Timeguard LEDSF10B, LEDSF10WH, LEDSF20B, LEDSF20WH, LEDSF30B Installation & Operating Instruction

Installation & Operating Instructions

Slimline LED Floodlights

Model: LEDSF10B – Black

Model: LEDSF10WH – White

Model: LEDSF20B – Black

Model: LEDSF20WH – White

Model: LEDSF30B – Black

Model: LEDSF30WH – White

Model: LEDSF50B – Black

Model: LEDSF50WH – White

1

1. General Information

These instructions should be read carefully and retained for further reference
and maintenance.

2. Safety

• Before installation or maintenance, ensure the mains supply to the luminaire
is switched off and the circuit supply fuses are removed or the circuit breaker
turned off.

• It is recommended that a qualified electrician is consulted or used for
the installation of this luminaire and install in accordance with the current
IEE wiring and Building Regulations.

• Check that the total load on the circuit including when this luminaire
is fitted does not exceed the rating of the circuit cable, fuse or circuit breaker.

• This product is not suitable for use in food preparation areas.

3. Technical Specifications

• 230V AC, 50Hz

• These luminaires are of class I construction and must be earthed

• Colour Temperature: 5000K

• Energy efficiency class: A+

• Power Factor: >0.5

• Pre Fitted Cable Length: 1 metre

• Operating Temperature: -20°C to +40°C

• IP65 Rated suitable for restricted external applications

• CE Compliant

• EC Directives: Conforms to latest directives

2

LEDSF10B-WH

• 10W LED Non replaceable lamp

• Energy Usage: 10kWh/1000h

• Lumen Output: 800lm

• Allen key size for bracket: 4mm (not supplied)

• Dimensions (H x W x D): 117 x 155 x 30mm

LEDSF20B-WH

• 20W LED Non replaceable lamp

• Energy Usage: 20kWh/1000h

• Lumen Output: 1750lm

• Allen key size for bracket: 4mm (not supplied)

• Dimensions (H x W x D): 158 x 205 x 33mm

LEDSF30B-WH

• 30W LED Non replaceable lamp

• Energy Usage: 30kWh/1000h

• Lumen Output: 2550lm

• Allen key size for bracket: 5mm (not supplied)

• Dimensions (H x W x D): 197 x 265 x 36mm

LEDSF50B-WH

• 50W LED Non replaceable lamp

• Energy Usage: 50kWh/1000h

• Lumen Output: 4200lm

• Allen key size for bracket: 5mm (not supplied)

• Dimensions (H x W x D): 252 x 335 x 39mm

3

4. Installation

• Ensure the mains supply is switched off and the circuit supply fuses
are removed or the circuit breaker turned off.

• An isolating switch should be installed to the switch the power
ON and OFF to the luminaire. This allows the unit to be easily
switched OFF for maintenance purposes.

• Remove the mounting bracket by undoing the two bolts and washers
located on the left and right side of the luminaire (take note of the order
of the washers).

• Use the mounting bracket as a template and mark the position
of the mounting holes on the wall.

• Drill the holes for the wall plugs ensuring not to infringe with any
gas/water pipes or electrical cables that may be hidden below the surface.
Insert the wall plugs.

• Fix the mounting bracket to the wall using the correct screws
for the wall plugs installed.

• Re-attach the luminaire to the mounting bracket using the two bolts
and washers previously removed, just enough to secure into place
but do not over tighten.

• 1 metre of cable is supplied with the product pre fitted via a waterproof
cable gland. Connect the supplied wire to the terminals in a junction box
with the required IP rating, and connect the incoming mains to the terminals
in the junction box ensuring correct polarity is observed and that all bare
conductors are sleeved (see section 5. Wiring Connections).

Note: If a junction box is not being used, pass the 1 metre supplied cable

through your pre drilled hole (if required), then connect directly to the
isolation switch.

• Adjust the angle of the luminaire so it illuminates the required area
and then tighten the bolts holding the bracket to the luminaire body.

4

3 Year Guarantee

In the unlikely event of this product becoming faulty due to defective material or
manufacture within 3 years of the date of purchase, please return it to your supplier
in the first year with proof of purchase and it will be replaced free of charge.
For years 2 and 3 or any difficulty in the first year, telephone the helpline
on 020 8450 0515.

Note: A proof of purchase is required in all cases. For all eligible replacements
(where agreed by Timeguard) the customer is responsible for all shipping/postage
charges outside of the UK. All shipping costs are to be paid in advance before
a replacement is sent.

Live (Brown) L

Neutral (Blue) N

Earth (Green/Yellow)

5. Wiring Connections

• The 1 metre supplied cable is 1.0mm² 3 core flex.

Zerofour – April 2016

67.058.553 (Issue 1)

Timeguard Limited.

Victory Park, 400 Edgware Road,

London NW2 6ND

Sales Office: 020 8452 1112

or email [e-mail]

For a product brochure please contact:

If you experience problems, do not immediately return the unit

to the store. Telephone the Timeguard Customer Helpline;

Qualified Customer Support Co-ordinators will be on-line

to assist in resolving your query.

HELPLINE

020 8450 0515

or email helpline

@

timeguard.com

www.timeguard.com