Tiras PRIME 8L User Manual

FIRE ALARM SYSTEMS

FACP «TIRAS PRIME 8L»

User Manual

ААZCh.425521.014 UM

DSTU ISO 9001:2015

Serial number:

FW version: PRIME8L_1

2

Thank you for choosing

equipment produced by Tiras-12 Ltd.

Before using the product,

please refer to this document *

and save it to receive

the necessary information in the future.

For more information

and loading the documentation

use the following links:

www.tiras.ua

DOCUMENTS:

User manual

Installation

manual

APPLICATIONS:

tLoader

(Windows)

tLoader

(Android)

* - this manual is intended for built-in firmware PRIME8L_1

3

Fire Alarm Control Panel «Tiras PRIME 8L» complies with essential requirements of the

following European Union Regulations and Directives:

- Construction Products Regulation (EU) No 305/2011;

- Low Voltage Directive 2014/35/EU;

- EMC Directive 2014/30/EU;

- Directive 2011/65/EU (RoHS).

Fire Alarm Control Panel «Tiras PRIME 8L» complies with requirements of the following

European Union standards:

- EN 54-2:1997+AC:1999+A1:2006;

- EN 54-4:1997+AC:1999+ A1:2002+A2:2006
The EC Certificate of Constancy of Performance No 1438-CPR-0647 was issued by the

CNBOP-PIB Notified Body

1438

«Tiras-12» LTD

2nd Lane Khmelnytske Shosse, 8, Vinnytsia, Ukraine, 21021

Fire Alarm Control Panel «Tiras PRIME 8L»

EN 54-2:1997+AC:1999+A1:2006;
EN 54-4:1997+AC:1999+ A1:2002+A2:2006

Main provided functions:

− Output to fire alarm devices

− Alarm transmission routing equipment

− Fault warning routing equipment

− Total loss of the power supply

− Dependencies on more than one alarm signal

− Delay to outputs

Information about additional functions, inputs and outputs specified in this manual.

The Quality Management System of the «Tiras-12» LTD is certified according to DSTU ISO

9001:2015. Certificate № UA 8О050.008QMS-18 with effect from 27.04.2018 to 26.04.2021.

The full text of the declarations of conformity to technical regulations and certificates is

available on the website at the following address: www.tiras.ua.

4

Contents

1 Abbreviations ................................................................................................................................... 5

2 Terms and definitions ..................................................................................................................... 5

3 Function and structure of FACP ..................................................................................................... 5

4 General information ........................................................................................................................ 6

5 Specifications.................................................................................................................................... 6

6 Safety requirements ........................................................................................................................ 8

7 Structure and operation.................................................................................................................. 8

7.1 Terminals for connection of primary module .................................................................. 11

7.2 Operation ............................................................................................................................. 11

7.2.1 Indication..................................................................................................................... 11

7.2.2 Controls ....................................................................................................................... 12

7.2.3 FACP operation modes (Conditions) ........................................................................ 13

7.2.4 Access levels ................................................................................................................ 14

7.2.5 Level 1 (View) ............................................................................................................... 14

7.2.6 Level 2 (Control) .......................................................................................................... 14

7.2.7 Level 3 (Configuration) ............................................................................................... 19

7.2.8 Level 4 (Service) .......................................................................................................... 19

8 Maintenance ................................................................................................................................... 19

8.1 General ................................................................................................................................. 19

8.2 Replacing battery of real time clock .................................................................................. 20

8.3 Battery fuse .......................................................................................................................... 20

8.4 Main power source fuse ..................................................................................................... 20

9 Package contents ........................................................................................................................... 20

10 Manufacturer declarations ............................................................................................................. 21

11 Certificate of acceptance ................................................................................................................. 21

12 Certificate of re-acceptance ............................................................................................................ 21

13 Operation and storage conditions .................................................................................................. 21

14 Warranty obligations ...................................................................................................................... 21

15 Limitation of liability ........................................................................................................................ 21

16 Repair ............................................................................................................................................. 22

17 Disposal .......................................................................................................................................... 22

Appendix A. Wiring diagram............................................................................................................ 23

5

This manual contains a description, operating rules and passport data of the fire alarm

control panel (further – FACP) – Tiras PRIME 8L.

