Navigator 3000
*
User's Manual
Congratulations
We would like to thank you for choosing a watch from
Tissot®, one of the most highly renowned Swiss brands
in the world.
Your Navigator watch forms part of the Tissot® touch
screen range and benefits from the most recent technical
innovations, including the famous touch screen technology.
Via the touch screen, you can select from the various
functions available, namely the local time and the time
in four other time zones (150 countries and cities stored
in memory), 2 alarms, calendar (automatic* summer/
winter switchover and perpetual calendar up to 2099),
chronograph and timer.
The dual display, analog and digital, informs the user
simply and logically concerning the function selected.
Modern, at once sporty and elegant, and featuring useful
functions, the Navigator 3000 watch will satisfy all men of
action who are frequent travelers.
Important: Your Navigator watch is water-resistant to 5
atm. However, no function can be activated if the crystal is
in contact with a liquid.
* According to the data valid in the country when the watch was programmed
ww w.t is s o t .c h
1/7
140 _ E N / 0 8. 0 6
Navigator 3000
*
Basic principles
Crown
A press for about one second on the crown activates the touch screen,
and can confirm a setting (Enter) and start/stop the chronograph
function and the timer function.
Each setting is confirmed by a short press (< 1 s) on the crown.
Tactile functions
The touch screen is active only after the crown has been pressed
for about one second (activation is confirmed by a beep). It remains
active for 10 seconds after the last operation. Once the touch screen
has been activated, a mere touch of the finger on one of the six
tactile zones of the screen activates the corresponding function,
namely:
the local time function;
1
2
the time function in four other time zones;
3
the timer / incrementing function;
4
the chronograph /
5
the alarm function;
the calendar function.
6
• Once one of these functions has been selected, the display modes
can be changed in succession by touching the same zone again.
decrementing function;
Tactile zones
6
5
1
2
3
4
Incrementing
• The
to enter the function displayed.
• When the digital display indicates , a setting can be
made.
• When the digital display flashes, it is possible either to make
a correction with
pressing the crown (short press < 1 s).
If no operation is performed during 10 seconds, the last setting is
not validated and the touch screen is deactivated.
• After validating a setting, the watch returns automatically to the
time mode and the digital display indicates the last setting made.
• When the crown is pressed, the watch emits a high-pitched beep for
confirmation, while a low-pitched beep indicates an inappropriate
action*.
* You can remove the confirmation sound from your watch; please refer to
the time function in “TONE ON“ mode.
symbol indicates that you have to press the crown
( ) or
3
( ), or to confirm the setting by
4
Decrementing
Lighting Activation/Adjustment
To activate lighting of the digital display, turn
the crown to the left or right. Once the lighting
has been activated, turn the crown to the right to
increase the intensity, or to the left to reduce it.
The lighting remains active for 10 seconds after
the last operation.
ww w.t is s o t .c h
2/7
140 _ E N / 0 8. 0 6
Navigator 3000
*
Local time mode
At delivery, the hands on your watch indicate the local time. The digital
display indicates either the local time, or the region of the local time.
If for whatsoever reason you wish to change the local time, you can select
a new time zone according to the procedure indicated below.
You can also select the display language (French, English, German,
Spanish, Italian and Portuguese), activate the audible alarm or not, and go
into “battery saving“ mode.
Local time setting
Select a continent. Use the tactile zone
or
to scroll the continents.
Confirm by pressing the crown.
Touch the screen several times to select
one of the display modes or to navigate
through to the “SET“ function.
To access the settings, select the “SET“
function and press the crown.
Touch the screen several times
until you reach the setting you
wish to change, then press the
crown to confirm your choice.
Selecting a language
You can select one of the six available
languages: French, German, English,
Spanish, Italian or Portuguese.
Use the tactile zone or to scroll
the languages.
Confirm your choice by pressing the
crown.
Select a country. Use the tactile zone
to scroll the countries.
or
Confirm by pressing the crown.
Confirm your choice by means of
tactile zone
Confirm by pressing the crown.
Add the name of a city
If necessary perform setting of the
hours and minutes by means of tactile
or
zone
Confirm each setting by pressing the
crown.
Note : Setting the second pulse
• from 0 to 30 sec., the display is rounded off to the next lower minute;
• from 31 to 59 sec., the display is rounded off to the next higher minute.
.
or
See Expert mode
.
Deactivating the sound
(except for the alarm bell)
Select the “sound activated“ or
“sound deactivated“ mode by means
of tactile zone or .
Confirm by pressing the crown.
