titathink TT520PW, TT521PW, TT522PW, TT6x0W, TT6x0CW Quick Manual

...

Quick Guide

Titathink IP Cameras

TT520PW / TT521PW / TT522PW

TT6x0W / TT6x0CW

TT7x0PW / TT7x0LPW

TT52xG / TT52x-LTE / TT8x0G / TT8x0-LTE

Standard & Pro Version

Includes: Camera unit / Power Adapter / Mounting bracket / Antenna / Manual

Ethernet Cable / Screws

1-1. Interfaces for Spy Series 1-2. Interfaces for Indoor Series 1-3. Interfaces for Outdoor Series 1-4. Interfaces Description

2-1. Initialized Connection for Spy Series 2-2. Initialized Connection for Indoor Series 2-3. Initialized Connection for TT7x0PW

Reset DC 12VLANI/O

General I/O

TT520W / TT520PW TT521W / TT521PW

The length of the camera cable is 20 feet. Please don't extend this cable more than 38 feet!

Lens unit

TT6x0W

TT7x0PW

TT7x0LPW / TT8x0G

TT7x0LPW / TT8x0

TT7x0PW

TT6x0W TT6x0CW

TT52xPW

TT6x0CW

Base unit

TT522W / TT522PW TT525PW

LAN Port Reset Button DC Power Socket

NOTE: The SD card slot is built in the inner of camera body. Please see the connection figures to check. The Reset button of TT7x0LPW / TT8x0G can also be found in the inner of camera body.

Line-in / MIC

CAM

Micro SD

Line-in / MIC

CAM

Micro SD

SIM Card Slot

This slot is only built in 3G/4G hidden cameras: TT52xG / TT52x-LTE (x means 0/1/2/5).

Microphone Jack

RJ11 CAM Port

Warning: Ensure the camera cable good contact to this port, otherwise, the camera will show you a black screen.

Micro SD Card Slot

WiFi Antenna Socket

WiFi Antenna

Camera cable

LAN cable

NOTE: The external microphone must require an external power adapter. This should come with the microphone.

Lens unit

Main unit

Power adapter

Explore more details of connection

External Microphone

Router

Connect to router just for initialized

setup. (Recommended)

After setup, disconnect this cable

to let camera work via Wi-Fi.

！

Warning: TT525PW doesn't have the jack because it has a built-in microphone in its lens unit.

！

Reset Button

DC Power Socket

This interface is used to connect external alarm devices such as:

1. PIR sensor

2. Gas detector

3. etc.

+12V DO DI GND

After the camera is turned on, by pressing the button 10 seconds at least then release, the camera will erase all of the previous settings and restore it default settings.

This indicated light is used to state the working status. Please see the section "1-5. Check Power Indicated LED".

The light sensor determines whether turning on/off night vision feature.

The provided power adapter should be plugged into this power socket. It requires DC 12V, 1A power source.

LAN Port

This port is RJ45 jack and requires an LAN cable for the initialized setup. Or stay connected via Ethernet cable as:

1. Wired connection.

2. PoE connection.

NOTE: Don't plug the camera cable into the LAN port if the camera is TT520, TT521, TT522 (Standard & Pro version). NOTE: TT6x0W, TT6x0CW don't support PoE connection.

！

A famale style of RCA audio line-in port. It requires an external CCTV microphone which has a male RCA plug.

No need further setup, just plug-and-play.

A 3.55mm headphone jack. It requires standard headset plug so it can be connected to a speaker / headset to broadcast the sound.

RJ11 CAM Port

The provided lens unit part must be connected to this CAM port.

Warning: Ensure the camera cable of lens unit good contacts to the CAM port, otherwise, the camera will show you a black screen.

This slot is used to carry a micro SD card to store video files. The SD card must meet requirements below:

1. The capacity up to 128Gb.

2. Class 4 or better.

3. Must be FAT32 format.

！

3. You will also need

1-5. Check Power Indicated LED

Internet

********

Password:

A Smart Device

Smartphone such as iPhone or Samsung or other Android phone.

Tablet such as iPad or Android tablet.

Your Wi-Fi Password

The password of Wi-Fi broadcasted by the same router which the camera is plugged into.

The smart device have to install an APP called Anyscene. This app is available to download on Google Play and Apple APP Store.

By searching the "Anyscene" on Google Play or APP Store, you will be able to install the app onto your smart device.

Anyscene

Ensure you have finished the above steps before get started setting up the camera.

We assume the name of WiFi network being broadcast is TOTOLINK.