FACP meets the mandatory requirements of EN54-2, as well as the following optional ones:
outputs to fire alarm devices, output to alarm transmission routing equipment, output to fault
warning routing equipment, delays of outputs, dependencies in zones. FACP contains a built-in
power supply unit (further - PS), meeting the requirements of EN54-4.

In order to avoid possible errors in operation and damage of the equipment, it is
necessary to read carefully this manual and installation manual (AAZCH.425521.014 IM) before
using control panel.

1 Abbreviations

The following abbreviations are used in this document:

FACP

– fire alarm control panel;

FARS

– fire alarm receiving station;

PC

– personal computer;

ATS

– alarm transmission system;

SC

– short circuit;

PS

– power supply;

IM

– Installation Manual for FACP (www.tiras.ua)

2 Terms and definitions

Fire Alarm System (FAS) – group of components installed in the system of the definite
configuration, which is capable of detecting and indicating fire and of signaling to take the
appropriate measures;

Detector – FAS component containing at least one sensor that permanently or
periodically monitors at least one physical and / or chemical phenomenon associated with fire
at a low interval of time and produces at least one corresponding signal to FACP;

Fire Alarm Device (Siren, Sounder) – sound or light and sound device designed to alert
people on the need to evacuate from areas with a fire detected;

Zone – certain part of protected premises, in which one or more components are installed
and for which a general status indication is provided;

Verification (Dependence) – software function, used to confirm the triggering of detector
by checking that it is re-triggered by automatic reset or expecting the triggering of two
detectors in one or more detection circuits or zones;

Communicator – device, intended for transmitting messages to FARS;

Expansion Module – device, designed to increase the number of zones and (or) outputs.

3 Function and structure of FACP

FACP is designed to:

• Control the state of fire detectors;

• Control the sounders;

• Control the external devices;

• Control the state of external devices;

FACP is the basis for constructing FAS to which you can add:

• Module for expansion the number of zones M-Z(f). Is installed on FACP board;

• Relay module for 4 relays M-OUT4R. Is installed on FACP board;

6

4 General information

Features of FACP:

• 8 zones (expanded up to 20 zones with M-Z(f) module);

• Up to 32 detectors in each zone;

• Verification in one or more zones;

• 2 controlled outputs for sounders;

• Fire and Fault outputs;

• 2 programmable relay outputs;

• Controlled power supplies + 24V;

• LCD display with backlit;

• Day-Night mode for controlling delayed activation of outputs;

• Programming scripts for inputs and outputs;

• Settings with PC or Android device (via USB);

• Non-volatile clock and event log for 1000 events;

• Alternative power supply – 2 batteries, with the capacity of 7 Ah;

• Intelligent charging device with battery capacity control;

• Powerful pulse power supply 24V/2A;

5 Specifications

Table 5.1 – Features of FACP

Parameter name

Value

Main power supply: AC power voltage, V

230, +10%, -15%

Main power supply: AC power frequency, Hz

501

Maximum consumption current from main power supply, A

0.27

Maximum power consumption from main power supply, VA

60

Alternative power supply: two sealed lead-acid batteries with the
voltage of, V (each)

12

Alternative power supply: two sealed lead-acid batteries with the
capacity of, Ah (each)

7

Maximum charging current of battery, mA

500

Maximum permissible internal resistance of battery cells and their
connection circuits, R

imax

1

, Ohm

1,0

Output voltage UPS, V

19 - 29

Ripple of the output voltage UPS, mV, not more than

400

Minimum current consumption from the UPS in Quiescent condition,
Imin 1, A

0,08

Minimum current consumption from UPS in Fire condition, A

0,11

Maximum long-term current consumption from UPS with maximum
loads, Imax_a 1, A

0,91

Minimum current consumption from battery in Quiescent condition
(without display backlighting, for calculation of backup power supply), A

