
Original Instructions_DFT_TTB583PMP(XKS-400PW)_V1_131114
TTB583PMP
Barcode: 01031799
Ref. No.: 65041

Submersible Pump TTB583PMP

This product can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use of
the product in a safe way and understand
the hazards involved.
Children should be supervised to ensure
that they do not play with the product.
Cleaning and user maintenance shall not be
made by children without supervision.
If the power cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in order
to avoid a safety hazard.
This product is to be supplied through a
residual current device (RCD) having a rated
residual operating current not exceeding 30
mA.
Prevent access of children with appropriate
measures.
Do not use when people are in the water.
Do not operate the pump without water.
Make sure that no marine animals (e.g. fish)
are extracted by the product.
Have in mind that pollution of the liquid could
occur due to leakage of lubricants.
Protect the electrical connections and cords
from heat, oil, sharp edges and moisture.
Protect the product from frost and running
dry.
Avoid circulation of aggressive fluids of
abrasive materials.
Do not use the power cord or the float switch
cable to transport or secure the product. Fix
a rope to the handle for submerging, lifting or
securing
Check and clean the outlet and the inlet of
the pump when needed.
Do not pump liquids with sand or other
abrasive substances. It causes increased
wear and reduces the pumps output.
The product is designed for clear water with
a diameter of suspended impurities not
exceeded 30mm.
The product should be used for pumping
water temperature below 35°C, do not use
the product for other liquids (hydrocarbons,
oils, corrosive liquids, flammable liquids…).
Never use the product in case of danger of
frost.
The product is not designed for continuous
Pump safety warnings

use. Please rest it for 10 min after each 1
hour running.
Familiarise yourself with the operation,
adjustments and functions. Internalise and
follow the safety and operation instructions
in order to avoid possible risks and hazards.
Contact a qualified person or your dealer if
you have questions after reading the
instruction manual.
Store the instruction manual so that it is
accessible for all users. Also relay it when
giving the product to others.
Do not attempt to modify the product in any
way. Only use attachments and accessories
recommended by the manufacturer.
Use the product only in accordance with this
instruction manual. Misuse and incorrect
handling will lead to hazards for people and
property.
Do not use the product if damage is visible.
Check the power cord, plug, attached hoses
and casing before each use. Faulty products
must be repaired or proper disposed of.
Disconnect the product from the power
supply immediately if the cord or the product
supply immediately if the cord or the product
is damaged or if a breakdown occurs.
Have the product repaired only by a qualified
specialist. Improper repairs can lead to
electric shocks or other accidents.
Pull the plug rather than the power cord to
disconnect the product from the power
supply.
Do not let the power cord hang over edges,
do not squeeze or bend it.
Use extensions cords that correspond with
the technical requirements of this product if
using an extension cord in unavoidable.
When operating products outdoors, use an
extension cord suitable for outdoor use.
General safety warnings

9000
6
6
yyWxx
Manufacturing date code:Year of manufacturing (20yy) and week
of manufacturing (Wxx)

400 W
9000 l/h
max. 6 m
max. 6 m
approx. 5.1 kg
Ø 25 mm (outter thread) for connector
Ø 32 mm (outter thread) for adaptor

upper
Fasten a rope (not
provided) to the handle (1)
and submerge the product
carefully into the water
reservoir (Fig.4)
Lift the pump by a rope(not
provided) from the water
reservoir after use.
WARNING: Do not lift the pump by power cord.

TTB583PMP
400
6
NOTE: Make sure the cable length is not less than 45mm between
float switch and clip.
10

NOTE: This product can be used to suck up water with a lower height
(70mm: depending on the pump) but must be manually operated the
float.

Ø32mm (outter thread) and
Ø32mm (outter thread) for Adaptor
Ø32mm (inner thread) and
Ø25mm (outter thread) for Connector

Submersible Pump TTB583PMP
Date: 20/11/2013
Submersible Pump TTB583PMP