Titan Controls HyperioN 2 Instruction Manual

HyperioN

®

2

Wireless Environmental / Lighting

Master Controller

Instruction Manual

www.titancontrols.net

Product #702880

2

Hyperion® 2 Table of Contents

Overview ................................................................................................4

Figure 1: Control Network ....................................................................... 5

Quick Set Up Guide ..............................................................................6

Figure 2: Master Controller ......................................................................5

Control Description ..............................................................................7

Daytime and Nighttime Defined................................................................7

Wireless Communication .........................................................................7

Daytime Control .......................................................................................7

Controlling Relative Humidity (RH) ........................................................7

Controlling Temperature .......................................................................8

Controlling CO2 ...................................................................................8

Nighttime Control ....................................................................................8

Controlling Relative Humidity (RH) ........................................................8

Controlling Temperature .......................................................................8

Controlling CO2 ...................................................................................8

Lighting Control .......................................................................................9

Light Odometer Feature ..........................................................................9

Alternate Exhaust Daytime/Nighttime Control...........................................9

Controlling RH with Alternate Exhaust Feature Enabled ...........................9

Checking and Adjusting the Hyperion® 2 Settings ..........................10

Checking the Hyperion® 2 Control Parameters ......................................10

Figure 3: Hyperion® 2 Remote Control ...................................................10

Light Timing Adjustments ......................................................................10

Table 1: On Period Settings for Hyperion® 2 Lighting Control .................11

Resetting the Light Odometer (Change bulb icon) ..................................11

Setting the Current Time ........................................................................12

Battery Replacement .............................................................................13

Temperature Setting ..............................................................................13

CO2 and RH Settings .............................................................................14

Alternate Exhaust Mode ........................................................................14

Restoring Factory Default Settings .........................................................14

Codes and Errors ...............................................................................15

Over Temperature Shutoff ......................................................................15

High Temperature Condition ..................................................................15

Low Temperature Condition ...................................................................15

High Humidity Condition ........................................................................16

Low Humidity Condition ........................................................................16

High CO2 Concentration Condition ........................................................16

3

Empty CO

2

Tank Condition .....................................................................16

No Measured Light Condition ................................................................16

No Measured Darkness Condition .........................................................16

Lighting Schedule Interrupted Condition ................................................17

Temperature Sensor Error ......................................................................17

RH Sensor Errors ..................................................................................17

CO2 Sensor Error ...................................................................................17

Real Time Clock Error ............................................................................17

Table 2: Remote Control Remote Control Codes ...................................18

Remote Sensor LED ..............................................................................18

Table 3: Remote Sensor Module LED Codes .........................................19

Calibration ...........................................................................................20

CO2 Calibration .....................................................................................20

Figure 4: Bottom View of Remote Sensor ..............................................20

Hyperion® 2 Wireless Control Network ............................................21

Normal Operation ..................................................................................21

Wireless Control Network Error .............................................................21

Table 4: Remote Controller Network Messages......................................21

Remote Controller Behavior ...................................................................22

Remote Sensor Behavior ......................................................................22

Range Testing ........................................................................................22

Rebuilding the Wireless Network ..........................................................23

Installation Diagram ...............................................................................23

Factory Defaults and Control Limits .......................................................24

Temperature .........................................................................................24

Humidity ...............................................................................................24

CO2 .......................................................................................................24

Warranty Information .........................................................................24

Troubleshooting Tips .........................................................................26

Controller Specifications ..................................................................26

Service and Repair Program ............................................................27

4

Overview

Titan Controls® brings to you the most complete grow room controller
available in the industry today! The Hyperion® 2 features 4 – 240V AC
outlets for a garden lighting systems as well as a complete wireless
environmental controller. The Hyperion® 2 Controller uses three modules:
the remote sensor, master controller, and remote controller, to form a
wireless control network (refer to Figure 1). The Hyperion® 2 is equipped
with transceivers that operate in the non-licensed 2.4 GHz frequency band
and are FCC (USA), IC (Canada), and ETSI (Europe) compliant. The remote
sensor and remote controller communicate wirelessly and allow remote
monitoring and control of a room’s environment. All control parameters are
changed over the wireless network via the user interface.

The Hyperion® 2 remote sensor is equipped with CO2, relative humidity,
temperature, and light sensors. The room’s environment is controlled by
relay outputs located on the master controller. These outputs are used to
control ventilation fans, a dehumidification unit, a CO2 generator or CO2
regulator & tank system, and a 240V AC four light system.

Separate Daytime and Nighttime control parameters are used to keep the
room’s environment at optimum growing conditions throughout a 24-hour
period.

The Hyperion 2 is the complete solution to your indoor gardening
requirements!

5

120V AC

Circuit

Remote

Controller

Exhaust

Power: 40 Amps/240V AC/60Hz

Light

Exhaust
Output

6

Quick Set up Guide

The Hyperion® 2 Control is set up with default Daytime and Nighttime
control parameters that enable it to be used immediately out of the box. To
quickly set up the Hyperion® 2, follow these instructions (use Figures 1 and
2 for reference):

NOTE: For best results have Hyperion® 2 installed by a certified Electrician.

1. Mount the remote sensor in the desired location; be sure the photo

cell is directly exposed to the grow lights.

2. Mount the master controller in the desired location. Verify that the

breaker controlling this Hyperion® 2 is in the OFF position.

