Timeguard LEDX30PIRB User Manual

30W LED PIR
FLOODLIGHT

Model: LEDX30PIRB

Model: LEDX30PIRWH

1. Designated Use

1

8

0

1.8 TO 2.5 METER

12 METER

3 METER

1

8

0

1.8 TO 2.5 METER

12 METER

3 METER

1

8

0

1.8 TO 2.5 METER

12 METER

3 METER

• LEDX30PIR is an outdoor motion detector for automatic LED lighting
control.

• Mainly for wall installation.

• Simple plug in wall plate for easy & safe connection

• Suitable for a wide range of locations: corridors, gardens, staircases,

entrances, garages, outdoor parking areas etc.

WARNING

2. Basic Safety Instruction

Danger of death through electric shock.

• Must only be installed by qualifi ed electricians.

• Avoid the metal parts of the device due to potentially high temperature.

• Conforms to the latest EC directives.

1

• Designed for use in normal environments

• Intended for outdoor installation.

• Energy saving.

• Long LED lamp life time.

Index :

Page 2 Contents and Tools required

Page 3 Connection and Installation procedure

Page 4 Installation procedure

Page 5 Sensor detection range

Page 6 Walk test & adjustment, Detector head adjustment

Page 7 Knob settings

Page 8 Lens masking

Page 9 Lamp adjustment and Warning

Page 10 Technical Specifications

1

8

0

1.8 TO 2.5 METER

12 METER

3 METER

1

8

0

1.8 TO 2.5 METER

12 METER

3 METER

1

8

0

1.8 TO 2.5 METER

12 METER

3 METER

3. Contents:

What’s in the box?

Screw:

M4x32mm

X 1

INSTRUCTIONS

MANUAL

2 3

X 1

X 1

X 1

X 2 X 2

X 2 X 4

Screw peg:

6x30mm

Screw:

M3x12mm

Product’s weight:
LEDX30PIR : 1kg

4. Tools required:

Tools / Equipment need for installation.

Flat blade screw driver Suitable for screw head Drill bit with diameter 6mm

X 1

X 1

X 1

1

8

0

1.8 TO 2.5 METER

12 METER

3 METER

1

8

0

1.8 TO 2.5 METER

12 METER

3 METER

1

8

0

1.8 TO 2.5 METER

12 METER

3 METER

5. Connection:

Master-Slave connection

Connect the cable to the terminal block as follows (see connection diagram):
Ensure the connections are secure. Refit wall plate ensuring it clicks

firmly into place.

BROWN

LIVE

BROWN

LIVE

NEUTRAL

EARTH

GREEN / YELLOW

BLUE

Max. wire
1 x 2.5mm per way

Load

Max. wire
2 x 1.5mm per way

Mains
Supply

Isolation

Switch

E
N
L

Switch off the electricity at the fuse box by removing the relevant fuse or

switching off the circuit breaker before proceeding with the installation.

6. Installation Procedure:

1

Switch off the power.

230V

3

Drill and push the screw
peg into the hole.

φ

6mm

*** IMPORTANT ***

2

Marking the screw hole.

4

Fix the U bracket to the wall.

Mounting Screws: (M4 x 32) x 2

1

8

0

1.8 TO 2.5 METER

12 METER

3 METER

1

8

0

1.8 TO 2.5 METER

12 METER

3 METER

1

8

0

1.8 TO 2.5 METER

12 METER

3 METER

5

First, feed the cable through the
rubber gasket of the junction box.

6

Attach the strain relief to the
device and screw in.

4

EARTH

7

Tighten the screws.

Connect the individual wires to the appropriate terminal then tighten

9

Loosen the screws.

8

the screws.

10

Attach the
wallplate
to the device.

11

Attach the device to the U
bracket then tighten the
screws on both sides.

Screw: M3x12mm x 4

CONNECTION

( See connection diagram )
Connect the mains supply cable to the
terminal block on the backplate as follows.

Connect the cable from the lighting load to the

terminal block on the backplate as follows.

LIVE

NEUTRAL

EARTH

LIVE

NEUTRAL

EARTH

12

Connect device
to the mains.
Unit goes into
warm-up period
for 40 sec.

Push

“click”

BROWN

BLUE

GREEN / YELLOW

BROWN

BLUE

GREEN / YELLOW

1

8

0

1.8 TO 2.5 METER

12 METER

3 METER

1

8

0

1.8 TO 2.5 METER

12 METER

3 METER

1

8

0

1.8 TO 2.5 METER

12 METER

3 METER

Installation Advise:

WARNING

As the detector reacts to variations in temperature, avoid situations:

• Do not direct motion detectors at objects with highly-reflective surface

such as mirrors etc.

• Do not install motion detectors near heat sources such as heating outlets,

air conditioning system, lamps etc.

• Do not direct the motion detector at objects that move in the wind such

as curtains, large plants etc.

• Take account of motion direction during test run.

5

40

30

20

10

40

40

30

20

10

40

Detection Range:

LEDX30PIR:
Recommended installation height is 2.5 meter above
ground, the maximum detection range about 12 meter and at the angle
of about 180 deg.

up to12m

2.5 METER

3 METER

12 METER

0

8

1

40

30

20

10

40

3m

180°

180°

Walk Test and Adjustment

The purpose of Walk Test is used to test and adjust the detection coverage of

LEDX30PIR under auto mode.