0,075

Maximum load current of +24V outputs (each), mA

400

Dimensions (W x H x D), mm

350 x 370 x 96

7

Net weight (without battery), kg, not more than

2,5

Average time to failure, hours, not less than

40000

Average lifetime, not less than

10

Enclosure protection degree (IEC 60529)

IP30

Inputs and outputs

Number of zones (base/extension), pcs

8/20

Number of detectors in each zone, pcs, not more than

32

Voltage in zone in Quiescent condition, V

18 - 21

Current in zone in Quiescent condition, mA

3,0 – 5,5

Maximum current in zone (SC), mA

43 ± 3

Resistance of leakage in zone (between each wire and ground),
kOhms, not less than

50

Resistance of detection circuits (zones), Ohms, not more than

250

Resistance of the terminal resistor, kOhms

6,8 ± 1% (3,9 ± 1%)2

Resistance of the terminal resistor of the system bus, Ohm

120

Switching current of S1+ and S2+ outputs, A, not more than

3

Switching voltage of S1+ and S2+ outputs, V, not more than

24

Switching current of relays REL1 and REL2, A, not more than

3

Switching voltage of relay contacts REL1 and REL2, V, not more than

- direct current

- alternate current

24

120

Switching current of outputs FT and AL, mA, no more than

100

Fuses

AC 3, A

3.15, fusible

Battery3,A

1.85, resettable

Additional loads, outputs +24V,A

2 x 0.5, resettable

Fire and Fault outputs, A

0.5, resettable

Power supply of communicator, A

0.2, resettable

Time characteristics

Zone reaction time to alarm (fault), sec, not more than

10

Time to defect faults (except zones), sec, not more than

100

Time to detect the capacity of battery (low capacity), min, not more
than

15

Time to detect the absence of battery, min, not more than

2

Cross-section of wires4 allowed for clamping in terminals, mm2

0,22 - 1,5

1

-according to EN54-4

2

-using terminating resistors 3.9 kΩ, the consumption of FACP in all conditions increase by

25 mA.

3

- accessible only from 3rd access level.

4

- cross-section of wires is indicated for copper multi-conductor wires.

8

6 Safety requirements

6.1 Installation, uninstallation, operation and maintenance of FACP shall be carried out

by qualified personals in accordance with the electrotechnical regulations and fire safety
regulations.

6.2 Installation, uninstallation and maintenance of FACP must be carried out with the

power supply disconnected.

7 Structure and operation

The appearance of FACP Tiras PRIME 8L is shown in Fig. 1. The appearance with the front
cover removed is shown in Fig. 2. The appearance of the housing without the main module is
shown in Fig. 3. The view of the main module is shown in Fig. 4 and Fig. 5

Figure 1 – Appearance of FACP

All connections must be carried out with disconnected all power sources
of FACP: main (230 V AC) and alternative (batteries)

Caution! Printed circuit boards of FACP and modules contains static-sensitive

components. To avoid damaging the sensitive components always ground
yourself before handling any boards

Caution! Installing and removing modules should be carried out with
disconnected power sources (AC and DC) to avoid damaging of main board and
modules.

9

Figure 2 – Appearance of FACP without front cover:

1. Slot for battery; 2. Holes for mounting and fixing on the wall (see. IM);

3. Holes for wiring; 4. Main module (control and indication panel with connection

terminals); 5. Holes for fixing main module with self-tapping screw (after installation is

complete).

