Timex W111 User Manual
Please read instructions carefully to understand how to operate your Reebok® watch.
Your model may not have all of the features described in this booklet.
THANK YOU FOR PURCHASING YOUR REEBOK® WATCH.
TIME
To set the time:
1. PULL crown out to “C” position.
2. TURN crown either way to correct time.
3. PUSH crown in to “A” position.
To adjust to a new time zone:
1. PULL crown out to “B” position.
2. TURN crown either way to move the hour hand in hour increments.
BASIC OPERATIONS
• 6 o’clock eye shows seconds.
• 10 o’clock eye shows “minutes elapsed” for chronograph.
• 2 o’clock eye shows “1/20 seconds elapsed” for chronograph.
• Chronograph second hand shows “seconds elapsed” for chronograph.
CALENDAR
To set the calendar:
1. PULL crown out to “B” position.
2. TURN crown either way to move hour hand. Two complete revolutions relative to the 12
o’clock position will move the date forward or backward. This will correct both date and 24hour time.
3. PUSH crown in to “A” position.
NOTE: The date changes automatically every 24 hours.
CHRONOGRAPH
SECOND
CHRONOGRAPH
1/20 SECOND
CHRONOGRAPH
MINUTE
HOUR
SECOND
PUSHER “A”
CROWN POSITION
D A B C
PUSHER “B”
DATE
MINUTE
➧
W-111 921-095007
CHRONOGRAPH
The chronograph is capable of measuring:
• 1/20 seconds elapsed up to 1 second (2 o’clock eye).
• Seconds elapsed up to 1 minute (chronograph second hand).
• Minutes elapsed up to 30 minutes (10 o’clock eye).
NOTE: Chronograph will operate continuously for 4 hours, after which it will automatically
stop and reset.
BEFORE USING THE CHRONOGRAPH,adjust all the chronograph hands to the “0” or 12-hour
positions.
To adjust chronograph hands:
1. PULL crown out to “B” position.
2. PRESS pusher “B” until the hand at the 10 o’clock eye resets to the “30” position.
3. PULL crown out to “C” position.
4. PRESS pusher “A” until the chronograph second hand resets to the “0” or “60” or 12-hour
position.
5. PRESS pusher “B” until the hand at the 2 o’clock eye resets to the “0” position.
6. PUSH in Crown to “A” position.
NOTE:
• Make sure the chronograph is stopped and reset before adjusting.
• PRESSING and HOLDING either pusher “A” or “B” for 2 seconds will cause the hands to move
continuously until the pusher is released.
Standard chronograph measurement:
1. PRESS pusher “A” to start timing.
2. PRESS pusher “A” to stop timing.
3. PRESS pusher “B” to reset.
Split Time Measurement:
1. PRESS pusher “A” to start timing.
2. PRESS pusher “B” to split.
3. PRESS pusher “B” to resume timing.
4. PRESS pusher “A” to stop timing.
5. PRESS pusher “B” to reset.
INDIGLO® NIGHT-LIGHT
With the crown in the “A” position, PUSH crown to the “D” position. Entire dial will be illuminated.
Patented (U.S. pat 4,527,096 and 4,775,964) electroluminescent technology used in INDIGLO®
night-light illuminates entire watch face at night and in low light conditions.
NIGHT-MODE® FEATURE
To use NIGHT-MODE® feature:
1. PUSH and HOLD Crown to “D” position for 4 seconds to activate NIGHT-MODE® feature
(U.S. pat. 4,912,688). PRESSING any pusher will cause the INDIGLO® night-light to stay on for
3 seconds.
2. NIGHT-MODE® feature will last for 8 hours.
3. Or PUSH and HOLD Crown to “D” position for 4 seconds to deactivate NIGHT-MODE® feature.
If your watch is water-resistant, meter marking or ( ) is indicated.
Water-Resistance Depth p.s.i.a.* Water Pressure Below Surface
30m/98ft 60
50m/164ft 86
100m/328ft 160
*pounds per square inch absolute
WATER RESISTANCE
WARNING: TO MAINTAIN WATER-RESISTANCE, DO NOT PRESS ANY BUTTONS UNDER WATER.
1. Watch is water-resistant only as long as lens, push buttons and case remain intact.
2. Watch is not a diver watch and should not be used for diving.
3. Rinse watch with fresh water after exposure to salt water.
Loading...