1 with the weight limit sticker so that

the weight limit sticker is visible from the front. Exceed­ing the weight limit may result in death, injuries and / or

– Always wear safety gloves to protect hands

from cuts, pinching and bruising.

Attach corner brackets 5 to the posts 1 to

prevent scratching the oor.

Attach 2 long crossbars 2 and 2 short crossbars 3 to

the posts 1 by inserting them in the designated notches
and carefully tapping in place with a rubber mallet.

Step 1

1

2
5

2

3

5

AFTER SALES SUPPORT

Model: 5 Tier Heavy Duty Chipboard Shelving

www.tkt-usa.com 305 704 3882