TIS 875770 User Manual

875770 HDBaseT/HDMI/Audio Matrix

Manual

875770 HDBaseT/HDMI/Audio Matrix 8x8

TLS electronics GmbH [e-mail] 2

Thank you for purchasing this product. For optimum performance and safety,
please read these instructions carefully before connecting, operating or
adjusting this product. Please keep this manual for future reference.

SURGE PROTECTION DEVICE RECOMMENDED

This product contains sensitive electrical components that may be damaged by
electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge
protection systems is highly recommended in order to protect and extend the life
of your equipment.

SAFTY AND NOTICE

1. The transmission distances of HDMI over UTP cables are measured using
TE CONNECTIVITY 1427071-6. The recommended quality of cable is
AWG 24/1.

2. EIA/TIA-568-B termination (T568B) for CAT cables is recommended for
better performance.

3. DO NOT use 568A/568B standard mixed CAT cable (cross-over cable)
because there are 2 pairs swapped, this will make POE OVER-CURRENT
and damage POE components. Please use straight-through CAT cable (both
RJ45 headers are 568A or 568B standard).

4. It is recommended that power up the device after connections of source, sink
and CAT cable.

5. To reduce the interference among the unshielded twisted pairs of wires in
CAT cable, do not run HDBaseT / Zone Cat5e/6/6a cabling with or in close
parallel proximity to mains power cables. Shielded CAT cables can be used
to improve EMI problems, which is worsen in long transmission.

6. Because the quality of the CAT cables has the major effect on how long the
transmission limit can achieve and how good is the received picture quality,
the actual transmission range is subject to one’s choice of CAT cables.

7. Do not substitute or use any other Power Supply other than the
enclosed unit, or a TLS electronics GmbH approved Replacement Part.
Doing so will void the warranty and potentially expose the user to dangerous
voltages resulting in an electrical shock.

8. Do not disassemble the device for any reason. Doing so will void the
manufacturer’s warranty. Also, our unique case is an integral part of the
design of this unit and is responsible for cooling and circuitry shielding. Any
modifications to this case will potentially cause malfunction and product
failure.

9. Do not expose the device to water, moisture, or liquids. Possible electric
shock may result as well as failure of the unit to operate.

875770 HDBaseT/HDMI/Audio Matrix 8x8

TLS electronics GmbH [e-mail] 3

Table of Contents

1. Introduction.............................................................................................4

2. Features.....................................................................................................4

3. Panel Descriptions………………………………………….............................5

4. Remote Control Descriptions……................................................................8

5. Application Diagram.....................................................................................9

6. Specifications.............................................................................................10

7. Package Contents......................................................................................11

8. RS-232 Pin Assignment.............................................................................10

9. RS-232 and Telnet Commands .................................................................12

10. GUI control..............................................................................................14

11. Manual setting of input detection of video source……………………………29

12. Maintenance...............................................................................................30

13. Warranty Policy.......................................................................................30

14. Limitations of Warranty............................................................................30

15. Exclusive Remedies.................................................................................31

16. RMA Policy...........................................................................................31

17. Standard Replacement………………………………………………………31

875770 HDBaseT/HDMI/Audio Matrix 8x8

TLS electronics GmbH [e-mail] 4

Introduction:

HDBaseT/HDMI/Audio Matrix is a modular design 8x HDMI/HDBaseT and 8x
HDMI and 8x HDBaseT matrix switcher together with 24x8 audio matrix switcher,

supporting 1080p Full HD up to 4K plus all 3D formats, along with multichannel
digital audio formats such as Dolby® True HD and DTS-HD® Master Audio™.
Based on HDBaseT technology, the input or output distance can reach up to
100m via Cat5e/Cat6. Embedded Ethernet switcher provides flexible access to
Ethernet for each zone. Each source can be routed to any display using the
front-panel push buttons, IR remote control, RS-232 interface, or via TCP/IP.

Features:

• 2U modular design, flexible input and output cards selection.

• 24x8 stereo audio matrix supporting Audio Return Channel.

• HDBaseT chipset inside for input or output distance up to 100m.