3. Plug the RJ-45 network cable into the master controller and remote sensor.

4. Plug equipment into the appropriate outputs of the master controller

(refer to Figure 2): - Ventilation fan to the output labeled ‘Exhaust
Output’. - Dehumidification gear into the output labeled ‘Dehumidify
Output’. - CO2 Generator or CO2 Regulator into the ‘CO2 Output’.
Finally, plug 240V AC ballasts into ‘240 Volt Power Output’ receptacles.

5. Provide power to the master controller; this will also provide power to the

remote sensor (via the network cable). The LED on the remote sensor
will flash yellow and begin controlling the room’s environment. The

yellow LED indicates that the remote sensor is searching for the remote

controller over the wireless network (refer to Table 3 in the Remote
Sensor Moldule LED section of this document for more information).

6. Bring the remote controller in close proximity to the remote sensor so

that both the display and the remote sensor’s LED (shown in Figure 1)
are visible. Plug in the power supply to 120V AC power; the display
will flash while it initializes and searches for the remote sensor over the
wireless network when the remote sensor and remote controller have
successfully established wireless communication, the remote sensor’s
LED will change from flashing yellow to flashing green as described
in Table 3. The remote controller will then stop flashing and begin
showing the current readings in the grow roomA.

7. Unplug the remote controller and move it to the desired location. The

Hyperion® 2 will continue to control the room’s environment even when
the remote controller is unpluggedB (refer to the Hyperion® 2 Wireless
Control Network section of this document for further information). To
test the signal strength of the Hyperion® 2’s control network refer to
Range Testing in the Hyperion® 2 - Wireless Control Network section of
this document.

A. If the modules are unable to link-up and form the control network, follow the Rebuilding the Wireless Network procedure in the Hyperion® 2
Wireless Control Network section.

B. A list of the Hyperion® 2 default control parameters is listed in the Factory Defaults and Control Limits section of this document. To make
adjustments to the Hyperion® 2 settings, refer to the Checking and Adjusting the Hyperion® 2 Settings section of this document.

7

Control Description

Daytime and Nighttime Defined

The remote sensor has a photocell that it is used to determine if the
controller will operate in Daytime or Nighttime mode. For the purpose of
this document, Daytime is defined as the time when the remote sensor
senses light and Nighttime is when it does not sense light in the room: The
actual time-of-day does not contribute to Daytime or Nighttime modes of
the Hyperion® 2 Control.

The Hyperion® 2 is preset with default Daytime and Nighttime control
parameters (shown in Factory Defaults and Control Limits section of this
document) that enable it to be used immediately out of the box.

Wireless Communication:

The Hyperion® 2 uses a wireless control network to communicate between
the sensor and remote controllers (shown in Figure 1). The Hyperion® 2
will control the room’s environment even if the wireless communication
between the two modules is interrupted (more details on the Wireless
Control Network are given in the Wireless Control Network section of this
document). Issues with the Wireless Control Network are reported by both
remote controller and remote sensor (refer to the Wireless Control Network
Issues description in the Hyperion® 2 Control Network section of this
document for further information).

Daytime Control:

The Hyperion® 2 uses the Daytime control parameters to keep its
environment at the desired levels. During the Daytime, the LED on the
remote sensor will be illuminated but will flash momentarily every three­seconds and the Hyperion® 2 remote controller will show the day symbol
for MODE in the upper right-hand corner.

Controlling Relative Humidity (RH):

If the room’s RH rises above the RH setpoint by the amount of the
hysteresis setting (the setpoint plus 2%), the Dehumidification output will
activate. This output will remain on until the room’s RH drops below the
setpoint setting (the setpoint minus 2%).

Controlling Temperature:

If the temperature climbs above the desired setpoint by the amount of the
hysteresis setting (the setpoint plus 3° F), the controller will defeat the CO2
output and activate the Exhaust output. The exhaust fan will remain on and
the CO2 will remain off until the temperature falls below the setpoint by the
hysteresis setting amount (setpoint minus 3° F): at this point the controller
will then turn off the Exhaust output and allow the CO

2

output to control as

described in the following Controlling CO2 section.

8

Controlling CO2:

During the Daytime, when the CO2 reading drops below the setpoint
minus the hysteresis (the setpoint minus 100 ppm), the CO2 output will
be activated. The CO2 output will remain on until the reading rises to the
desired setpoint. When the CO2 reading reaches the setpoint the output
will then turn off. Each time the Exhaust output is activated, the CO

2

output will automatically be turned off to prevent wasteful venting of CO2.

Nighttime Control:

During the Nighttime, the Hyperion® 2 uses the Nighttime control setpoints
to keep its environment at the desired levels. During Nighttime mode, the
LED on the remote sensor will be off but quickly flash every three seconds,
and the Hyperion® 2 remote controller will show the night symbol for MODE
in the upper right-hand corner.

Controlling Relative Humidity (RH):

The Hyperion® 2 maintains its environment’s RH as described in the
Daytime Control section; however, it will use a separate Nighttime
setpoint. This allows the user to tightly control the RH to provide an
ideal growing environment.

Controlling Temperature:

The Hyperion® 2 maintains its environment’s temperature as described
in the Daytime Control section; however, it will use a separate
Nighttime setpoint. This allows the user to accurately control the
temperature to provide an ideal growing environment during day and
night conditions.

Controlling CO2:

During Nighttime, the CO2 output is never active: the environment’s
CO2 levels are controlled by ventilation (instead of enrichment). If the
CO2 levels climb above the Nighttime setpoint, the Exhaust output will
activate to lower CO

2

levels below Nighttime CO2 setpoint.