• Adjust the Time knob to minimum (fully anti-clockwise), then conduct a
walk test as described in test procedure.

Test procedure:

• Adjust the Time knob to (fully anti-clockwise), (Lux knob can be “Sun” or
“Moon”).

• Switch power on.

• Walk across the detection area, once the detector is triggered and the lamp

will turn ON for 2 seconds.

Note walking direction when performing test.

Dusk Time

6

Test mode

Detector Head Adjustment

The detector head can be 90º turned left or right by hand and can be tilted

90º downward .

* Do not use the adjuster knobs to turn

the detector head.

2 sec

0

2

Sec

Pan left 90º

Tilt down 90º

Pan right 90º

Knob Settings

LEDX30PIR has two adjustment knobs:
Time and Lux at the bottom of the detector head.

• Adjust knobs carefully with flat blade screwdriver.

TIME knob setting

• You can set the time knob from 5 sec to about 10 min, LEDX30PIR will
turn ON the lamp, for the time duration set after each detected movement.

• Adjust the knob as desired.

LUX knob setting

• When setting the Lux knob at “MOON”, LEDX30PIR will only operate

in the dark.

• When setting the Lux knob at “SUN”, LEDX30PIR will operate in any
light level.

Adjustments

7 8

Dusk/Dawn

Environment lux level to turn On

Test mode

Turn On time adjustment

Time

10min5sec

0

5

sec

Dusk Setting (Time knob setting)

• When setting the Time knob to fully clock wise, the motion detector of
LEDX30PIR won’t function.

The lamp will operate depending on the “LUX” level, ie Dusk to Dawn..

0

Min

10

Lamp turns

ON at night.

Lamp turns ON
at day & night.

Setting Advise

WARNING

Lens masking

The purpose of the lens mask is to mask out areas not desired for detection.

Masking The Sensor Lens:

• To restrict the sensor coverage, preventing detection in unwanted areas,
mask the sensor lens using the masking label provided. The top section of
the lens covers long range detection, the bottom covers short range.
Similarly the left and right lens sections cover the left and right detection
areas respectively.

Manual Override Mode:

The light can be switched on for longer time periods by use of the Manual
Override Mode.
This can be activated at night by using the internal wall switch or circuit
breaker.

Switch the internal wall switch/circuit breaker single (OFF/ON) within 1
second.
The unit will now illuminate continuously until dawn or until switched back
into Auto Mode.

To switch the unit back into Auto Mode, switch the internal wall switch/circuit
breaker once (OFF/ON) within one second.
The unit will return to its Auto mode and will operate as set up after the walk
test procedure.

Lamp Adjustment

The lamp can be tilted upward 45º and

tilted downward 60º.

9

WARNING

This product will get warm when in
normal use. Can be installed on
surfaces of normal flammability
e.g. wood, plasterboard, brickwork
and other masonry. Do not install
on flammable surfaces such as
plastics.

Tilt upward 45º

Tilt downward 60º

60
50
40

+40

30
20

-20

10

Technical specifications:

Energy Usage Lamp On
Power Supply
Power Factor
Colour Temperature
Colour Rendering
Lumen Output initial
Lamp Beam Angle

Detection Range
Detection Angle
Time On Adjustment
Dusk Level Adjustment
Environmental Protection
EC Directives

Slave Output:

LEDX30FL
LED lamp
Halogen lamp
CFL
Fluorescent tube w/o PF correction

28kWh/1000h: 27.5W typ
230 V
> 0.95
5000 - 5600K
> 70
Black: 2115 Im typ, White: 2310 lm typ
110 x 100 degrees
The lamps are not replaceable in this product
Up to 12 metres
180º
5 seconds - 10 minutes
Day & night or night only operation
IP55 (suitable for indoor and outdoor use)
Conforms to current EC Directives

Energy Efficiency Class A+

AC ~ 50Hz

Max. 10 sets
Max. 10 sets with total 200W
Max. 1000W
Max. 15 sets 23W or Max. 345W
Max. 648W

10

If you experience problems refer to Troubleshooting Guide.

If problems still exist, do not immediately return the unit to store.

Telephone the Timeguard Customer Helpline

Qualified Customer Support Co-ordinators will be on-line to assist

020 8450 0515

in resolving your query.

3 Year Guarantee

In the unlikely event of this product becoming faulty due

to defective material or manufacture within 3 years of the

date of purchase, please return it to your supplier in the

first year with proof of purchase and it will be replaced free

of charge. For years 2 and 3 or any difficulty in the first year telephone

the helpline on 020 8450 0515.

Note:

A proof of purchase is required in all cases. For all eligible replacements
(where agreed by Timeguard) the customer is responsible for all
shipping/postage charges outside of the UK. All shipping costs are to be
paid in advance before a replacement is sent.

HELPLINE

020 8450 0515

or email [e-mail]

For a product brochure please contact:

Timeguard Limited.

Victory Park, 400 Edgware Road,

London NW2 6ND

Sales Offi ce: 020 8452 1112

or email csc@ timeguard.com

67.058.503 (Iss.2)