Titan TED-1 Instruction Manual
4
ASSEMBLY DIAGRAM
INSTRUCTION MANUAL
Titan CTS
www.titancts.com
3040 White Horse Road | Greenville, SC 29611 | 864.385.7030
TED-1 Pump
NO
1
2
3
4
5
6
7
8
9
10
10-1
10-2
10-3
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
RAW MAT`L
PP
PP
POM
PP
STAINLESS STEEL(SUS 304)
M4x10
Φ3, RED
CEM
10kΩ
5A
VITON
POM
NBR
PP
STAINLESS STEEL(SUS 304)
VITON
PE
PE
POM
VITON
VITON
POM
ZDC
POM
STAINLESS STEEL(SUS 304)
POM
VITON
PP
PP
STAINLESS STEEL(SUS 304)
PE
PP
PP
STAINLESS STEEL(SUS 304)
POM
VITON
VITON
PP
STAINLESS STEEL(SUS 304)
VITON
PP
Q`TY
1
1
1
1
1
6
1
1
1
1
1
2
1
2
2
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
3
2
3
2
1
1
1
1
1
1
1
1
1
1
1
FRONT COVER
BACK COVER
NOZZLE HOLDER
HOLDER COVER
NOZZLE HOOK
SCREW
TOGGLE SWITCH
WATERPROOF CAP
LED LAMP
PCB ASS`Y
RESISTOR
FUSE HOLDER
FUSE
CONNECTOR WIRE
CONNECTER PIN
MOTOR WIRE PACKING
BODY
O-RING(BODY)
DRUM BUNG ADPTER
INNER PIPE
SUCTION PIPE PACKING
SUCTION PIPE
MOTOR WIRE
MOTOR COVER
O-RING(MOTOR COVER, HANDLE)
MOTOR
MOTOR PACKING
MOTOR CASE
IMPELLER
IMPELLER CASING
FILTER
END CAP
O-RING
(HOSE ADAPTER, SPOUT ADAPTER)
HOSE ADAPTER
JOINT NUT
HOSE CLAMP
DISCHARGE HOSE
HANDLE
NOZZLE CAP
NOZZLE SPRING
NOZZLE PISTON
O-RING(PISTON L)
O-RING(PISTON S)
NOZZLE LEVER
SPOUT
O-RING(SPOUT)
SPOUT ADAPTER
PART NAME
Precautions for Use
Names of Parts
Specications
Directions for Use
DANGER CAUTION
CAUTIONDANGER WARNING
5A
Operating temperature
Operating voltage DC12V ~ 20V
Approx. 5 Gallons
Approx. 10 ft
Delivery volume
Suction pipe length
Discharge hose length
Applicable liquids
Fuse
+5˚C ~ 40˚C (41˚F ~ 104˚F)
Diesel, DEF(AdBlue), Water, Kerosene, Antifreeze, Windshield washer uid,
Mild detergents, Agricultural chemicals, Light oils.
Toggle Switch
Nozzle holder
Nozzle
Drum bung adapter
Suction pipe
Discharge hose
Operating lamp(LED)
Follow all directions below to prevent
serious injury.
Do not use for ammable liquids or
concentrated acids.
Be cautious. This pump does not
have an explosion proof motor.
Do not use near the ammable
materials such as gasoline, gas, etc.
Only use on applicable liquids
written on the specications.
These instructions are to ensure the product is used correctly, safely, and to prevent any possible risk or damage to the user
and/or others people. Our company shall not take any responsibility for any failure of product, malfunction and damages
caused by improper use by the user or third parties.
Make sure the pump is tightly
secured to the drum(tank) before
turning the pump on.
Do not refuel directly while the
vehicle or equipment is turned on.
Do not leave the pump unattended.
Do not bend, bind or pull the power
cord by force.
Make sure to use the pump on even
surface.
Do not allow children to operate the
product without adult supervision.
After using the pump, do not keep it
on its side or upside down.
Make sure to remove any left-over
liquid in the discharge hose after
each use.
Do not alter or disassemble the
pump.
Do not run the pump ‘dry’ or let the
pump idle without transferring.
Make sure to turn o the power after
using the pump.
Do not shock the pump.
Do not use deteriorated or
contaminated liquids and fuels.
Do not place the pump in a wet area.
Do not use this pump for hot liquids
above 40°C (104°F ).
WARNING
2 3
3
6
4
2
5
8
11
1
7
10
Insert the suction pipe into the
drum .
Tighten the drum bung adapter. Pull out the nozzle from the
nozzle holder.
Place the nozzle into the receiving
container to transfer liquid.
Toggle switch ON(Up). Pull the nozzle lever and start
supplying the liquid.
Release the lever when the liquid
supply is completed.
Toggle switch OFF(Down). Pulling the lever of the nozzle,
lift it up.
Let the left-over liquid in the hose
ow back into the drum (tank).
Insert the nozzle in the nozzle holder
for storage.
Approx. 850 ~ 33.5”~ 34”
9
Follow all directions below to prevent
serious injury.
Follow all directions below to prevent
serious injury.
Loading...