Lighting Control:

The Hyperion® 2 lighting controller is specifically designed for operation
of an indoor garden lighting system. The controller will operate your lights
for any sequence over a 24-hour period. The controller can handle up to
a maximum of four (4) 1000 watt HID metal halide, high pressure sodium
(HPS), ceramic (LEC) or LED grow lights. The Hyperion® 2 lighting controller
provides up to 20 amps of capacity on a standard 240 Volt circuit.

9

Light Odometer Feature (Change Bulbs Icon):

The Hyperion® 2 monitors the total time the lights output has been enabled.
After 4,000 hours the remote controller will show the change bulbs icon.
This is used to indicate that the grow lights may be approaching the end of
their useful life.

Alternate Exhaust Daytime/Nighttime Control:

The Hyperion® 2 has an Alternate Exhaust mode: this mode changes how
the Hyperion® 2 controls humidity inside the room. While the Hyperion® 2 is
in the Alternate Exhaust mode, the Dehumidification output is deactivated
completely. Details on how to enable/disable this feature are given in
Alternate Exhaust Mode in the Checking and Adjusting the Hyperion® 2
Settings section of this document.

Controlling RH with Alternate Exhaust Feature Enabled:

If the room’s RH rises above the RH setpoint by the amount of the
hysteresis setting (or the setpoint plus 2%), the Exhaust output will activate.
This output will remain on until the room’s RH drops below the setpoint
by the hysteresis setting (the setpoint minus 2%). There is still a separate
Daytime and Nighttime setpoint.

The Exhaust output is also activated by the temperature and CO2 Nighttime
settings as described in Normal Daytime/Nighttime Control.

NOTE: The CO2 output is always defeated when the Exhaust output
is activated.

10

Checking and Adjusting the Hyperion® 2 Settings

Checking the Hyperion® 2 Control Parameters:

1. Press and hold the Menu button
until the first parameter (LIGHTS)
begins to blink.

2. Use the Menu button to cycle
through each of the parameters.
The current setting for each
parameter will be displayed
as the setting is selected. The
settings available are:

a. LIGHTS

b. TIME

c. DAY TEMP

d. NIGHT TEMP

e. DAY CO2

f. NIGHT CO2
g. DAY RH
h. NIGHT RH

i. ALTERNATE EXHAUST

MODE ENABLE/DISABLE

NOTE: After 5 seconds with no buttons pressed the display will stop
blinking and the system will return to normal function.

Light Timing Adjustment:

To avoid making any changes, allow 5 seconds with no buttons pressed at
any time during this procedure: the display will stop blinking and the system
will return to normal operation.

1. Follow steps in the ‘Checking The Hyperion® 2 Control Parameters’
and select LIGHTS. Press the Select button and ON PERIOD will begin
to blink.

2. Use the Up and Down buttons to cycle through and select the
desired on period then press the Select button. Refer to Table 1 for a
description of the ON PERIOD settings.

NOTE:
*If ON or OFF is selected for the ON PERIOD the display will go blank

before returning to normal operation and the lights will be set to the

chosen state indefinitely.
*If Custom is selected for the ON PERIOD proceed to step 3.
*If either 12 HRS or 18 HRS is selected for the ON PERIOD skip to step 4.

Figure 3: Remote Controller

LIGHTS: ONOFF

STATUS

MODE

NightDay

ON PERIOD: 12 hrs. 18 hrs.

Custom

CODE
NETWORK

Low Battery

88

88:88
888

8880

88

AM
PM

PPM

%

ºF
ºC

hrs.

88

Menu Up Down Select

11

Table 1: On Period Settings for Hyperion® 2 Lighting Control

ON PERIOD Description

12 hrs. Flowering: lights stay on for 12 hours in a 24-hour

period.

18 hrs. Vegetative: lights stay on for 18 hours in a 24-hour

period.

Custom Duration can be changed from 1 to 23 hours in a

24-hour period.

ON Lights will remain on indefinitely.

OFF Lights will remain off indefinitely.

3. Use the Up and Down buttons to adjust the desired custom ON PERIOD.
This setting can be adjusted from 1 to 23 hours in increments of 1 hour.
Press the Select button and the hours of the time will begin to blink.

4. Use the Up and Down buttons to adjust the hour of the scheduled time
for the lights to be activated. Note that adjustments to the hours will
also change the AM/PM icons. Press the Select button and the minute
portion of the time begins to blink.

5. Use the Up and Down buttons to adjust the minutes of the scheduled
time for lights to be activated. Press the Select button and the screen
will go blank. The lighting schedule is now saved and the display will
resume normal operation. No changes are saved until this step has
been completed.

Resetting the Light Odometer (Change bulbs Icon):

The Hyperion® 2 monitors the total time the lights output has been enabled.
After 4,000 hours the remote controller will show the Change bulbs icon.
This is used to indicate that the light bulbs may be approaching the end of
their useful life.

To check the current amount of time logged on the light odometer, follow
these steps:

1. Press the Menu button until the LIGHTS setting begins to blink.

2. Press and hold the Up and Down buttons for 3 seconds: the display
will go blank.

3. Release the Up and Down buttons: the display will show the
current number of hours of the Light Odometer where the time is
normally displayed.