Figure 3 – Appearance of the housing without main module of FACP:

1. Holes for wiring; 2. Main supply unit; 3. Terminals for connection to power supply 230V;

4. Slot for installation of additional modules; 5. Additional hole for fixing on the wall.

10

Figure 4 – Main module with control and indication panel:

1. Indicators LED1 and LED2 (see details in IM); 2. miniUSB socket; 3. Terminals for

connection (description is given in table 7.1); 4. Display; 5. Keypad; 6. LED indicators.

Figure 5 – Rear side of the main module:

1. Main PCB; 2. Connector for M-OUT4R; 3. Indication board connector;

4. Communicator connector; 5. START button; 6. PS connector;

7. M-Z(f) connector.

11

7.1 Terminals for connection of primary module

Table 7.1 – Description of terminals for connection

Terminal

Designation

GND

Logic ground

Z1-Z8

Connection of zones (inputs)

S1, S2

Sounders control outputs

US1, US2

Sounders power supply inputs

FT

Output to fault warning routing equipment

AL

Output to fire alarm routing equipment

REL1, REL2

Programmable relay outputs

NC

Normally closed relay contact

NO

Normally open relay contact

+24V

Power outputs 24V

A1, B1

Terminals for connection of system bus (RS-485)

Wiring scheme is given in Appendix A.

7.2 Operation

7.2.1 Indication

Table 7.2 – FACP indication

Indicator

Colour

Name

Indication

Green

Power supply

Lighting –FACP is powered on

Red

General fire

Blinking – fire alarm in one or several
zones

Red

Verification in zone

(zones)

Blinking – verification in one or several
zones

Red

Transmission of

fire alarm signal/

Checking of

transmission

Blinking – fire alarm signal is
transmitted to FARS
Lighting – received confirmation on
transmission of fire signal to FARS

Yellow

General fault

indicator

Blinking – fault in at least one of the
controlled circuits or functions

Yellow

Central monitoring

station «Fire»

output

Blinking – fault of AL output (Fire)
connection circuit or fault of
communicator

1

Lighting – AL output and transmission
of fire alarm to FARS is disabled

Yellow

Central monitoring

station «Fault»

output

Blinking – fault of FT output (fault)
connection circuit or fault of
communicator

1

Lighting – FT output and transmission
of fire alarm to FARS is disabled

Yellow

System error

Blinking – system (program) error of
FACP

12

Indicator

Colour

Name

Indication

Yellow

System bus

Blinking – fault of system bus

Red

Activation of fire

extinguishment2

Lighting – fire extinguishment device is
in “Extinguishing” mode

Red

Activation of fire

extinguishment

delay2

Blinking – fire extinguishment device is
in “Activation” mode

Yellow

Fault of fire

extinguishment2

Blinking – detected fault in fire
extinguishment device

Yellow

General

disablement

indicator

Lighting – at least one disabling is
detected in the system

Yellow

Main power supply

Blinking – fault of main power supply –
230V

Yellow

Backup power

supply

Blinking – fault of backup power supply

Yellow

Outputs

+24V/External

devices

Blinking – fault of one of outputs +24V /
fault of connection line to zones-inputs

Yellow

Grounding control

Blinking – fault (missing) protective
grounding

Yellow

Delay

Lighting – delay function is off (or
NIGHT mode is activated)
Blinking – delay activation

Yellow

Sounders

Lighting – sounders outputs are off
Blinking – fault of at least one of the
sounders outputs

Green

Access

Lighting – access to 2nd level is
completed

1

– blinking of both indicators "FARS fire" and "FARS fault" indicates a fault of the

communicator.

2

- active with a fire extinguishing device connected.