Next, make sure your phone has been connected to the Wi-Fi "TOTOLINK".

WARNING: *This should be the same Wi-Fi network being broadcast from the same router.

*This Wi-Fi network cannot be an invisible Wi-Fi network due to the camera can not join it.

Run the Anyscene APP on the phone.

Tap "Add" or button to add your camera.

Tap "Search" button to discover your camera. For the Android phone, Tap "Scan local network"

Tap the listed UID number to add camera. If there is nothing found, you need to recheck the wired connection between camera to router.

4-1. Quick Setup to Smartphone

RESET

POWER

RESET

Light Sensor

DC Power Socket

General I/O

Microphone Jack8

LAN Port

Infrared

LEDs

Infrared

LEDs

Infrared

LEDs

Infrared

LEDs

Light Sensor

LAN Port

Audio Line-out

9 10

Audio Line-out

DC Power Socket

DC Power

Socket

Speaker

WPS LED

WPS Button

Reset Button

Microphone

Power

Indicated

LED

Power Indicated LED

Power

Indicated

LED

Power

Indicated

LED

Power Indicated LED

Power

Indicated

LED

Lens

Micro SD Card Slot

SIM Card Slot

(Only for TT8x0G/LTE)

SIM Card Slot

RESET

Warning: Don't plug camera cable into LAN port!

！

The SIM card must be provided by the mobile carrier of your country.

POWER

Black status:

No power or the indicated LED was disabled on app.

Keep green status:

Camera is starting up, please waiting.

Green flashing:

Camera is working properly and is standby.

Green fast flashing:

Someone visits the camera.

POWER

Power adapter

LAN cable

Router

Connect to router just for initialized setup. (Recommended)

After setup, disconnect this cable to let camera work via Wi-Fi.

Directly connect to PC if there is no router.

For more details, please see

"Setup via Computer".

Internet

Micro SD

Two ways to set up the camera

Router

RouterPCPC

Connect to router just for initialized setup. (Recommended)

After setup, disconnect this cable to let camera work via Wi-Fi.

Directly connect to PC if there is no router.

For more details, please see "Setup via Computer".

Internet

2-4. Initialized Connection for TT7x0LPW / TT8x0G / TT8x0-LTE

Setup via Computer

Power adapter

LAN cable

Router

Connect to router just for initialized setup. (Recommended)

After setup, disconnect this cable to let camera work via Wi-Fi.

Directly connect to PC if there is no router.

For more details, please see the "Setup via Computer".

Internet

Router

Directly connect to PC if there is no router.

For more details, please see "

Setup via Computer".

Camera requires setup before using, you need to follow next sections to use the provided LAN cable to connect to a router or a computer first.

After setup is completed, you can disconnect the LAN cable to let camera work on wireless mode.

！

Before you get started setting up the camera to connect a Wi-Fi network, you need to make sure the Wi-Fi SSID is not 5GHz Wi-Fi network. Or the Wi-Fi setup will be failure.

Next sections will guide you how to add camera to Anyscene app and set up the WiFi connection. The guidance of next sections will base on the case which that the camera connects to the router (Not computer).

Micro SD

SIM

NOTE: This SIM card slot is only built in TT8x0G or TT8x0-LTE

You may have no a router to set up the camera, there is another way to set up camera. You need to prepare a computer which has a LAN port as well.

Please refer to following steps to set up the camera via a computer.

You need to change the IP address of computer to 192.168.168.200

Connect the camera to the LAN port of computer via LAN cable. Power on camera and wait about 1 minute then go ahead.

Open a browser and enter http://192.168.168.100. You will get the welcome page of the camera. *If the welcome page can not be showed, please use Chrome or Safari to try again, meanwhile, please lower the security level of browser and ensure the firewall doesn't block the camera.

Enter the username and password to login. (The default username and password are both 'admin').

You can browse the right sidebar to see "Network"->"Wireless Setup"-> You can set up the WiFi for camera in that page.

For more details, please visit:

http://support.titathink.com/docs/titathink-hidden-cameras/ setup-via-web-application/1-access-web-application/#access-web-without-router

After you have done, please disconnect the LAN cable between camera and computer, then camera will be able to work wirelessly. You can follow next sections to add camera to your mobile devices.

IF YOU HAVE A ROUTER, PLEASE SKIP THIS SECTION AND JUST CONNECT THE CAMERA TO THE ROUTER VIA A LAN CABLE.