4. After 5 seconds with no buttons pressed, the display will go back to
showing the room’s current readings.

12

To Reset the Light Odometer and Clear the Change Bulbs Icon:

1. Follows steps 1 through 3 (on page 11) to display the current number
of hours logged on the light odometer.

2. Press and hold the Select button for 5 seconds while the display is
showing the current odometer reading. The displayed reading will be
reset to 0 and the Change bulbs icon will be cleared.

NOTE:

*It’s recommended you reset the light Odometer every time you replace

your lamps.

*The remote controller will not show the current time if the Low Battery icon

is displayed: this will also prevent the Hyperion® 2 from running the lighting
schedule. Refer to the SETTING THE CURRENT TIME section below for
instruction on how to replace the battery and reset the remote controller’s
time.

Setting the Current Time:

To avoid making any changes, allow 5 seconds with no buttons pressed at
any time during this procedure: the display will stop blinking and the system
will return to normal operation.

1. Follow the steps in the ‘Checking The Hyperion® 2 Control Parameters’
section and select TIME.

2. Press the Select button and the hours will begin to flash.

3. Use the Up and Down buttons to adjust the hours to the correct value.
The AM/PM icons will change with adjustments to the hours. When the
correct hour has been selected, press the Select button and minutes
will begin to flash.

4. Use the Up and Down buttons to adjust the minutes to the correct
value. Press the Select button and the display will go blank
momentarily to indicate the time adjustment has been completed.

13

Battery Replacement:

The remote controller uses a standard BR2325 lithium coin cell battery to
keep time while it is unplugged: this battery typically last 10+ years before
replacement is necessary. When the battery’s charge had been depleted,
the Low Battery icon will appear on the display and the time will show
dashes. To replace the battery follow these steps:

1. Unplug the remote controller and open the enclosure to access the
battery. The battery will be visible on the back of the circuit board.

DO NOT CHANGE THE BATTERY WHILE THE REMOTE
CONTROLLER IS CONNECTED TO POWER!

2. Carefully remove the battery and insert a new BR2325 battery in the
correct orientation: the positive side (+) of the battery should be facing up.

3. Reassemble the enclosure and plug in the remote controller. The time
will continue to display dashes and the Low Battery icon until the time
has been reset.

4. Set the correct time by following ‘Setting the Current Time’ instructions
listed above. Once the time has been set the Low Battery icon will be
cleared. Note that the lighting schedule will not run until the time has
been set and the Low Battery icon has been cleared.

Temperature Setting:

To avoid making any changes, allow 5 seconds with no buttons pressed at
any time during this procedure: the display will stop blinking and the system
will return to normal operation.

1. Follow the steps in the Checking The Hyperion® 2 Control Parameters
section and select either the Daytime or Nighttime TEMP parameter.

2. Press the Select button and the temperature units will begin to flash.

3. Press the Up or Down button to toggle between° F and° C. When the
desired unit is selected, press the Select button and the temperature
setting will blink.

4. Use the Up and Down buttons to adjust the setpoint to the
desired temperature.

5. Press the Select button and the screen will go blank. The temperature
setting is now saved and the display will resume normal operation. No
changes are stored until this step is complete.

14

CO2 and RH Settings:

To avoid making any changes, allow 5 seconds with no buttons pressed at
any time during this procedure: the display will stop blinking and the system
will return to normal operation.

1. Follow steps in the Checking The Hyperion® 2 Control Parameters
section and select Daytime or Nighttime setting of either the CO2 or RH
parameter.

2. Press the Select button and the current setting will begin to blink.

3. Use the Up and Down buttons to adjust the setpoint to the desired level.

4. Press the Select button and the screen will go blank. The setting has
now been saved and the display will resume normal operation. No
changes are stored until this step has been completed.

Alternate Exhaust Mode:

It is possible to change how the Hyperion® 2 controls the dehumidification
of a room by enabling the Alternate Exhaust mode. Please refer to Alternate
Exhaust Daytime/Nighttime Control in the Control Description section of
this document for more information.

To enable/disable this feature follow the steps below:

1. Enter the adjustment menu on the remote controller by pressing and
holding the Menu button until the LIGHTS setting begins to flash.

2. Cycle through the settings by pressing the Menu button until both
TEMP and RH begin flashing. A number (1 or 2) will also be flashing:
this number indicates the current mode.

3. To change from normal mode to alternate exhaust mode while TEMP &
RH are flashing: Press Select, then press Down button to display “2”.
Now the Hyperion® 2 is in Alternate Exhaust mode. To change back to
Normal mode press select, then press Up button to display “1”. Now
the Hyperion® 2 is in Normal Exhaust mode.

Restoring Factory Default Settings:

To restore all factory default settings (shown in the Factory Defaults and
Control Limits section of this document), press and hold both the Menu
and Select buttons simultaneously for 5 seconds. The display will go blank,
the controller will reset and all the factory default settings will be restored.

1= Normal Mode

(separate designated outputs used to

control temperature and RH).

2 = Alternate Exhaust Mode

(both temperature and RH are

controlled with the Exhaust output).

15

Codes and Errors

Each of the conditions or errors described below has a code that is shown
on the remote controller and can be used to identify the condition. Table
2, located on page 18, is a complete list of the codes reported by the
Hyperion® 2’s remote controller.

The Hyperion® 2’s remote sensor is equipped with the tricolor LED that can
also be used to determine the Hyperion® 2’s current status: a description of
the LED’s behavior is given in Table 3, located on page 19.

Over Temperature Shutoff:

The Hyperion® 2 constantly monitors the room’s temperature. If the room’s
temperature climbs to 95° F and the Hyperion® 2 has the Light output
active, it will enable the Over Temperature feature.

