Titan 4 in 1 Battery Charger User Manual

Page 1
4 in 1 Battery Charger
MANUAL
4 in 1 Battery Charger
User Manual
1
2
3
4
5
6
7
(A) Step of Usage
Step 1. Please confirm that your electrical supply voltage comply with charger’s input voltage
Step 2. After plug in AC cord, press down key “ Battery Voltage Selection “ and select the battery voltage you need
a. When one LED indicator light comes on, it indicates that the charger is charging at 12 volts.
b. When two LED indicator light comes on, it indicates that the charger is charging at 24 volts.
c. When three LED indicator light comes on, it indicates that the charger is charging at 36 volts.
d. When four LED indicator light comes on, it indicates that the charger is charging at 48 volts.
Step 3. After completing step two, then the red wire connects to the positive while the black wire
connects to the negative.
Step 4. The LED display’s indicator lights will all come on with a indicator beep. Afterward the DC
battery will detect available battery power with the corresponding LED battery indicator, then the
battery charging process will begin.
. User’s Guide for 4 in1 Battery Charger
. Appearance of Structure
1. AC Input Cord
2. LED Display Panel
3. Battery Voltage Selection
4. Status Display
5. DC Output Cord
6. AC Fuse
7. Battery
Page 2
4 in 1 Battery Charger
MANUAL
Flash 4
times
It means that internal inside thermal
sensor is short or open circuit.
Please contact your local distributor
if the internal thermal sensor is abnormal,
Over temperature protection.
The charger will automatically restart when internal
temperature reaches operational temperature range.
Flash 5
times
Description Solution
Indicator
Light
Red
Light
It means that the charger isn’t correctly connected to battery
or the DC fuse is burned.
Flash 2
times
Please contact your local distributor
if the red indicator light still flashes twice
after disconnecting the cord.
Charger output voltage is not
compatible with the battery.
Please check that the correct
charging voltage is selected.
Flash 3
times
(C) Explanation of Usage
1. When it is charging , it does not effect your configuration if you press the voltage selecting
key. Please disconnect the battery if you wish to select a different voltage.
2. When float green light is flashing , it means that the battery is full.
3. Please disconnect the AC cord and DC output cord if you wish to end charging.
(b) Unusual Indicating light of charger instructed as below
(B) Status display light of charger instructed as below (a) Usual Indicating light of charger instructed as below
It is in floating status , battery is full.
It is in floating status, battery is full with floating current of < 0.5 A.
It is in Absorption C.V. (Constant Voltage) charging status.
Slow Flashing frequency
Yellow
Light
Fast Flashing frequency
Green
Light
Indicator light
Super Fast Flashing frequency
Slow Flashing frequency
Fast Flashing frequency
Descreption
It is in Soft Start status, current is charging slowly.
Lighting Up
It is in Absorption C.C.(Constant Current) charging status.
It is in Float C.C.( Constant Current ) charging status
and will become floating status.
Page 3
4 in 1 Battery Charger
MANUAL
70
300 * 223 * 101 mm
In Full Load : - 20 ~ 60
Automatic adjust fan according to inner temperature
OK
OK
OK
95% (Max)
0.1A
15A (under)
HW-1248C1 for 200~240 Vac Input Voltage
Model No.
HW-1248C2 for 90~130 Vac Input Voltage
50/60 Hz
13.8V
14.5V
450W
30A
12V
8~14.8V
27.6V
29.0V
900W
30A
24V
16~26.4V
39.9V
42.6V
1000W
25A
36V
27~39V
56.5V
53.2V
15A
900W
48V
40~55V
. Specification of 4 in 1 charger
Short Circuit Protection
Reverse Connection Protection
Over Temperature Protection
Protection
Function
Average Charging Voltage
Maximum Ampere Imax
Output Voltage
Current (Without Load)
Maximum Input Current
Input Frequency
Charging Range
Maximum Efficiency in Max. Power
Maximum Output Charging Power
Floating Charging Voltage
Average Temperature in Housing
Dimensions
4.5 Kg
Weight
Operating Ambiance Temperature
Cool System
5%
Voltage / Current Precision
Loading...