• Matrix can power the remote receivers and transmitters, POH (power over

HDBaseT), no power supply needed for the transmitters and receivers. The
maximum number of supplied transmitters and receivers is 8. For

additional devices you have to use the external power supply, which is
delivered with the transmitter-receiver-set. Do not mix with other
manufacturers !

• Supports resolutions up to 1080p@60Hz,4K@30Hz(4:4:4),4K@60Hz(4:2:0)

• Allows any source to be displayed on multiple displays at the same time

• Allows any HDMI display to view any HDMI source at any time

• Dolby TrueHD and DTS-HD master audio pass through HDMI output

• Advanced EDID management for rapid integration of sources and displays

• Front-panel LCD display for status feedback

• Multiple switching mode, push-in button, Windows Software, IR remote

control, RS-232 control, and TCP/IP control

• Easy installation with rack-mounting ears

• Full 3D pass through.

• HDCP compliant

875770 HDBaseT/HDMI/Audio Matrix 8x8

TLS electronics GmbH [e-mail] 5

Panel Descriptions

Front Panel

1. LCD display---Show the status of input-output selection, EDID info and so on.

2. IR receiver window----Receive the IR from the remote control of

HDBASET/HDMI/AUDIO MATRIX.

3. Power LED indicator---Indicate the status of the power for the matrix.

4. Power button---Press to power on/off the matrix.

5. HDMI output selection button 1 to 8---Press to select the output from 1 to 8.

6. All button for HDMI outputs---Press to select all of the outputs from 1 to 8.

7. Menu button---Press to enter EDID set mode. Three EDID segments will

display on the LCD panel formatted as: INPUT VIDEO AUDIO, for example:
IN1 1080P 2.0CH, means to set 1080P 2.0CH EDID to INPUT1. The blinking
segment is the one can be changed currently. Segment content items as
below:

875770 HDBaseT/HDMI/Audio Matrix 8x8

TLS electronics GmbH [e-mail] 6

INPUT VIDEO AUDIO

Note
IN1 1080I 2.0CH.
IN2 1080P 5.1CH
IN3 3D 7.1CH
IN4 4K2K NONE
IN5 D1024 D1024=DVI 1024 x 768
IN6 D1080 D1080=DVI 1920 x 1080
IN7 D1200 D1200=DVI 1920 x 1200
IN8 OUT1 OUT1=Copy OUTPUT1 EDID to INPUTx
ALL OUT2 ALL=Set EDID to ALL INPUTs

OUT2=Copy OUTPUT2 EDID to INPUTx
OUT3 OUT3=Copy OUTPUT3 EDID to INPUTx
OUT4 OUT4=Copy OUTPUT4 EDID to INPUTx
OUT5 OUT5=Copy OUTPUT5 EDID to INPUTx
OUT6 OUT6=Copy OUTPUT6 EDID to INPUTx
OUT7 OUT7=Copy OUTPUT7 EDID to INPUTx
OUT8 OUT8=Copy OUTPUT8 EDID to INPUTx

8. Up selection button--- Press to change segment’s value.

9. ESC---Press to quit EDID set mode.

10. Lock LED indicator---Indicate the status of Lock.

11. Lock button---Press to lock the buttons of the front panel.

12. HDMI input selection button 1 to 8---Press to select the input from 1 to 8.

13. PTP button---Press to mirror all inputs and outputs (e.g. output 1 to input1,
output 2 to input2 and so on).

14. Selection button---Press to select segment to change setting. Selected
segment will be blinking.

15. Down selection button---Press to change segment’s value.

16. Enter button--- Press to set EDID to specified INPUT or copy EDID from
specified OUTPUT to specified INPUT.

875770 HDBaseT/HDMI/Audio Matrix 8x8

TLS electronics GmbH [e-mail] 7

Back Panel

1. HDMI inputs 1 to 8 --- Connect HDMI sources

2. HDBT inputs 1 to 8 --- Work with remote HDBT transmitter

3. HDMI outputs 1 to 8--- Output for displays, AVR etc.

4. HDBT outputs 1 to 8--- Work with remote receivers for long distance

transmission.