The Over Temperature feature will automatically turn off the Lights output
and activate the Exhaust output. The Lights output will remain off for a
minimum of 15 minutes. The display will show CODE 1 while this feature is
active and the remote sensor’s LED will rapidly flash green or yellow (see
Table 3, page 19 for more information). Once 15 minutes has passed, and
if the temperature has dropped to 86° F or less (Exhaust output will remain
on until the temperature setpoint has been reached), the Lights output
will turn on and the controller will resume normal operation. The actual on
time of the lights will be shortened slightly by this feature because time
will continue to be kept while this is in effect: the overall lighting “on” time
duration always remains the same.

If the Over Temperature feature was activated, the Hyperion® 2 will display
CODE 10 (see Table 2, page 18) after the lighting schedule is completed.
Refer to the Lighting Schedule Interrupted Condition section for more
information.

High Temperature Condition:

The High Temperature warning is shown if the room’s temperature climbs
to 95° F and remains there for 30 minutes while the Light output is off. The
remote controller will show CODE 2 to indicate this condition has occurred.
This condition will automatically be cleared when the room’s temperature
drops below 86° F. The Exhaust output is enabled and will remain on until
the temperature as dropped to the desired setpoint.

Low Temperature Condition:

The Low Temperature warning is enabled when the room’s temperature
drops below 45° F and remains there for 30 minutes. The remote controller
will show CODE 3 until the temperature rises above 45° F.

16

High Humidity Condition:

The Hyperion® 2 displays a High Humidity warning by showing CODE 4:
this occurs when the room’s RH rises above 80% and remains there for 30
minutes. This condition is automatically cleared when the RH drops below
80%.

Low Humidity Condition:

The Hyperion® 2 displays a Low Humidity warning by showing CODE 5:
this occurs when the room’s RH drops below 30% and remains there for 30
minutes. This condition is automatically cleared when the RH rises above 30%.

High CO2 Concentration Condition:

If the CO2 levels of the room rise above 5000 ppm, the Hyperion® 2 will display
CODE 6. This condition is cleared when the CO2 levels drop below 5000 ppm.

Empty CO2 Tank Condition:

This feature informs the user when the CO2 tank used to enrich the room
is empty. During the Daytime, if the CO2 level is below the desired setpoint
(minus hysteresis) for 30 minutes or more, the Hyperion® 2 will display
CODE 7. This condition is cleared when the CO2 levels rise to the desired
setpoint.

No Measured Light Condition:

When the Hyperion® 2 is set to have the Lights output active, the remote
sensor should detect light and begin using the Daytime control parameters.
If the light output has been active for 15 minutes and the remote sensor
does not measure light, it will display CODE 8 in the lower right-hand
corner of the screen. This is a useful feature that can inform the user that
there may be something wrong with the lights or that the remote sensor
is not placed properly. This code is automatically cleared when the photo
sensor detects light during daylight period.

No Measured Darkness Condition:

When the Hyperion® 2 is set to have the Lights output off, the remote
sensor should NOT detect light and use the Nighttime control parameters.
If the light output has been off for at least 15 minutes and the remote
sensor measures light, it will display CODE 9 in the lower right-hand
corner of the screen. This is a useful feature that can inform the user that
unwanted light is present inside the room. This code is automatically
cleared when no light is detected.

17

Lighting Schedule Interrupted Condition:

If the Hyperion® 2 has been set to run a lighting schedule and the schedule
was interrupted for any reason (including a power failure), the remote
controller will show a CODE 10. This indicates that the lights were not on
for the entire scheduled time. The condition will automatically be cleared
when the next lighting schedule begins; this condition is also cleared if a
new lighting schedule is set.

Temperature Sensor Error:

If the Hyperion® 2’s remote sensor is unable to get readings from its
temperature sensor it will turn off all load outputs. The remote sensor’s
LED will flash red twice periodically and the remote controller will show
CODE 20. If the problem is resolved, the controller will return to normal
functionality.

RH Sensor Errors:

If the Hyperion® 2’s remote sensor is unable to get readings from its RH
sensor it will turn off all load outputs. The remote sensor’s LED will flash

red once periodically and the remote controller will show CODE 21. If the

problem is resolved, the controller will return to normal functionality.
If the RH detector of the Hyperion® 2’s remote sensor becomes saturated
with water, accurate readings are not possible. If this happens, all
load outputs will be disabled. The remote sensor’s LED will flash once
periodically and the remote controller will show CODE 22. Once the
remote sensor has dried out and accurate readings are possible, this
error condition will automatically be cleared and the controller will return to
normal functionality.

CO2 Sensor Error:

If the Hyperion® 2 is unable to get CO2 readings from the CO2 sensor, it will
turn off all load outputs. The remote sensors LED will flash red three times
periodically and the remote controller will show CODE 23. If the problem is
resolved, the controller will return to normal functionality.

Real Time Clock Error:

If the Hyperion® 2’s remote sensor is unable to communicate with the on­board real time clock (RTC), the load outputs will be disabled. The remote
sensor’s LED will flash red four times periodically and the remote controller
will show CODE 24. If the issue is resolved, the controller will resume
normal operation.

18

Table 2: Remote Control Remote Control Codes

Code # Code Type Description

Code 1 Over Temperature Temperature is greater than or equal to 95° F while

the Lights Output is enabled.

Code 2 High Temperature Temperature is greater than or equal to 95° F for

an excess of 30 minutes while the Lights output is
disabled.

