Z8000
+
RESET DIRECTI ON CLOCK
RESET DIRECTI ON CLOCK
Z8 0 00 Ma t ri x S eq u en c er /Pr og r am m er
1
2
3
4
A
B
C
D
+
User Manual
A
1
2
3
4
B C D
CVA CVB CVC CVD
DIR
CK
RT
Tipt p
A u d i o
+
CV1
CV2
CV3
CV4
DIR
CK
RT
+
Z8000 Matrix Sequencer/Progarmmer
Design - Gur Milstein
Special Thanks
Alessandro Cortini
Andreas Schneider
Andreas Wetterberg
Bobby Voso
James Cigler
Mark Pulver
Matthew Davidson
Matrix
Richard Devine
Shawn Cleary
Surachai Sutthisasanakul
MADE IN THE USA
Tiptop Audio 2010 All Rights Reserved
Introduction.
The Z8000 Matrix Sequencer is a powerful tool in a
small package. Contained within it's structure are
the following:
a) Four 4 step sequencers on the horizontal (1/2/3/4).
b) Four 4 step sequencers on the vertical (A/B/C/D).
c) One 16 step sequencer aggregating all four
horizontal 4 step sequencers in order from
top to bottom, left to right ( ).
d) One 16 step sequencer aggregating all four
vertical 4 step sequencers in order from left
to right, top to bottom ( ).
Thus, giving you a total of ten sequencers in all.
+
RESET D IRECTION CLOCK
RESET D IRECTION CLOCK
+
Z8 00 0 Ma tr ix S eq u en ce r/ Pr og ra mm er
1
2
3
4
A
B
C
D
A
B C D
1
2
3
4
CVA CVB CVC CVD
DIR
CK
RT
Tipt p
A u d i o
+
CV1
CV2
CV3
CV4
DIR
CK
RT
+
Inputs/Outputs.
Each and every sequence has its own individual CV
output as well as Clock, Direction & Reset inputs.
The grouped 4 step sequencers each share a
normalized connection to the Clock. Allowing, for
instance; a single clock to guide all four horizontal 4
steps from only one connection. The same applies for
the four vertical sequences. (ex: plugging in a new
timing signal into the third Clock while the first Clock
still has its jack in place would make sequences 1 & 2
of the group run at a separate rate than sequences
3 & 4.) On the other hand Direction & Reset Inputs
are not normalized in order to keep these functions
independent. The Tiptop Stackcable is ideal to be used
to distribute a Reset signal to many sequences at once.
Reset is simple. A gate high signal triggers that
particular sequencer to reset back to step one.
Direction works so that with a gate low the sequencer
travels forward. A gate high signal dictates the
sequencer travels backwards.
The Z8000 has a very fast response time and will be
triggerd by long and even very short pulses. The
electrical noise caused by inserting a plug into a
normalized clock input might cause some of the
sequencers to step, this behavior is normal. A
cascaded Reset signal using Stackcables or mults will
reset all sequencers in a group back in line if desired.
The Z8000 inputs are idealy to be used with pulses
but defently are not restricted to pulses only.
LEDs.
The Z8000 uses multicolored LEDs to help with visual
feedback. The red lights are assigned to the eight 4
steps, the green lights are assigned to the two 16
steps & lastly the yellow lights engage when a 4 step
red light & 16 step green light intersect that specific
LED. In addtion to that, when two 4 step sequencer
red lights engage the light intensity of that led
increases by about 35%.
Whether the sequencer is clocked or not, its knobs
and lights are still on and functioning. (ex: the red led
of step A of sequencer 1 is on, plug the CV1 out and
turn that knob, you will hear that the step is “alive”.
+
RESET DIRECTION CLOC K
RESET DIRECTION CLOC K
Z8 0 00 M at r ix S eq u en ce r/ P ro gr am me r
1
2
3
4
A
B
C
D
+
A
1
2
3
4
B C D
CVA CVB CVC CVD
DIR
CK
RT
Tipt p
A u d i o
+
CV1
CV2
CV3
CV4
DIR
CK
RT
+
Applications.
The Z8000 is very simple to use but can create some
extremely complex control patterns. Each sequencer can
be made to step very slow or very fast up to audio
rate. Each CV output has the capability to drive many
inputs. One of the fun applications with the Z8000 is to
patch one of the sequencer’s CV out back to the clock
frequency input, creating a “swing” in the movement
from step to step. The Z8000 has 10 CV outputs that
can modulate 10 prameters in your modular, having
them change polyrhythimcally, making things move.
Although the word ‘sequencer’ is mostly known
as playing a sequence of tones (controlling the pitch
of a VCO), the Z8000 is by no means restricted to
doing only that. The Z8000 is a note sequencer but
also a modulation sequencer and a programmer of
events that happen in a predetermined time.
The Z8000 modular structure makes it interesting
to combine with various clock modifiers such as
Clock dividers, Clock sequencers, etc.
The Z8000 will work well with Quantizers to create
melodies within a scale and analog switches
to route the CV outs to diffrent destinations on your
system.
Trigger delays or EGs can be used to phase the clock
signal and are very useful in creating a “laid back”,
off the grid groove or feel.
We hope you will enjoy your Z8000.
TM
Loading...