Titathink Cameras

Open

Lock

Open

See the

reverse side

POWER

GND

！

4-3. Quick Setup to Smartphone (For Cellular IP Camera TT52xG / TT8x0G)

4-2. Quick Setup to Smartphone (For WiFi IP Camera TT52xPW / TT6x0W/ TT6x0CW / TT7x0PW / T T7x0LPW) 4-4. The FAQ for Setup

Enter password and tap tap "Save" on the right top of screen. Your camera is successfully added to your phone.

The default password is "admin"

Ensure it says "Connected", then tap the camera the arrow left icon to wake up the tool bar.

Tap the edit icon to access the advanced setting page.

Your camera now is listed on Anyscene app. Tap the camera to view. Now the camera is working on wired connection mode.

Ensure it says "Connected" or "Online", then tap the camera to start watching the live footage.

Tips:

You are now ready to watch the camera.

Warning: Don't disconnect the wired connection between camera to router, or you will lose the live footage.

Please follow next steps to set up camera to connect to cellular network.

！

Warning: The field of Phone number must be entered to *99#. The 3G dial-up option must be turned on.

！

Warning: If there is a failed message, please recheck if your camera has been inserted a 3G SIM card. And please move the camera nearer to open areas like windowsill where can receive a good signal.

Connected / Online. The camera has connected to phone successfully. Connecting. The camera is trying to communicate to phone.

Disconnect. The camera lost connection to your phone.

Record the Local URL and type it to a browser. This browser can be the phone browser or PC browser.

For example, the local url is

192.168.106:80

Enter it to a browser:

Warning:

The browser can be Firefox, Safari, Chrome, IE.

If you plan to use PC browser, please make sure the PC is connected to the same router.

#10

Go to About Device interface.

You will go to welcome page. Please click "Setting" button.

Please enter your camera username and password (Default are both admin) to assigned field.

#11

Browse the right sidebar to access "3G Setup" page.

#12

Enter your 3G SIM card information here. APN / Username / Password should be provided by the carrier. The Phone number must be *99# . Next, refer below screenshot to set up the rest of settings. Then click "Apply" button to save.

#13

Click "Hardware Test" to test both the 3G module of camera and 3G SIM card to check if working properly.

You're done. After you disconnect the Ethernet cable, your camera will be able to work via cellular network.

#14

！

Enter password and tap "Connect". If it says connected, your camera is successfully added to your phone. If you want camera work on wired mode, just tap "Save" and ignore next steps.

The default password is "admin"

Tap "Setup WiFi" to setup WiFi connection.

Select the WiFi SSID you own.

Ensure the WiFi strength > 70% and the WIFI SSID is not 5GHz WiFi.

Enter your WiFi password carefully and note the case sensitive.

Tips:

The blue dot indicates the camera has set up WiFi successfully.

The red dot indicates the WiFi set up failed. You have to check if the WiFi password is correct or not. Make sure the WiFi password doesn't include special characters like & ` #@, etc. If you ensure the password is correct, please make sure the WiFi is not 5G WiFi.

Back to previous page, and tap "Save" to finish the adding operations.

Your camera now is listed on Anyscene app. Tap the camera to view.

Tips:

You are now ready to use the camera.

Unplug the LAN cable then your camera will work on WiFi mode.

Warning: If you got no video and black screen, please replug the lens unit to main unit several times. A poor contact may cause this issue.

Still need more helps, please see the provided manual to get more information.

Or you can visit Titathink support website: http://support.titathink.com

Or send us an email: support@titathink.com

Connected / Online. The camera has connected to phone successfully.

Connecting. The camera is trying to communicate to phone.

Offline. The camera lost connection to your phone.

Mounting instruction for TT520

Mounting instruction for TT7x0PW

Mounting instruction for TT7xLPW / TT8x0G / TT8x0-LTE

Wall Mounting Bracket

Pinhole Mounting Bracket

Wall Mounting Bracket

Fix the lens unit to a wall

Assemble the bracket for the lens unit

Mount the lens unit to the a pinhole of door plank

Mounting instruction for TT521

Wall Mounting Bracket

Assemble the bracket for the lens unit

The maximum depth of water

can reach up to 7 feet.

Mounting instruction for TT522 Mounting instruction for TT525PW

OUTDOOR

INDOOR

DOOR

Pinhole

OUTDOOR

INDOOR

OUTDOOR

INDOOR

Wall Mounting Bracket

Assemble the bracket for the lens unit

OUTDOOR

INDOOR

Roof gutter / Eave

Wall

5. Mounting Instruction for Spy Series

6. Mounting Instruction for Outdoor Series

lock

open

Warning: Extension plug must inject first, then lock the metal ring. If the extension box can not be connected properly, you may be unable to use the camera.