Code 3 Low Temperature Temperature is less than or equal to 45° F for an

excess of 30 minutes.

Code 4 High Humidity Humidity above 80% for an excess of 30 minutes.

Code 5 Low Humidity Humidity below 30% for an excess of 30 minutes.

Code 6 High CO

2

CO2 is greater than or equal to 5000 ppm.

Code 7 Empty CO2 Tank Injecting CO2 for an excess of 30 minutes and CO2

levels have not reached setpoint (daytime mode
only).

Code 8 No Measured Light Light output has been enabled for a minimum of 15

minutes and no light is detected.

Code 9 No Measured Darkness Light output has been disabled for a minimum of 15

minutes and light is detected.

Code 10 Power Interrupted Unable to complete lighting schedule (power outage

likely).

Code 20 Temperature Sensor Error Sensor module is unable to get temperature reading

from temperature detector.

Code 21 RH Sensor Error Sensor module is unable to get RH reading from

detector.

Code 22 RH Sensor Saturated Sensor module has detected that RH detector is

saturated.

Code 23 CO2 Sensor Error Sensor module is unable to get CO2 readings from

CO2 detector.

Code 24 RTC Error Remote Control is unable to get time from the real

time clock.

Remote Sensor LED:

The tri-colored LED on the remote sensor is used to display the status
of the Hyperion® 2 by: color, flashes, and blinking frequency. In general,
a green LED indicates the controller is functioning normally. When the
LED is yellow, it indicates that there is a problem with the wireless
communication. A red LED is used to indicate an error with the controller
or one of its sensors. Refer to Table 3 for further details.

19

Table 3: Remote Sensor Module LED Codes

LED Code Meaning

Green: Solid on (no flashes).

(see CO2 Calibration section)

Calibration of CO2 sensor was
successful.

Green: Normally on, flashes off
twice.

Daytime mode and functioning
normally.

Green: Normally off with two green
flashes.

Nighttime mode and functioning
normally.

Green: Continuous blinking. High Temperature Shutoff feature is

active.

Yellow: Solid on (no flashes). Rebuilding Wireless Network: see

REBUILDING THE WIRELESS
NETWORK in the Hyperion® 2
Control Network section of this
document for more information.

Yellow: Normally on, flashes off
twice.

Daytime mode: unable to
communicate with Hyperion® 2
Remote Control.

Yellow: Normally off with two yellow
flashes.

Nighttime mode: unable to
communicate with Hyperion® 2
Remote Control.

Yellow: Continuous blinking. High Temperature Shutoff feature is

active: unable to communicate with
the Hyperion® 2 Remote Control.

Red: Solid on (no flashes).

(see CO2 Calibration section)

Unable to calibrate CO2 sensor.

Red: 1 flash. RH sensor not functioning.

Red: 2 flashes. Temperature sensor not function-

ing.

Red: 3 flashes. CO2 sensor not functioning.

Alternating: LED color changes
green, yellow, red.

CO2 sensor is being calibrated
(takes about 15 minutes).

20

Calibration

CO2 Calibration:

The Hyperion® 2 remote sensor is equipped with two buttons located on
the bottom of the unit. It normally requires calibration approximately
every 3 years. The button on the left (Figure 4) is used to place the
controller into CO2 Calibration mode: the Hyperion® 2’s CO2 sensor will
automatically calibrate to normal outside air CO2 concentration. To properly
calibrate the CO2 sensor, simply follow these steps:

1. Move the remote sensor to an outside area where CO2 pollution is at
a minimum: Do not attempt to calibrate the CO2 sensor indoors, while
breathing directly on the unit, next to a running vehicle, near animals, etc.

2. Power up the remote sensor: attach the remote sensor to the master
controller, then plug the master controller into a 120V AC power source.

3. Insert a small, non-metallic item, such as a toothpick, through the
CO2 calibration buttonhole (shown in Figure 4) and press the calibration
button for approximately three seconds. The LED will begin alternating

green, yellow, and red to indicate the CO2 sensor is being calibrated.

4. Allow time for the calibration sequence to complete; this usually takes
approximately 15 minutes. Upon completion, the LED will illuminate
solid green if the CO2 calibration was successful or solid red if it
was unable to calibrate properly. Upon completion of the calibration
sequence, the Hyperion® 2 will not resume controlling the room’s
environment until it has received acknowledgment of the calibration
results.

NOTE: Calibrating to outside air provides a good approximate
calibration. The accuracy of the calibration will be determined by the
quality of the air that the CO2 sensor is exposed to during this process.

Figure 4: Bottom View of Remote Sensor

21

Hyperion® 2 Wireless Control Network

The Hyperion® 2 is equipped with transceivers that operate in the non­licensed 2.4 GHz frequency band and are FCC (USA), IC (Canada),
and ETSI (Europe) compliant. The remote sensor and remote controller
communicate wirelessly and allow remote viewing of the controlled space’s
conditions. All control parameters are changed over the wireless network
via the remote controller.

Normal Operation:

Under normal conditions, the remote controller and remote sensor
communicate via this wireless control network. During normal operation the
remote sensor’s LED will illuminate green and behave as described in the
remote sensor LED section of this document.

Wireless Control Network Error:

Network codes on the remote controller and a yellow LED on the remote
sensor indicate problems with the wireless control network. All network
codes are described below in Table 4. The behavior of the remote sensor’s
LED is described in Table 3 of the Codes and Errors section of this
document.