7.2.2 Controls

Table 7.3 – Controls of FACP

Button

Function

Required access level (see 7.2.4)

Disable current delay

1

Enable / disable delay function

2a

Enable / disable sounders outputs

2a/2b

Disable internal buzzer (Silencing)

1

13

Button

Function

Required access level (see 7.2.4)

Reset FACP

2b

Back (to menu)

1

Select active field on display:

(fire - fault - disable )

Main (Go to main menu)

2a/2b

Function 1 (menu of the 3rd access level)

3

Function 2 (menu of the 2nd access level)

2a/2b

Keypad

1

Deleting

2a/2b/3

Access

2a/2b/3

7.2.3 FACP operation modes (conditions)

FACP can be in one of the following operating modes:

• Quiescent – no other conditions, only green indicator lighting, display shows

the information on device name and current time

• Fire – indicator blinking, zones with fire are showed on display, buzzer is

activated;

• Verification – indicator blinking, zones with verification are showed on

display in Fire field. Activation of buzzer. This condition may change to Fire only
upon confirmation of fire according to special algorithm, which is assigned during
programming from the 3rd level of access. If during the programmed time fire is
not confirmed, Verification condition of FACP is changed to Quiescent condition.

• Fault – indicator and indicator of fault zone or circuit blinking, fault function

is showed on display, buzzer is activated;

• Disabled – indicator lighting, showing disabled circuit. Displays the disabled

circuit or zone on display;

14

• 2

nd

access level – indicator on the button lighting. Shows the 2nd access level

menu on the display.

• 3

rd

access level – no indication, no information on display, used for configuration

of FACP. See the details in the guidance on installation (see IM).

FACP can be in Fire, Verification, Fault, and Disabled conditions at the same time. The
display of FACP consists of 3 fields - Fire, Fault and Disabled. In case of a fire, the display
automatically goes to the Fire field on display. With a large number of fire messages, the
messages on fire alarm are always the first in the upper field of the display.

7.2.4 Access levels

FACP has four access levels: View (1st level), Control (2nd level), Configuration (3rd level),
Service (4th level).

The following audible indication is possible when working with keypad:

• 1 short beep - character input / button pressing;

• 2 short beeps - confirmation of section input / function selection;

• 3 short beeps - Enter/Exit from the 2

nd

access level, FACP start;

• 1 long signal - wrong code or symbol entered / performed reset to factory defaults;

7.2.5 Level 1 (View)

Allows getting the information without any operations and perform the following
functions:

• Turn off buzzer (if active) – button .

• Disable delay - button (if Verification condition is active for zone of C-type);

• Switch active display fields (Fig. 2) – button ;

• View main menu (information on FACP) – button

Figure

6 –

Example of active display fields

(Fire, Fault, Disable).

7.2.6 Level 2 (Control)

Level 2 (Control) has 2 sublevels with different permissions:

• Level 2a (User)

• Level 2b (Administrator)

Access to level 2a and 2b is protected with password.

Factory passwords:

level 2a – [1];
level 2b – [1111].

On 2a level (User) one may do the following:

• Enable/disable delay;

• Turn on/off the alert.

15

On 2b level (Administrator) one may do the following:

• Enable/disable delay;

• Reset Fire condition;

• Enable/Disable sounders outputs.

• View event log;

• Enable/Disable Fire and Fault outputs and communicator (if both outputs are

disabled);

• Enable/disable signaling system for fire extinguishment system (if configured);

• Enable/Disable zones of FACP and M-Z(f) (if installed);

• Change the names of zones;

• View information about FACP (version and revision of software, serial number)

• Select interface language;

• Test indication on FACP;

• Change access codes of level 2 (for existing users)

• Set time and date;

• Export event log to the disk of FACP;

• Fast restart of FACP (to go to the access level 3), see detailed information in IM.

7.2.6.1 Operation on 2nd access level

In order to enter the menu of the access level 2b, press the button , enter the access

code requested and confirm it, by pressing the button - LED on the button is lighted

up.

Functions of buttons in different submenus of access level 2b may vary, in such case the

current condition of buttons is indicated at the bottom of the display string.

User automatically exits access level in 20 seconds after last pressing of any button.

Reset Fire or Verification condition:

• Press the button , to mute buzzer (if necessary)

• Press the button ;

• Enter access code of the 2nd access level;

FACP switches to Quiescent condition in 10 seconds.