Energy saving
If you plan not to use your watch for
a long period of time, you can select
the “ECO BAT“ mode to economize
2“
the battery. The watch goes into sleep
mode, the LCD screen goes out, and
the hands indicate 6.30 am.
To reactivate the watch, press the
crown for 2“.
5“
Synchronization of
digital time / analog time
See Expert mode.
Exit setting mode.
ww w.t is s o t .c h
3/7
140 _ E N / 0 8. 0 6
Navigator 3000
*
Expert mode
Add the name of a city
To add the name of a city, select the
“NEW“ function by means of tactile
zone or .
Confirm by pressing the crown.
One after the other, select the
letters of the name to be created
by means of tactile zone
letters at most).
Confirm each letter by pressing the
crown.
After the final confirmation, you
can set the time if necessary (see
above).
or
(8
5“
Synchronization of
digital time / analog time
If you detect a difference between
the time displayed by the hands and
the digital display, you can reset the
hands:
When the “ECO BAT“ function is
displayed, press the crown for 5“,
and the hands should be positioned
on midday. Otherwise, they should
then be positioned as indicated
below.
Press tactile zone to move the
minute hand forward;
Press tactile zone to move the
hour hand forward.
Confirm by pressing the crown.
Time zone mode
Through its T-World function, your watch can display the time in four other
time zones, parameterizable. The standard settings give the local time in
New York, Rio de Janeiro, Thailand and Sydney, but they can be changed
by selecting one of the 150 other pre-memorized zones.
You can also select the reference time with the SWAP function, display
the absolute time or the time difference with the ABS function, and even,
in Expert mode, alter the date for changing summer time and winter time
(DST or daylight saving time function).
Absolute time
(GMT)
2“
Time differenceor
2“
Touch the screen to select the desired
region or to navigate through to the
“SET“ function.
To access the settings, select the “SET“
function and then press the crown.
Touch the screen several times
until you reach the setting you
wish to change, then press the
crown to confirm your choice.
ww w.t is s o t .c h
4/7
140 _ E N / 0 8. 0 6
Navigator 3000
*
______
_____
Selecting another time zone
By means of tactile zone
from the four pre-memorized time
zones the one you want to change.
Confirm your choice by pressing the
crown.
First select a destination continent.
Use the tactile zone or to scroll the
continents.
Confirm your choice by pressing the
crown.
Then select a country. Use the tactile
zone
Confirm your choice by pressing the
crown.
Then select a city (if it is available).
Use the tactile zone or to scroll
the cities.
Confirm your choice by pressing the
crown; you then exit setting mode.
to scroll the countries.
or
or
select
,
Change of reference time
By means of tactile zone
from the four pre-memorized time
zones the one you want to use as
reference time.
Confirm your choice by pressing
the crown. This time becomes the
reference time.
Warning!
The “SWAP“ function changes the local time with the time of one of
your time zones. As a result, your local time is now in the “T-WORLD“
function and the time of your time zone can be found in the “TIME“
function.
The alarms are synchronized with the analog display.
or
select
,
Changing the time display
Absolute time - Time difference
Select “T ABS“ to display the absolute
time or “T DIF“ to display the time
difference.
Confirm your choice by pressing the
crown.
5“
DST setting (daylight saving time)
See Expert mode
Expert mode
DST setting (daylight saving time)
5“
From the “T ZONE“ function, press
Note: If you remove the country/city from the “T-world“ function, manual
setting of the daylight saving time will also be eliminated.
the crown for 5“ to access the
“DST“ function.
Confirm to access the settings.
By means of tactile zone or
select from the four time zones the
one you want to change.
Confirm to access the settings.
,
Exit setting mode.
By means of tactile zone or
select the “DST ON“ function to
change the date, or “DST OFF“ to
eliminate the daylight saving time
change.
Confirm to access the settings.
Select the day and month of the
start of daylight saving time for the
current year by means of tactile
zone or .
Press the crown to confirm the
setting.
Select the day and month of the
end of daylight saving time for the
current year by means of tactile
zone or
Press the crown to confirm the
setting.
.
,
ww w.t is s o t .c h
5/7
140 _ E N / 0 8. 0 6
Navigator 3000
*
Alarm mode
Your watch has two different day alarms, which can be set separately over
24 hours and/or over 7 days (see Expert mode).
At the programmed time, an audible alarm is triggered.
To stop the alarm, press the crown briefly.
Note: 5 tunes are available to choose from.
Alarm activated
Alarm not activated
Touch the screen to select alarm 1 or
2 or to navigate through to the “SET“
function.
To access alarm setting, select the
“SET“ function and confirm by pressing
the crown.
