Queue Wireless Calling System User Manual
Product introduction:
Thanks for using our company's wireless calling system, it adopts RF wireless technology with
millions of different learning codes. The system consists of 1 call button keypad and 20 portable
receivers, the receiving pager supports 999-channel extensions, the call button keypad has 20
battery charging slots. Each receiver is rechargeable and labeled with a number, in standby status,
it is plugged into the charging slots, while the guest places an order, he(she) will be dispatched
one receiver with a number, when the order is ready, the waiter will press the keypad to call the
number, the guest will get it through the buzzer/vibration/LED indications.
The queue system greatly improves the work efficiency and avoid the guest waiting in a long
queue. It is widely used in fast food restaurant, church, dessert shop, auto 4S shop, food truck or
other queue occasions.
The diagram of the call button keypad
接收器：Receiver
广告贴纸：Number paper
电源：Power in
天线：Antenna
充电插槽：Charging slot
呼叫键盘：keypad area
The diagram of the receiver
透明片：Transparent cover
广告贴纸：Number paper
指示灯：LED
广告纸：Paper slot
录码：Pair
模式：Mode
正面：Front
复位：Power on/off Reset
侧面：Side
背面：Back
内置电池：Built-in battery
充电脚：charging pins
Technical data
Receiver
Working voltage
DC 3.7V (Rechargeable battery)
Charging voltage
DC 5V
Working frequency
433.92MHz
Standby current
10±5mA
Working current
100±20mA(Max.)
Receive sensitivity
-107±2dBm
Battery capacity
360mAh
Decoder
Learning code (AM)
Dimension
104*50*8mm
Keypad call button
Working voltage
DC 5V/8A
Working frequency
433.92MHz
Standby current
24±5mA
Transmit current
100±30mA
Encoder
Learning code (AM)
Dimension
280*158*34mm
Operation instruction
1. Open the package, connect the call button keypad to power, it executes the self-testing
procedure, then power icon turns on.
2. When guest places an order, the service people give one receiver to him(her) and note down
the number.
3. While the order is ready, the waiter press keypad to call the guest (number), the
corresponding receiver gets the information and prompts vibration/buzzer/light for 5 min,
remind the guest to complete the order.
4. At last, the guest returns the pager to the waiter and the service is completed.
Function Description:
1. The keypad call button is connected to the power supply through the power adapter, host
digital screen display“000”, the pager is inserted into the charging slot of the host, the pager is
opened and charged, and the red light of the pager indicator is often lit.
2. After the charge of the pager is full, the indicator light is shown to be a green light.
3. After the pager is taken out, the pager enters the waiting call state, indicating that the light
yellow light flashes once every 3sec.
4. When the host is called, the pager receives the call information. It flashes every 0.5sec by
vibrant, buzzing and yellow lights for reminding.
5. The pager reminding time is 30 sec, can short press the side button of the pager to close the
reminder, or insert the host charging slot to close the reminder.
6. The pager in the charging process, when the host call, the light yellow light of reception
indicator flashes every 0.5 sec for a reminder.
7. When the power of the pager is low, the red light of the indicator is flicker once every 1sec.
8. When the pager is inserted into the host charging slot, press 999 on the keypad call button
and then press the call key, the pager in all the charging slots can be turned off.
Pairing method
1. Pairing - The pager is in standby state, short press the“Set”button, the yellow indicator light
of the receiving pager is always bright, then press the call number on the keypad, the pager gets
the signal and yellow lamp turns off and accompanied by buzz and vibration reminding, which
represents the success of the code.
2. Deleting - The pager is in standby state, press and holds on the “Set” button for 5 sec, the
receiving indicator light goes from yellow to extinguish, then release the button, all the paired
call buttons will be deleted.
Reminder mode switching:
The receiving pager is in the standby state, short press the mode button on the pager, change the
reminder mode. There are four kinds of modes, the default is the vibration, the buzzing, and the
LED lights, the other three are Vibration and buzz; Vibration plus light; Beep and lamplight.
Four mode cycle switching, when switching to the corresponding mode, the receiving card shall
remind the time 5 sec according to the corresponding reminder mode.
Change number paper
Take out the transparent plexiglass cover in the front of the pager, then put a numbered paper
inside the paper slot, and then put back the cover.
Note: While doing the pairing operation, take out the cover and paper firstly.
FAQ
Problems
Reasons
Solutions
While power on, the number
display on keypad is not on.
The power adaptor is broken.
Change the power adaptor.
The distance of some pager
gets near.
The power of battery is low.
Charge the battery in time.
Pager cannot get any signal
from keypad call button.
The pairing is deleted; The
number is not correct.
Pair the pager again to the
keypad.
Forget the number of pager
Delete the pairing first, then
pair it again.
Package list
Name
Quantity
Call button keypad
1 pc
pager
20 pcs
Power adaptor
1 pc
User manual
1 pc
Warranty card
1 pc
Loading...