Table 4: Remote Controller Network Messages

Network Code Type Description

Network 0 No Sensor

Module.

Remote Control is unable to
communicate with the sensor
module via wireless control network.

Network -1 No Wireless

Control Network.

Remote Control needs to be
paired with the sensor module.
Refer to REBUILDING THE
WIRELESS NETWORK in the
Hyperion® 2 Wireless Control
Network section of this document
for more information.

The Hyperion® 2 will control the room’s environment even if wireless
communication is interrupted; however, it will not be able to run the lighting
schedule unless the wireless control network is functioning properly.

22

Remote Controller Behavior:

If the remote controller is unable to communicate with the remote sensor
after the control network has already been formed, it will show dashes for
all readings and NETWORK 0 in the lower right-hand corner.

When wireless communication has been re-established and is functioning
properly, the network code will be cleared and the display will function
normally.

Remote Sensor Behavior:

On power-up the remote sensor will search for the remote controller via
wireless network; during this time the LED will illuminate yellow. The
behavior of the LED will indicate its current function as described in Table 3
of the Codes and Errors section of this document.

When wireless communication has been re-established and is functioning
properly, the LED will illuminate green and behave as described in Table 3
of the Codes and Errors section of this document.

Range Testing:

Under ideal conditions (i.e. line of sight, no metallic interference, low
humidity, etc), the Hyperion® 2 is capable of communication up to 150+
feet. Environmental changes and obstacles (particularly ones made of
metal) will reduce maximum communication range. To test the signal
strength between the modules, follow these steps:

1. Power-up both the sensor and remote controllers.

2. Press and hold the Select button of the remote controller until the
screen goes blank and only the NETWORK icon and a number begin
to blink in the lower right-hand corner of the display. The number
shown indicates the signal strength between the two modules and is
described below:

3. After 10 seconds with no buttons pressed, the remote controller will
return to showing the current room’s environment.

-1 Remote controller is attempting to rebuild network (refer to
Rebuilding The Wireless Network section on the next page): no
signal strength information is available.

0 Very low signal strength or no signal detected.

1 Good to moderate signal strength.

2 Strong signal strength.

23

Rebuilding The Wireless Network:

Under normal circumstances it will not be necessary to rebuild the wireless
network as it is preset at the factory. However, if necessary, the wireless
network can be rebuilt by follow these steps:

1. Press and hold the Network button on the remote sensor (refer to

Figure 4) until the LED illuminates solid yellow (Table 3): this will place
the remote sensor into a searching mode. While in this mode the
Hyperion® 2 will disable all outputs and will not attempt to control.

2. Bring the remote controller in close proximity to the remote sensor to be
sure that they are within communication range.

3. Press and hold the Up and Menu buttons on the remote controller
simultaneously until the display begins to blink NETWORK -1.

4. Press the Select button and the remote controller will begin searching
for the remote sensor. The remote controller will reset and begin to
function normally. If the Select button is not pressed within 5 seconds,
the remote controller will exit this mode return to normal operation.

Installation Diagram

Controller

20 AMP

LIGHTING

CIRCUIT

BREAKER

15 AMP

ENVIRONMENT

CIRCUIT

BREAKER

240 VOLT
POWER
OUTPUT
5 AMPS Per
Receptacle

CO

2

OUTPUT

120V

1.5 AMPS

EXHAUST

OUTPUT

120V

2.0 AMPS

DEHUMIDIFY

OUTPUT

120V

7.5 AMPS

240 VOLT
POWER
OUTPUT
5 AMPS Per
Receptacle

40 Amp / 240V AC / 60Hz

Single Phase Input

150 feet

240V AC Ballasts

240V AC Ballasts

Garden

or

or

Hyperion

Remote Controller

CO Generator

CO



Tank

Exhaust Fan

Dehumidier

Fan

24

Factory Defaults and Control Limits

Temperature:

Default Unit of Measurement:° F
Default Daytime Setpoint: 75° F (24° C)
Default Nighttime Setpoint: 65° F (18° C)
Default Hysteresis: ± 3° F (or 6° F centered)
Measurement Range: 32° F (0° C) to 120° F (49° C)
Setpoint Range: 45° F (7° C) to 85° F (29° C)

Humidity:

Default Daytime Setpoint: 55%
Default Nighttime Setpoint: 50%
Default Hysteresis: ± 2% (or 4% centered)
Measurement Range: 5% to 95%
Setpoint Range 20% to 90%

CO2:

Default Daytime Setpoint: 1000 ppm
Default Nighttime Setpoint: 600 ppm
Default Hysteresis: - 100 ppm (or 100 ppm below setpoint)
Measurement Range: 0 ppm – 5100 ppm
Setpoint Range: 500 ppm – 2500 ppm

Warranty Information

• Titan Controls® warrants the original purchase of this product against
defects in material and workmanship under normal use for three (3) years
from the date of purchase.

• During the warranty period, Titan Controls® will, at our option, and
without charge, repair or replace this product if the controller or any of its
components fail or malfunction.

• All returns or repairs must be accompanied by a Return Merchandise
Authorization (RMA) number prior to any service of the product.

• This warranty is expressly in lieu of all other warranties, expressed or
implied, including the warranties of merchantability and fitness for use
and of all other obligations or liabilities on the part of the seller.

• This warranty shall not apply to this product or any part thereof
which had been damaged by accident, abuse, misuse, modification,
negligence, alteration or misapplication.