One can reset Fire condition only when Fire field is active on display, see
sec. 5.1.

You can reset Fault condition the same way as Fire condition. In case of the
loss of the main power supply, 230V, fault indication turns off automatically
after power is restored.

If Fire or Fault conditions appear again after reset, please contact your
service company (installed your system).

16

Table 7.4 – Menu structure of access level 2b.

1: Event log

• Time: Event

• …

2: Disable outputs

• Output name (state)

• …

3: Disable zone

• Zone No.1 (state)

• …

4: Zones names

• Z1: Name

• …

5: Day/Night

6: Device info

7: Menu language

• Українська

• Русский

• English

8: Indication test

9: Change password

• No.1 Name

• …

10: Time and date

11: Export event log

12: Restart

1: Event log (fig.7):

• Enter menu of access level 2b;

• Select menu “1:Event log” and press ;

• Use keypad arrows and to select the message needed, for details, press

Figure 7 – Example of indication on the display in the "Event Log" menu and event

detailing

2: Disable outputs:

Disable/enable sounders:

• Enter menu of access level 2b;

• Select menu “2:Disable outputs” ;

• Using arrows and on keypad and go to Sounder1 and/or Sounder2 and

press to select the state – Dis./En.

When disabled - LED indicator lighting as well as that on the button , display
shows "Disable sounders" in the Disable field.

17

You can also disable sounders outputs without entering the menu of access level 2b – by

pressing button and entering access code level 2. This disables both Alert outputs of FACP
simultaneously.

Disable/Enable Delay function:

• Enter menu of access level 2b;

• Select menu «2:Disable outputs »;

• Using arrows and on keypad and go to Delay and press to select the

state – Dis./En.

When the power is switched off, the indicator lighting, and the display shows a
message on delay shutting down the in the Disable field.

When this function is disabled all configured delays for a zone with verification of type C
are cancelled (see section 5.3.1).

The delay can also be deactivated without entering the menu by pressing the button
and entering the access code (level 2a or 2b).

Disable/Enable Fire Alarm and Fault outputs or communicator (function of
messages sending to monitoring station):

• Enter the menu of access level 2b;

• Select menu «2: Disable outputs»;

• Using arrows on keypad and go to Output AL and Output FT, then press

and select state - Dis./En.

• When both outputs are disabled, the function of messages sending to monitoring

station (device) is off.

When disabled and indicators and/or light, the display shows the
appropriate disabling in Disable field.

Disable/Enable signals to fire extinguishment devices:

• Enter menu in access level 2b;

• Select menu «2:Disable outputs»;

• Using arrows and on keypad go to «Ext.REL (x)» (where “x” is an output of

FACP, set to a fire extinguishment mode. In other modes it is not used) and press

to select the state – Dis./En.

When disabled – indicator lighting, the display shows the message in the «Disabling»

field.

3: Disable/enable zones:

• Enter menu of access level 2b;

• Select menu «3:Disable zones»;

• Using arrows on keypad and go to zone(s) needed, then press and

select the state of zone – Dis./En.

18

When zone is disabled – indicator lighting, the display shows the current quantity of
zones and their numbers.

4: Zone names:

• Select menu «4: Zone name »;

• Using arrows and on keypad and go to the zone needed and press button

;

• Using instructions on the display, enter zone name with the help of buttons-arrows

on the keypad , , and .

5: Day/Night:

• Enter the access level menu 2b;

• Select menu "5: Day/Night";

• Using FACP keypad, select the state – Off/On. Enter the start time - Day and the

start time - Night in the format of HH:MM, (where HH are hours, and MM are
minutes);

• Press the buttons and .

6: Info (fig. 8):

• Enter the access level menu 2b;

• Select menu «5: Information» using button .