Metal ring

(1). Assemble the rain-proof cover. (2). Assemble the antenna.

(3). Connect to extension box.

(4). Lock the extension box.

Extension plug

Mounting nut

Mounting screw

LAN cable

Speaker line

Power line

Waterproof box

LAN cable

Power line

Waterproof box

Extension box

The hidden camera is black screen with a loading icon after finished the setup.

This issue may be caused by two cases:

1. Please check what app says first. If it says "Connecting" or "Offline", please check the connection between camera to router to ensure the WiFi network or LAN cable is good working. Or try to reboot the router and camera once time.

2. If the app says 'connected' or 'online', the lens unit may poor contact to main unit. Please shut down the camera and replug the camera cable serveral times.

First of all, please make sure the selected WiFi network is not belong to 5Ghz WiFi network, all of cameras are only able to work with standard 2.4Ghz WiFi network. Next make sure the signal intensity of received WiFi is not less than 60%. You can retry to configure the WiFi setting. The WiFi password is case sensitive.

Please make sure the SD card is plugged into the camera properly. Then make sure the SD card is FAT32 format system and its capacity doesn't exceed 128Gb, otherwise, the camera will be unable to recognize the SD card to cause the camera can not read-and-write to the SD card.

The camera can not work with following kinds of WiFi SSID:

1). 5Ghz WiFi network.

2). WiFi SSID is invisible network that requires manually enter the WiFi name.

3). The WiFi is network portal that requires a phone registration. If you are sure the WiFi is not belong to the above kinds, Please move the camera closer to the router and try again.

It requires that the camera connects to a router via a LAN cable. Then make sure the end of LAN cable is plugged to the LAN(RJ45) port, and the other end of the LAN cable is plugged to the LAN port of the router. If the problem still remains, please ensure the router you used doesn't limit the MAC address.

This issue may be caused by two cases:

1. the lens unit may poor contact to main unit. Please shut down the camera and replug the camera cable serveral times.

2. If you have tried to replug the lens unit, but the issue still remains, the lens unit may be broken. Please find the contact information in the manual to contact us.

Please check if your router has Internet access first, then check if the camera can be viewed in local area network, if not, please re-follow the quick guide to set up the camera again.

When night vision feature is turned on, the picture will be showed with black-and-white mode. In default setting, the camera will automatically switch the night vision to on or off by depending on the light around the camera. So you can move the camera to a bright area then it will back to color mode.

Just disconnect the LAN cable from the camera then camera will automatically switch on the WiFi mode.

The WiFi module will standby when camera is working on wired connection.

If your camera is not TT525PW, you need to connect an external microphone for the camera to pick up the sound. It's plug and play, you don't need to set up any setting for the external microphone.

Please go to http://support.titathink.com to learn more about which kind of microphone you should purchase.

If you get the camera recording continuously to the memory card, and the memory card is a true 128 GB memory card (131,072 MB), the camera should be able to record for roughly 72 hours.

The highest quality setting is 4096 Kb(bit)/second video + 40 Kb(bit)/s sound = 517 KB(Byte)/second, which calculates to 30.3 MB/minute. If you get the camera recording only when it senses motion, then the number of hours of monitoring will depend on both the number of motion detection events and the length of recording that you select when motion is detected.

According to the above, a 128 GB card might be sufficient for a month of motion detection recording, or just over 72 hours depending on the environment where the camera is located.

In default, the camera uses secondary stream as the live viewing streaming and records primary stream onto SD card. You need to go to the Advanced setting" in the app to turn on "HD viewing" option. please refer the provided manual to find this option.

Sometimes, the cellular network may be blocked by walls, buildings so the camera can not receive a stable cellular network.

Please move the camera body closer to an open area like window which that camera can receive stronger cellular signal.

The hidden camera shows you a green screen.

There is no video file recorded onto SD card.

How much time can you record onto 128Gb SD card.

The camera can not pick up the WiFi SSID.

The Anyscene app can not discover the camera when adding camera to the app.

After you entered the WiFi password, the camera always prompts error.

How the camera works on WiFi mode after completed the setup.

The picture is in black and white mode.

The TT8x0G / TT52xG camera can not work via cellular network although you get 'success' for "Hardware test"

Could not view the camera remotely You can not hear sound from hidden camera.

The quality of live footage is not as same as the recordings on SD card.

titathink TT520PW, TT521PW, TT522PW, TT6x0W, TT6x0CW Quick Manual

Specifications and Main Features

Frequently Asked Questions

User Manual