• Controllers with serial numbers or date tags that have been removed,
altered or obliterated; broken seals or that show evidence of tampering;
mismatched serial numbers or nonconforming parts, are excluded
from coverage.

25

• Titan Controls® makes no warranty whatsoever in respect to accessories
or parts not supplied by Titan Controls®.

• Monetary refunds of the warranty will not be given.

• The Buyer assumes all responsibility regarding the use & installation of
this controller.

• All warranty service is provided through the factory or an authorized
service representative.

• This warranty shall apply only to the United States, including Alaska,
Hawaii and territories of the United States and Canada.

• Defective controllers need to be returned with the “proof of
purchase/receipt”.

• For additional warranty information, contact a Titan Controls® Technical
Service Representative (888-808-4826) or your Dealer. Our normal
business hours are Monday – Friday, 8 a.m. to 5 p.m. Pacific Standard
Time. We are closed most major holidays.

• NOTE: Titan Controls® is a manufacturer of environmental controls. All
sales offerings to the public are done through a nationwide group of
Dealers. No sales offerings will be made directly to the general public.

• FOR WARRANTY SERVICE: Please read warranty information first.

• If after reviewing the troubleshooting tips the unit will still not work, you
should return it to the Dealer where you purchased the controller. They
will be able to further evaluate the unit and test its various components
and quite possibly will be able to identify and/or fix any problems. If the
Dealer is unable to fix the unit, they will return it to us for factory repair.

• If there are no Dealers in your area, you may contact us directly for
technical support. If we cannot help you resolve the problem over the
phone, we will issue you a RMA # (return merchandise authorization)
authorizing you to return the unit to us for factory reconditioning (if
the unit is under warranty). Contact the number below for a RMA and
shipping address. Complete the form below and include it with your unit.
Also please write the RMA # on the outside of the box.

• Please package the unit in its original packaging. If it is damaged during
shipping we cannot be responsible.

• Once we receive the unit back, we will repair the controller within 48 hours
(business) and return it to you freight prepaid via UPS ground shipment.

26

Troubleshooting Tips

If the Hyperion® 2 is not performing as expected, try the following:

• Confirm that your power input is active from your breaker panel and
providing 240 Volts / 40 Amps / 60Hz to the controller.

• Check the voltage input of your incoming cord set using a voltage test
meter to verify power is flowing to the controller.

• Make sure all of your connections are tight. Loose connections can
cause “arcing”. Retighten every 90 days.

• Then confirm that power is active and proper at your 240V AC & 120V
AC outlets using a voltage test meter.

• Verify that your power cords and ballasts are functioning properly and
that there are no shorts or arcing occurring.

• Should you find your circuit breaker keeps tripping, check your
breakers and equipment to verify that they are the right amperage for
your application.

• If you turn ‘OFF” the power switch and your lights remain on, contact
us immediately for resolution.

• Still having problems with your Hyperion® 2? Please contact our
Technical Service Representative at 888-808-4826 to assist you further.

Controller Specifications:

Size 14” H x 17” W x 4” D

Weight 9.5 lbs.

Maximum Amperage 40 Amps

Voltage Input 240V AC

Voltage Output 240V AC for lighting outputs

Maximum Lighting
Amperage

20 amps (1000 watts per outlet)

Voltage Output 120V AC for dehumidifier, CO2 and

fan outputs

Maximum Environmental
Control Amperage

15 Amps

Hertz 60Hz

Storage Temperature 32° F (0° C) to 135° F (57° C)

Operating Temperature 40° F (4° C) to 125° F (52° C)

27

FOR WARRANTY SERVICE: Please read warranty information first.

If after reviewing the troubleshooting tips the unit will still not work, you should
return it to the Dealer where you purchased the controller. They will be able to
further evaluate the unit and test its various components and quite possibly will be
able to identify and/or x any problems. If the Dealer is unable to x the unit, they
will return it to us for factory repair.

If there are no Dealers in your area, you may contact us directly for technical
support. If we cannot help you resolve the problem over the phone, we will issue
you a RMA # (return merchandise authorization) authorizing you to return the unit
to us for factory reconditioning (if the unit is under warranty). Contact the number
below for a RMA and shipping address. Complete the form below and include it
with your unit. Also please write the RMA # on the outside of the box.

Please package the unit in its original packaging. If it is damaged in shipment we
cannot be responsible.

Once we receive the unit back, we will repair the controller within 48 hours
(business) and return it to you freight prepaid via UPS ground shipment.

Include the following if returning directly to Titan Controls

®

• Proof of purchase • This completed form • RMA # on the outside of the box

Return Merchandise Authorization Number (Required)_____________________________________________

Company Name: ____________________________________________________________________________________

Contact Name: _____________________________________________________________________________________

Address: __________________________________________________________________________________________

____________________________________________________________________________________________________

Phone #: ___________________________________________________________________________________________

Email address: _______________________________________________________________________________

What is the nature of the problem? ____________________________________________________________

_____________________________________________________________________________________________

_____________________________________________________________________________________________

_____________________________________________________________________________________________

_____________________________________________________________________________________________

_____________________________________________________________________________________________

_____________________________________________________________________________________________

Send to your nearest location – shipping address will be given when the RMA # is issued:

www.titancontrols.net

For technical assistance call us at 1-888-80-Titan or 1-888-808-4826.

1 Square = ____ Foot/Feet

VANCOUVER, WASHINGTON U.S.A.

Revised 06/29/2017AW #111810 © Titan Controls

®