Figure 8 – Example of Indication on display in FACP info viewing mode

7: Menu language

• Enter menu of access level 2b;

• Select menu «7:Menu language»;

• Select the language you want using buttons and on the keypad and press

, the available languages are Ukrainian, Russian and English;

• Confirm, by pressing button

8: Indication test:

• Enter menu of the access level 2;

• Select menu «8: Indication test»;

All the indicators of FACP and all the fields must light up for up to 3 seconds and all the
display fields are filled with black;

9: Change password:

• Enter menu of access level 2b;

• Select menu «9: Change password»;

19

• Using buttons-arrows on the keypad and , select the user, then press

button ;

• Enter new password and press buttons and .

The maximum length of code is 10 symbols.

10: Time and date:

• Enter menu of access level 2b;

• Select menu «10: Time and date»;

• Enter date and time in the following format “HH:MM DD/MM/YY”, (where HH are

hours, MM are minutes, DD are days, MM are months, YY are years);

• Press buttons and .

11: Export event log:

• Enter menu of access level 2b;

• Select menu «11: Export event log»;

• Confirm export – press button .

After this operation, EXP_LOG.TXT is created on the disk of FACP, it contains the
information similar to that available in "1: Event Log" menu. Access to file is provided at the
3rd access level

12: Restart:

• Enter menu of access level 2b;

• Select menu «12: Restart»;

• Confirm restart – press the button .

This function is used for quick restart of FACP and/or switching to 3rd access level (for
details - see. 5.3).

7.2.7 Level 3 (Configuration)

Configuration is limited with the use of a tool - a screwdriver. Enables to install or replace
additional modules and to configure FPCs. The description is given in the installation manual.

7.2.8 Level 4 (Service)

Repair of FACP and replacement of software and hardware. Access to the 4th level is
available with a special instrument and is performed by the manufacturer.

8 Maintenance

8.1 General

1.Using a dry cloth, remove any dust that may have gathered on the FACP enclosure.

2. Check the integrity of all wires and connections.

3. Ensure that there are no foreign objects, insects or animals inside the FACP.

Caution! Do not use cleaning agents or solvents!

20

8.2 Replacing battery of real time clock

Real-time non-volatile clock is powered by Li-Ion battery (CR2032), its service life is up to
5 years, after that it is recommended to replace the battery:

• Disconnect main and backup power supply of FACP;

• Disconnect the PS connector (Fig. 5, item 6);

• Disconnect the communicator and M-OUT4R module (if installed);

• Remove the screws for fixing the main board on the main module (Fig. 5);

• Remove the main board from the connector of the display board (Fig. 5, item 3);

• Replace the battery with a new one (XS2 connector, fig. 9);

• Carry out a reverse procedure for assembling FACP.

The location of the battery is shown in Fig. 9

Figure 9 – Location of battery on the main PCB of FACP

8.3 Battery fuse

The battery connection is protected by a self-recovering fuse, the rated current is 1.85A.
This fuse does not require maintenance.

8.4 Main power source fuse

A slow action fusible fuse is installed in the main power supply (fig. 3), which cannot be
independently replaced and not serviced. The access to it is available from 4th access level. Its
fault signals on the need for repair or replace the PS.

9 Package contents

After you unpack FACP, please check its appearance and make sure there are no
mechanical damages, check the completeness, the list of package is presented in table 9.1.

Table 9.1 – Package contents of FACP

Name

Marking

Number

Note

FACP

Tiras PRIME 8L

1

User manual

AAZCH.425521.014 UM

1

Resistor 6.8 kOhm, 1%, 0,5 W

12

Jumper for batteries

1

Screws (fixing the module of main PCB)

2.9 x 9.5

2

Plug 1

Battery

7 Ah, 12 V

2*

* optional request
M-Z(f) 1*

21

10 Manufacturer declarations

Construction of FACP is designed in accordance with the quality management system that
contains a set of design rules for all elements. All the components of FACP were selected for the
purpose and conditions of their use meet the conditions outside the body according to IEC 60721-3-3
Class 3k5.

