Timeguard LEDPRO100WH, LEDPRO70B, LEDPRO100B Installation Instructions

Rewireable Floodlight

LEDPRO100B

Black

LEDPRO100WH

White

I n s t allat ion & O perating Instruction s

Professional

LEDPRO70B

Black

LEDPRO70WH

White

1

1

1. General Information

These instructions should be read carefully in full before installation and retained
for further reference and maintenance.

2. Safety

• Before installation or maintenance, ensure the mains supply to the floodlight
is switched off and the circuit supply fuses are removed or the circuit breaker
turned off.

• It is recommended that a qualified electrician is consulted or employed
for the installation of this floodlight and that it is installed in accordance
with current IEE wiring and Building Regulations.

• Check that the total load on the circuit including when this floodlight is fitted
does not exceed the rating of the circuit cable, fuse or circuit breaker.

• DO NOT place any object closer than 1 metre in front of the floodlight.

3. Technical Specifications

• 230V AC 50Hz

• This PIR sensor is of class I construction and must be earthed

• Colour Temperature: 4000K

• Energy Efficiency: Class F

• Operating Temperature: -20°C to +40°C

• IP65 Rated, suitable for restricted external applications

• Dimensions (H x W x D): 235 x 305 x 66mm

• CE Compliant

LEDPRO70B & LEDPRO70WH

• 70W LED Non replaceable lamp

• Energy Usage: 70kWh/1000h

• Lumen Output: Black = 7800lm, White = 7800lm

LEDPRO100B & LEDPRO100WH

• 100W LED Non replaceable lamp

• Energy Usage: 100kWh/1000h

• Lumen Output: Black = 12,000lm, White = 12,000lm

2

1

4. Installation

• Ensure the mains supply is switched off and the circuit supply fuses are removed
or the circuit breaker turned off.

• An isolating switch should be installed to enable the power to be switched
ON and OFF to the floodlight. This allows the unit to be easily switched OFF
for maintenance purposes.

• Mark the position of the mounting holes on the wall using the U bracket
supplied as a template.

• Drill the holes for the wall plugs ensuring not to infringe on any gas/water
pipes or electrical cables that may be hidden below the surface.

3

1

• Fix the U bracket to the wall using the correct screws for the wall plugs being used.
Note: Ensure that when you mount this, the slots at the end of the bracket open
upwards to allow you to easily attach and secure the floodlight when ready.

• Attach the floodlight to the U bracket fitted to the wall. You can pre-fit the
supplied fixing screw/bolt and washers to the floodlight before you do this,
the screws/bolts will just need to be loose enough to fit over the upward-facing
slots at the end of the U bracket. Make sure the washers are in the correct order
as per the diagram. When the floodlight is in place, secure the screws/bolts,
ensuring not to overtighten.

• Pass the supply cable through the holes(s) provided in the backplate ensuring
that a cable gland, grommet or sealing compound is used to maintain the
IP rating of the floodlight.

4

1

• Terminate the supply cable into the terminal block (see section 5.
Connection diagram) ensuring correct polarity is observed and that
all bare conductors are sleeved.

• Attach the backplate to the floodlight, and apply pressure to the top and
bottom, then secure all four fixing screws ensuring not to overtighten.

5

1

5. Connection Diagram

• Connect the 230V 50Hz mains supply cable as follows;

230V 50Hz Mains Supply

Live Supply (Brown or Red) to L
Neutral Supply (Blue or Black) to N
Earth (Green/Yellow) to

Note: the L terminal is a Switch Live “Live Output” for slave floodlights
(when used in conjunction with the Timeguard LEDPROSLB-WH, LEDPRORFKB-WH
PIRs or the LEDPROPCB-WH Photocell).

6

1

6. Operation

• Turn the power ON and test for normal operation.

7.Lamp Adjustment

• The floodlight can be tilted as per the diagram.

3 Year Guarantee

In the unlikely event of this product becoming faulty due to defective material
or manufacture within 3 years of the date of purchase, please return it to your supplier
in the first year with proof of purchase and it will be replaced free of charge. For years
2 and 3 or any difficulty in the first year, telephone the helpline on 020 8450 0515.

Note: A proof of purchase is required in all cases. For all eligible replacements
(where agreed by Timeguard) the customer is responsible for all shipping/postage
charges outside of the UK. All shipping costs are to be paid in advance before
a replacement is sent.

If you experience problems, do not immediately return the unit

to the store. Telephone the Timeguard Customer Helpline:

HELPLINE

020 8450 0515

or email [e-mail]

Qualified Customer Support Coordinators will be online

to assist in resolving your query.

For a product brochure please contact:

Timeguard Limited.

Victory Park, 400 Edgware Road,

London NW2 6ND

Sales Office: 020 8452 1112

or email [e-mail]

TW – December 2022

www.timeguard.com

67-058-637 (Issue 4)