Touch the screen several
times to access the alarm
you wish to change, then
press the crown to confirm
your choice.
Setting the selected alarm
Expert mode
Alarm activated
over 7 days
Comments: Day 1 corresponds to Monday, day 2 to Tuesday, and
so on…
By combining your two alarms and the setting for the
days, you can very easily create one alarm for the
week and another for the weekend.
Setting the alarm over 7 days
You can set an alarm so that it
sounds on different days of the
week at a fixed time.
When an alarm is activated,
press the crown for 5“ to access
weekly setting of this alarm.
All the days of the week are
activated by default.
Deselect the days that you don't
wish to activate by means of
the tactile zone or .
Confirm the day and go to the
following day by pressing the
crown.
Activate the alarm by means of the
tactile zone
Confirm by pressing the crown.
(by deactivating the “AL1 OFF“ alarm,
you exit setting mode).
5“
Setting the alarm over 7 days
Select a tune by means of the tactile
zone or .
(the tune sounds after 2“).
Confirm by pressing the crown.
Set the hour and minutes by means of
the tactile zone or
Confirm each setting by pressing the
crown.
.
or
See Expert mode.
.
Chrono mode
Your watch has a chronograph function.
When the period timed is less than 1 hour, the minutes, seconds and
hundredths of seconds are displayed.
When the period timed is greater than 1 hour, the hours, minutes and
seconds are displayed.
Touch the chronograph function on the
screen.
Press the crown to activate the
chronograph.
Press the crown to stop the
chronograph.
Press the crown for at least 2“ to reset
2“
the chronograph.
Exit setting mode.
ww w.t is s o t .c h
6/7
140 _ E N / 0 8. 0 6
Navigator 3000
*
Mode date
Your watch has a calendar function available on the digital display, with
3 modes:
• day/date
• second/date
• week number.
Touch the screen to select the desired
display or to navigate through to the
“SET“ function.
To access the settings, select the “SET“
function and press the crown.
Touch the screen several
times until you reach the
setting you wish to change,
then press the crown to
confirm your choice.
Date setting
Timer mode
Your watch has a timer function. Once the programmed period of time has
elapsed, an audible alarm is triggered.
To stop the alarm, press the crown briefly.
Touch the screen to select the “TIMER“
mode or the “SET“ function.
Press the crown to activate or stop the
timing operation displayed or select the
“SET“ function and press the crown to
set the timer.
Set the hour, minutes and seconds
by means of the tactile zone
Confirm each setting by pressing
the crown. After confirming the last
setting (the seconds setting), the
timer is activated automatically.
A further press on the crown stops
timing.
Note: The last time set remains displayed by default 5 seconds before the
timing ends, and a beep sounds for each remaining second.
or
.
Set the year by means of the tactile
zone
or .
Confirm by pressing the crown.
Set the month and day by means of the
tactile zone
Confirm by pressing the crown.
or
.
Day/Month order of display
Select the month/day or day/month
order of display by means of the tactile
zone or .
Confirm by pressing the crown.
Exit setting mode.
Note: Your watch being set in factory, there is no need to correct the date
Reminder: It is possible to change the language (see Time function).
Care and maintenance
We would advise you to clean your watch regularly (except for
the leather strap) using a soft cloth and warm soapy water.
After immersion in salty water, rinse it in fresh water and leave
it to dry completely. Do not leave it anywhere where it might
be subjected to major variations in temperature or humidity, in
direct sunlight or near strong magnetic fields.
To benefit from the highest standards of service and to ensure
your guarantee remains in force, please always contact an
approved TISSOT® representative or retailer.
TISSOT® Quartz watches benefit from the incomparable
precision of quartz. Their power reserve usually enables them
to operate for more than 2 years in continuous use. If you ever
plan not to be wearing your watch for a period of several weeks,
or even several months, we would advise you to activate the
"economy" mode before putting your watch away. This reduces
the electrical power supply to the motors, thereby extending
battery life considerably.
Replacing the battery
Once the battery has run flat, it must be replaced without delay
by an approved TISSOT ® representative or retailer.
Type : lithium, ref. Renata CR 2025
Note: Battery end of life is indicated to you by continuous
flashing of the digital display.
Collection and treatment of end of life quartz watches*
This symbol indicates that this product should not be
disposed with household waste. It has to be returned to
a local authorized collection system. By following this
procedure you will contribute to the protection of the environment and human health. The recycling of the materials will
help to conserve natural resources.
* valid in the EU member states and in any countries with corresponding legislation.
ww w.t is s o t .c h
7/7
140 _ E N / 0 8. 0 6
Loading...