11 Certificate of acceptance

FACP meets the technical specifications and requirements of acceptance and is approved as

suitable for exploitation.

The serial number and date of production are indicated in the upper right corner of the front of
the cover of this manual. The acceptance date (stamp) is on the back of the title page of this manual.

12 Certificate of re-acceptance

FACP, which is stored in the warehouse of "Tiras-12" LTD for more than six months, must be re­accepted before shipment. You can find the check mark on the last page of the manual.

13 Operation and storage conditions

FACP is designed for 24h operation in premises with regulated climatic conditions without the
direct influence of climatic factors of the environment. The operating temperature range is -5 ...+40ºC,
the relative humidity of air has to be not more than 93%.

The storage temperature in warehouses must be within the range -50 ...+40ºC, the relative
humidity has to be not more than 98% at the temperature of 25ºC. The air in the premise where FACP
is stored, must not contain aggressive impurities causing corrosion.

Packed FACPs are transported at the temperature of -50°C …+50°C, relative humidity of air has to
be up to 98% at the temperature of +25°C for any distance by road, rail (in covered vehicles) or by water
transport (in ship holds). Transportation must be carried out in accordance with the rules applicable for
each type of transport.

Placement and fastening of boxes with packaged products during transportation must ensure
their stable position; exclude the possibility of their impacts between each other and the walls of
vehicles.

14 Warranty obligations

FACP repair is carried out by the manufacturer. FACP is subject to free repair, in case the warranty
is not expired, and the device was operated and installed in accordance with this manual and Installer
manual. FACP is sent for repair with a letter, which should include: the nature of the fault, the location
of FACP, and the contact number of repair specialist.

15 Limitation of liability

The manufacturer reserves the right to refuse warranty service of the device in controversial
circumstances. The manufacturer also has the right to make a final decision on whether the device is
to be serviced under the warranty.

Actions and damages that result in loss of warranty service:

• damage caused by natural phenomena (fire, flood, wind, earthquake, lightning, etc.);

• damage caused by a violation of the installation rules or the provision of improper conditions

for the operation of the device, including:

- faulty grounding;

- over-voltage of the power supply;

- high humidity and vibration;

• damage caused by foreign objects entering the device, liquids, insects and others;

• mechanical damage to components of the device;

• damage resulting from unauthorized repair;

22

• damage caused by violation of the rules of transportation, storage and operation;

• changing, removing, rubbing or damaging the serial number of the device (or labels with serial

numbers on the device).

16 Repair

The FACP is repaired by the manufacturer.
This FACP is repaired for free, in case the warranty period is not expired, it was operation in

accordance with this passport.

The FACP is sent for repair, together with a letter, which should include: the description of the

malfunction, the place of operation and the contact phone of the person in charge of repair.

17 Disposal

After the expiry of the service life of the FACP and the batteries used for it, their utilization is carried
out in accordance with the current legislation, separate from household waste..

In accordance with the EU Directive 2012/19/EU on waste electrical and electronic
equipment, the disposal of FACP should be done separately from household waste. To
dispose of the equipment it must be delivered to a sale point or a local processing point

According to the EU Directive 2006/66 / EU, the disposal of lithium batteries (contains in
the FCP) and batteries used with FACP should be carried out separately from household
waste.

23

Appendix A. Wiring diagram

Edited – 25.06.2019

www.tiras.ua

Manufacturer:

«Tiras-12» LTD

21021 Ukraine, Vinnytsia, 2nd lane Khmelnytske shosse, 8

In any questions, please, contact:

Sales department:

Technical department:

Warranty and post-warranty service:

[e-mail]

[phone],
[phone],
[phone],
[phone],
[phone]

[e-mail]

[phone],
[phone],
[phone],
[phone],
[phone]

[e-mail]

[phone],
[phone],
[phone],
[phone],
[phone]