Time Module VD33, VD34 Technical Manual & Parts Catalogue

Revised on : 23. Jun. 2017

SII Products

ANALOGUE QUARTZ

TECHNICAL GUIDE

&

PARTS CATALOGUE

Cal.VD33&VD34

[SPECIFICATION]

*Cal VD34

・・・

・・・・・・

・・・

Cal.VD33 without calendar

3 Hands ( Hour , Minute , Second )
Dual time of 12 hour regulator hand
Dual time of 60 minute regulator hand
24 hour hand , Calendar (Cal.VD33 only)
Two pole stepping motor
Step motor 2 pieces
Electronic circuit reset switch
Second setting device
Date setting (Cal.VD33 only)
Time difference correction
[ Time ]

Indicated by Hour , Minute , Second and 24 hour hands
Dual time of 12 hour regulator and dual time of 60 minute regulator hands

[ Dual time of 12 hour regulator and dual time of 60 minute regulator ]

±1hour / push

SR920SW (Silver oxide battery)
Battery life is approximately 2 years
Use 10-second gate
*Set the winding stem with crown at the normal position
0 Jewel

Cal.

PARTS CATALOGUE / TECHNICAL GUIDE

Cal. No.

Item

Cal.VD33&VD34

Version-01

VD33&VD34

Time indication

Outside diameter

Driving　System

Casing diameter

φ 29.50 mm × 26.00 mm (3H-9H)

Cal.VD33...4.57 mm
Cal.VD34…3.97 mm

φ 28.80 mm

Total height

Free

Movement

Movement

size

1

SII Products

Less than ± 20seconds : Monthly rate at normal temperature range

≧

1600A/m

Jewels

Measuring gate by

quartz tester

Battery

Accuracy

First
click

Left rotation
Right rotation

-1hour/push Time difference correction

Additional mechanism

+1hour/push Time difference correction

-

Buttons

Antimagnetic

Button B

VD33 VD34

Free
Free

Date setting

Time setting with stop-second device

Time setting with stop-second device

Normal position

Crown
position

Button A

Second click

0012 079

0808 368 …Cal.VD33 only Auxiliary train wheel bridge screw
Date dial guard

Date dial …Cal.VD33 only
Refer to page 5 for each parts code

Auxiliary train wheel bridge

Refer to page 5 for each parts code

0806 368 …Cal.VD33 only
Date corrector wheel

0810 368 …Cal.VD33 only

Date jumper

Small hour hand wheel

Refer to page 5 for each parts code

0737 891 …Cal.VD33 only

Refer to page 5 for each parts code

0836 369 …Cal.VD33 only

0886 003 Intermediate wheel for date
Intermediate 12 hours wheel corrector holder
and pinion (B)

0962 891 …Cal.VD33 only

12 hours wheel
Refer to page 5 for
each parts code 0962 891 …Cal.VD33 only

0886 001
Intermediate 12 hours
wheel and pinion (A)

0885 002

Hour wheel
Refer to page 5 for
each parts code

Small minute wheel
Refer to page 5 for
each parts code

PARTS CATALOGUE

Version-02

VD33&VD34

①

Intermediate wheel for date corrector (D)

⑦

⑧

②

③

④

⑤

⑥

SII Products

⑩

Intermediate small minute wheel

⑫

Intermediate wheel for date corrector (B)

2

Intermediate wheel for date corrector (C)

⑰

⑱

⑬

⑭

⑮

⑯

⑨

⑪

Type of oil Oil quantity mark

Moebius 9010 NORMAL QUANTITY
Moebius 9030 SUFFICIENT QUANTITY

Disassembling procedures Figs.

㊺

⇒

①

Reassembling procedures Figs.

①

⇒

㊺

Battery

Winding stem

Cal.VD33 …0351 177
0012 079 Cal.VD34 …0351 178
Switch spring screw

0012 079

Switch spring screw

Switch spring
Cal.VD33 …4250 332
Cal.VD34 …4250 342

4004 331

Circuit block

0012 079
Train wheel bridge (B) screw

0125 331 4270 358
Train wheel bridge (B) Battery connection (-)

4146 177
Step rotor (B)

4002 923
Coil block (B)

4239 357
Rotor stator (B)

0701 014
Fifth wheel and pinion (B)

*All parts code are subject to changewithout notice.

PARTS CATALOGUE

Version-04

VD33&VD34

⑲

⑳

SII Products

3

㉚

㉑

㉑

㉒

㉓

㉔

㉕

㉖

㉗

㉘

㉙

Type of oil Oil quantity ma rk

Moebius 9010 NORMAL QUANTITY
Moebius 9030 SUFFICIENT QUANTITY