5. Ethernet--- Connect to the LAN switch for Ethernet access, embedded 1x16

Ethernet switch for remote 8x HDBT transmitter and 8x HDBT receiver

6. RJ45 ---TCP control

7. Power switch--- Power on/off the unit.

8. GND---Connect to ground.

9. RS232 port--- 1x 3-pin phoenix terminal connector

10. L/R In 1 to 8--- 3.5mm stereo phone-jack.

11. IR Out 1 to 8---3.5mm mono phone-jack, connect to IR transmitter cable.

12. Coaxial Output 1 to 8 ---RCA connector.

13. L/R Output 1 to 8 ---3.5mm stereo phone-jack.

14. IR In 1 to 8 ---3.5mm stereo phone-jack, work with control processor.

15. Master RS232---1x 3-pin phoenix terminal connector

16. Global IR Out--- 3.5mm mono phone-jack,

17. Global IR In--- 3.5mm stereo phone-jack.

18. AC power input---100-240V power input.

875770 HDBaseT/HDMI/Audio Matrix 8x8

TLS electronics GmbH [e-mail] 8

Remote Control Description





875770 HDBaseT/HDMI/Audio Matrix 8x8

TLS electronics GmbH [e-mail] 9

Output and Input select

A. OUTPUT-X select INPUT-Y:

1. Pre ss OUTPUT-X (X means 1 to 8 of outputs)ÆPress INPUT-Y ( Y means
1 to 8 of inputs )

2. Press OUTPUT-X (X means 1 to 8 of outputs)Æ press the left and right
arrow buttons to select the input.

B. All outputs select INPUT-Y: Press ALL button in zone OUTPUTÆPress
INPUT-Y button ( Y means 1 t o 8 of inputs ), then INPUT-Y switched to ALL
OUTPUTS
C. Mirror all inputs and outputs (Ex. Input 1 to output 1, input 2 to output 2, etc):
Press PTP button in Zone OUTPUT





EDID Set Up

A. Fixed EDID to INPUT-Y/ALL

Press 1080I/1080P/3D/4KÆ
Press 2.0CH/5.1CH/7.1CHÆ
INPUT-Y/ALL button in Zone INPUT

B. Copy EDID of OUTPUT-X to INPUT-Y/ALL

Press COPY buttonÆPress OUTPUT-X buttonÆPress INPUT-Y/ALL button

C. User defined EDID to INPUT-Y/ALL

Press USER1/USER2 buttonÆPress INPUT-Y/ALL
NOTE: Pressing button sequence should be finished in 5 seconds, otherwise,
operation discarded.

Application Diagram

Cover page no. 4

875770 HDBaseT/HDMI/Audio Matrix 8x8

TLS electronics GmbH [e-mail] 10

Specifications:

Bandwidth：

10.2Gbps

Video Input Connectors: 8x HDMI Type A, 8x RJ-45 connector
Video Output Connectors: 8x HDMI Type A, 8x RJ-45 connector
Audio Input Connectors: 8x 3.5mm stereo jack
Audio Output Connectors: 8x 3.5mm stereo jack,8x RCA (SPDIF)
Ethernet Input: 1x RJ-45
RS-232 serial port: 9x 3-pin phoenix terminal connector
TCP/IP Control: 1x RJ-45
IR Input ports: 9x 3.5mm stereo jack
IR Output ports: 9x 3.5mm mono jack
Rack-Mountable: 2 U rack height, rack ears included
Dimensions (W x H x D): 440mm x 358mm x 87mm , without

feet
Shipping Weight: 8.8Kg
Operating Temperature: 32°F to 104°F (0°C to 40°C)
Storage Temperature : -4°F to 140°F (-20°C to 60°C)
Power Supply: 100V-240V

Package Contents:

1. 1x 875770 HDBaseT/HDMI/Audio Matrix XxX

2. 1x AC power cord

3. 1x Remote control

4. 9x IR Transmitter,

5. 9x IR Receiver.

6. 1x mounting kit.

7. 2x RS232 to Philex Cable