Page 1
Installation Guide
©
2018 Timetec Cloud Sdn Bhd. All rights reserved • 062018
www.timetecsecurity.com
TimeTec BLE-16
Smart Lift Controller
RECOMMENDATIONS:
•
Install the device inside a lift car, near to the floor button controller to
minimize the need of extra wiring.
•
Install an on/off switch to turn off the power supply to the device.
Power off to bypass the device, and the floor access function will be
back to default operation, where user can press button at the lift
button panel to access its desired floors.
•
For a building with more than 16 floors, the installation requires more
than one BLE16 relay boards. For example, a building with 30 floors
will need 2 units of BLE 16 relay boards, where the first relay board will
control access from Floor 1 to Floor 16, and the second relay board
will control the access from Floor 17 onwards until Floor 30.
Below is a list of accessories that are necessary to install
TimeTec BLE-16
PW12V Switching Power Supply
AC/DC switching power supply to keep the
battery charged during daily operation
and also allows it to function during a
power failure as well.
TimeTec BLE-16
STEP • 2
Make sure
that you have
all the required
accessories
for the
installation
STEP • 1
Determine
where you
want to install
TimeTec
BLE-16
The User Guide for TimeTec Security App can be
obtained in the App or in our website at
www.timetecsecurity.com
iOS Android
Floor button
control panel
LIFT
123
456
789
10 11 12
TimeTec Lift
Control Panel
BLE-16
Page 2
Follow the diagram below to wire up TimeTec BLE - 16
to lift button controller and its accessories
STEP
1) Connect the 12V DC 3A power source to the power
input port of TimeTec BLE-16. DO NOT
2) SWITCH ON the power until all the wiring work is
done.
3) Connect relay output of button 1 (from Lift button
panel) to BLE-16 CH-1 relay input port.
Connect CH-1 relay output (from BLE-16) to 1st
Floor Relay in Floor Control Panel. Repeat step 2
and 3 for all buttons and oors. We recommend
that you keep all buttons for Ground oor, open
lift door and close door, to connect directly to the
Floor control panel.
4) Turn on the power to the lift car and all components.
5) Sign in to TimeTec Security mobile app to
complete the setup.
FIRST CHECK
•
The Bluetooth chipset (mark 1) is lit up and
blinking.
•
The LED of each input/output is lit up
SECOND CHECK
•
Install TimeTec Security mobile app and scan
the TimeTec BLE - 16 serial number under Add
Access section.
STEP • 3
Get ready to install
STEP • 4
Checking the progress
of installation
If any of the above is not
working as expected please
check the wiring or contact
support@timeteccloud.com
for advise.
This guide is prepared in
English language, for other
languages, please refer to
the website.
Register for
product warranty
in TimeTec
Security App.
Close Door RelayGround Floor Relay
9th Floor Relay
1rd Floor Relay
10th Floor Relay
2rd Floor Relay
11th Floor Relay3rd Floor Relay
12th Floor Relay
4th Floor Relay
13th Floor Relay
5th Floor Relay
14th Floor Relay6th Floor Relay
15th Floor Relay
7th Floor Relay
16th Floor Relay
8th Floor Relay
Open Door Relay
Floor Control Panel
8
7
6
5
4
3
2
1
16
15
14
13
12
11
10
9
G
OPEN
CLOSE
Lift Button Panel
+
_
12CDC_IN
+
_
12VDC
Power
Supply
A
C
B
B
INPUT
OUTPUT
CH -1
BLE-16 Relay Board
FUNCTIONS
The power input port. Use 12V
DC 3A power supply to power
up the BLE-16.
The input and output slots to
connect to the lift button
panel and the oor control
panel. Each channel is for one
oor only.
Input to connect to individual
button at the lift button panel.
Output to connect to the
individual relay at the oor
control panel.
The Bluetooth receptor to
receive command from mobile
app and Bluetooth cards.
B
C
A
Loading...