Page 1
LED Wide Beam Floodlight
Model: LEDX20FLBN (Black)
Model: LEDX20FLWHN (White)
I n s t allat ion & O perating Instruction s
Model: LEDX10FLBN (Black)
Model: LEDX10FLWHN (White)
Model: LEDX30FLBN (Black)
Model: LEDX30FLWHN (White)
Page 2
1
1. General Information
These instructions should be read carefully and retained for further reference
and maintenance.
2. Safety
• Before installation or maintenance, ensure the mains supply to the luminaire
is switched off and the circuit supply fuses are removed or the circuit breaker
turned off.
• It is recommended that a qualified electrician is consulted or used for
the installation of this luminaire and install in accordance with the
current IEE wiring and Building Regulations.
• Check that the total load on the circuit including when this luminaire is fitted
does not exceed the rating of the circuit cable, fuse or circuit breaker.
3. Technical Specifications
• 230V AC, 50Hz
• These luminaires are of class I construction and must be earthed
• Colour Temperature: 4000K
• Energy Efficiency: Class E
• IP55 Rated suitable for restricted external applications
• CE Compliant
LEDX10FLBN-WHN
• 10W LED Non replaceable lamp
• Energy Usage: 12Kwh/1000h
• Lumen Output: 1000lm
LEDX20FLBN-WHN
• 20W LED Non replaceable lamp
• Energy Usage: 21Kwh/1000h
• Lumen Output: 2000lm
LEDX30FLBN-WHN
• 30W LED Non replaceable lamp
• Energy Usage: 32Kwh/1000h
• Lumen Output: 3000lm
Page 3
2
4. Installation
4.1 Mark the position of the mounting holes
on the wall using the U bracket supplied
as a template.
4.2 Drill the holes for the wall plugs ensuring
not to infringe with any gas/water pipes
or electrical cables that may be hidden
below the surface.
4.3 Fix the U bracket to the wall using
the correct screws for the wall
plugs installed.
4.4 Secure the supply cable into the junction box through the hole(s) provided
ensuring that a cable gland, grommet or sealing compound is used
to maintain the IP rating of the luminaire.
Page 4
3
4.5 Attach the strain relief to the luminaire
and screw in ensuring not to over-tighten.
4.6 Terminate the supply cable into the terminal
block (please refer to section 5 connection
diagram) ensuring correct polarity is observed
and that all bare conductors are sleeved.
4.7 Attach the supplied wall plate to the luminaire,
apply pressure to catches located on top and
bottom until all click into place to ensure the
weatherproof seal.
4.8 Attach the luminaire to the U bracket
fitted to the wall, then screw in on both
sides ensuring not to over-tighten.
Page 5
L N
MAINS
SUPPL
E
5. Connection Diagram
ISOLATION
SWITCH
L
4
Y
Connect the 3 core mains supply cable to the block on the unit as follows:-
LIVE (Brown or Red) L
NEUTRAL (Blue or Black) N
EARTH (Green/Yellow)
N
Page 6
5
6. Operation
• Turn the power on to the isolating switch and test for correct operation.
7. Lamp Adjustment
• The lamp can be tilted upwards 45° and tilted downwards 60°.
Page 7
6
3 Year Guarantee
In the unlikely event of this product becoming faulty due to defective material
or manufacture within 3 years of the date of purchase, please return it to your
supplier in the first year with proof of purchase and it will be replaced free
of charge. For years 2 and 3 or any difficulty in the first year, telephone the helpline
on 020 8450 0515.
Note: A proof of purchase is required in all cases. For all eligible replacements
(where agreed by Timeguard) the customer is responsible for all shipping/postage
charges outside of the UK. All shipping costs are to be paid in advance before
a replacement is sent.
Page 8
If you experience problems, do not immediately return the unit
to the store. Telephone the Timeguard Customer Helpline:
HELPLINE
020 8450 0515
or email helpline@timeguard.com
Qualified Customer Support Coordinators will be online
to assist in resolving your query.
For a product brochure please contact:
Timeguard Limited.
Victory Park, 400 Edgware Road,
London NW2 6ND
Sales Office: 020 8452 1112
or email csc@timeguard.com
TW - August 2021
www.timeguard.com
67.058.648 (Issue 3)
Loading...