Timeguard LEDPROSLWH, LEDPROSLB Installation Instructions

Dedicated PIR Professional

LEDPROSLB & LEDPROSLWH

I nst a l la ti o n & O p e ra t i ng In st ru ct i o n sI nst a l la ti o n & O p e ra t i ng In st ru ct i o n s

Ins t allation & O pera ting In s t r u c t ions

1. General Information

These instructions should be read carefully and retained for further reference and

maintenance.

2. Safety

off.

3. Technical Specications

1

Dimensions

78

108

114

12

TOP VIEW

SIDE VIEW

180°

A

B

Less

sensitive

Dusk Level

Adjust

Lens Sticker

C

Delay Time

Adjust

D

More

sensitive

Restrict Long

Detection

Restrict RHS

Detection

Restrict short

Detection

Restrict LHS

Detection

E

3

Note:

Mains

Supply

Isolation

Switch

'Switch Live'

F

4

4. Selecting The Location

angles as shown (see diagram A).

to maintain coverage and forward coverage will be reduced.

diagram A detailing detection range and direction.

may cause false activation under extreme conditions.

During extreme weather conditions the motion sensor may exhibit unusual behaviour. This

5. Installation

G

*** IMPORTANT ***

Switch o the electricity at the fuse box by removing the

relevant fuse or switching o the circuit breaker

before proceeding with the installation.

Jumper Plug

Locking bar

5

CONNECTION

Connect the mains supply cable to the terminal block on the back plate as follows
(see connection diagram):

EARTH (Green / Yellow)
NEUTRAL (Blue) N
LIVE (Brown) L

Connect the cable from the slave lighting load to the terminal block on the
backplate as follows (see connection diagram):

bar with one

with the other

to reconnect).

EARTH (Green/Yellow)
NEUTRAL (Blue) N
SWITCH LIVE (Brown) L

• Ensure that all connections are secure.

• Connect the 3 way PIR plug, by pushing the plug and socket inside the floodlight together
until they lock. DO NOT FORCE. THE PLUG AND SOCKET WILL ONLY FIT TOGETHER ONE
WAY AROUND (See Jumper Plug diagram).

• Secure the PIR to the luminiare using the 4 fixing screws supplied (see diagram G)

6

6. Commisioning and Operation

Walk Test Procedure

The unit can be set up in daylight or at night.

seconds. This indicates the unit is wired correctly.
The unit is in Automatic Mode when the light turns off.

Setting Up For Automatic Operation

setting between these limits.

each adjustment to try to get the unit to detect as above.

7. Masking The Sensor Lens

sensor lens using the lens mask sticker supplied (see diagram D).

range.
Similarly the left and right lens sections cover the left and right detection area
respectively.

8. Manual Override Mode

17

procedure.

9. Detector Head Adjustment

The detector head can be panned 90˚ to the right and 90˚ to the left.

90˚

90˚

Tilt down

10. Accessing Terminals After Installation

This may be necessary to add further lighting for instance and the following procedure for
removing the unit from its backplate should be followed:­Insert the wire through the hole indicated in diagram F.
The terminals are now accessible. If adding lighting, ensure the unit’s rating is not
exceeded.

If you experience problems refer to Troubleshooting Guide.

If problems still exist,

do not immediately return the unit to store.

Telephone the Timeguard Customer Helpline

020 8450 0515

Qualied Customer Support Co-ordinators will be on-line to

assist in resolving your query.

8

11. Troubleshooting

PROBLEM SOLUTION

night and day.

night, or PIR keeps activation at
random for no apparent reason

terminals may be transposed.

The unit may be suffering from false activation.
Cover the sensor lens completely with black PVC
tape. This will prevent the sensor from “seeing”
anything. If the unit now switches off after the
set time duration and does not re-activate, this
indicates that the problem was cause by false
activation. The problem may be solved by slightly
adjusting the direction/angle of the sensor head
(see previous section). If however, the unit

the unit is faulty and should be replaced.

You may not be allowing the unit time to
complete it’s warm-up period. Stand well out of
the detection range and wait (the warm-up period

Sometimes passages between buildings etc. can
cause a “wind tunnel” effect.
Ensure the unit is not positioned so as to allow
detection of cars/people using public throughfares
adjacent to your property.
Ensure that the unit is mounted securely, even the
slightest movement can result in a false detection.

9

PIR sensor will not operated
at all.

The PIR sensor will not

operate at night.

Unit activates during
the daytime.

PIR coverage is poor/
sporadic.

Detection range varies
from day to day.

breaker/internal wall switch.

UIT

wiring connections as per the diagram (see
diagram E).
Ensure no connections are loose.
Check the bulb. If the bulb has failed, replace (do
not hold bulb directly with fingers, use a tissue or
clean dry cloth).
Ensure that the bulb is seated correctly in the
bulbholder.

Refer to section 4 for DUSK control adjustment.

Refer to section 4 for DUSK control adjustment.

Unit may be poorly located. See previous
section-“Selecting The Location” and re-locate
the unit.

PIR sensors are influenced by climatic conditioins.
The colder the ambient temperature, the more
effective the sensor will be. You may need to
make seasonal adjustments to the sensor head
position to ensure trouble-free operation all year
round.

10

3 Year Guarantee

In the unlikely event of this product becoming faulty due to defective material or
manufacture within 3 years of the date of purchase, please return it to your supplier
in the first year with proof of purchase and it will be replaced free of charge.

For years 2 and 3 or any difficulty in the first year, telephone the helpline on
020 8450 0515 .

agreed by Timeguard) the customer is responsible for all shipping/postage charges

is sent.

If you experience problems, do not immediately return the unit

to the store. Telephone the Timeguard Customer Helpline;

HELPLINE

020 8450 0515

or email helpline@timeguard. com

Qualied Customer Support Co-ordinators will be on-line

to assist in resolving your query.

For a product brochure please contact:

Timeguard Limited.

Victory Park, 400 Edgware Road,

London NW2 6ND

Sales Offi ce: 020 8452 1112

or email [e-mail]

www.timeguard.com

67.058.563 (issue 3)