Page 1
Slimline LED Floodlight
Model: LEDPRO10WH (White)
Model: LEDPRO10B (Black)
Installation & Operating Instructions
Model: LEDPRO20WH (White)
Model: LEDPRO20B (Black)
Model: LEDPRO50WH (White)
Model: LEDPRO50B (Black)
Model: LEDPRO30WH (White)
Model: LEDPRO30B (Black)
Page 2
1
1. General Information
These instructions should be read carefully and retained for further reference
and maintenance.
2. Safety
• Before installation or maintenance, ensure the mains supply to the luminaire
is switched off and the circuit supply fuses are removed or the circuit breaker
turned off.
• It is recommended that a qualified electrician is consulted or used for
the installation of this luminaire and install in accordance with the
current IEE wiring and Building Regulations.
• Check that the total load on the circuit including when this luminaire is fitted
does not exceed the rating of the circuit cable, fuse or circuit breaker.
3. Technical Specifications
• 230V AC, 50Hz
• These luminaires are of class I construction and must be earthed
• Colour Temperature: 5000K
• Energy Efficiency: class A
• IP65 Rated suitable for restricted external applications
• CE Compliant
LEDPRO10WH & LEDPRO10B
• 10W LED Non replaceable lamp
• Energy Usage: 10Kwh/1000h
• Lumen Output: Black: 650 lm, White: 750lm
LEDPRO20WH & LEDPRO20B
• 20W LED Non replaceable lamp
• Energy Usage: 20Kwh/1000h
• Lumen Output: Black: 1400lm, White: 1500lm
LEDPRO30WH & LEDPRO30B
• 30W LED Non replaceable lamp
• Energy Usage: 30Kwh/1000h
• Lumen Output: Black: 2050lm, White: 2100lm
Page 3
2
LEDPRO50WH & LEDPRO50B
• 50W LED Non replaceable lamp
• Energy Usage: 50Kwh/1000h
• Lumen Output: Black: 3500lm, White: 3600lm
4. Installation
• Ensure the mains supply is switched off and the
circuit supply fuses are removed or the circuit
breaker turned off.
• An isolating switch should be installed to the
switch the power ON & OFF to the luminaire.
This allows the unit to be easily switched OFF for
maintenance purposes.
• Mark the position of the mounting holes on the
wall using the U bracket supplied as a template.
• Drill the holes for the wall plugs ensuring not to
infringe with any gas/water pipes or electrical
cables that may be hidden below the surface.
* 10W & 20W use 6mm screw peg
* 30W & 50W use 7mm screw peg
• Fix the U bracket to the wall using the
correct screws for the wall plugs installed.
Note: Ensure that when you mount this,
the slots at the end of the bracket open
upwards to allow to you to easily attach
and secure the floodlidght when ready
Ø 6mm or 7mm
• Secure the supply cable into the junction
box through the hole(s) provided ensuring
that a cable gland, grommet or sealing
compound is used to maintain the IP rating
of the luminaire.
Page 4
• Attach the strain relief to the
luminaire and screw in ensuring
not to over-tighten.
• Attach the luminaire to the U bracket fitted
to the wall. You are able to pre-fit the
supplied fixing screws and washers to the
luminaire before you do this, the screws
will just need to be loose enough to fit
over the upward facing slots on the
end of the U bracket. Make sure
the washers are in the correct
order as per the diagram. When
the luminaire is in place, secure the
screws ensuring not over tighten.
3
• Terminate the supply cable into the terminal
block (please refer to section 5 connection
diagram) ensuring correct polarity is
observed and that all bare conductors are
sleeved.
• Attach the supplied wall plate to the
luminaire, apply pressure to catches
located on top and bottom, then screw
in on both sides ensuring not to
over-tighten.
Page 5
5. Connection Diagram
N
N L L1
4
MAINS
E
SUPPLY
Connect the 3 core mains supply cable to the block on the unit as follows:-
LIVE (Brown or Red) L
NEUTRAL (Blue or Black) N
EARTH (Green/Yellow)
Note: the L1 terminal is a Switch Live 'Live Output' for slave floodlights (when
used in conjunction with the Timeguard LEDPROSLB/WH PIR or LEDPROPCB/WH
Photocell)
L
ISOLATION
SWITCH
Switch
Live
Page 6
5
6. Operation
• Turn the power on to the isolating switch and test for correct operation.
7. Lamp Adjustment
• The lamp can be tilted 360º turn through U-Bracket.
360º turn through
U-Bracket
Page 7
6
3 Year Guarantee
In the unlikely event of this product becoming faulty due to defective material or
manufacture within 3 years of the date of purchase, please return it to your
supplier in the first year with proof of purchase and it will be replaced free of
charge. For years 2 and 3 or any difficulty in the first year, telephone the helpline
on 020 8450 0515.
Note: A proof of purchase is required in all cases. For all eligible replacements
(where agreed by Timeguard) the customer is responsible for all shipping/postage
charges outside of the UK. All shipping costs are to be paid in advance before a
replacement is sent.
Page 8
If you experience problems, do not immediately return the unit
to the store. Telephone the Timeguard Customer Helpline;
HELPLINE
020 8450 0515
or email [email protected]
Qualified Customer Support Co-ordinators will be on-line
to assist in resolving your query.
For a product brochure please contact:
Timeguard Limited.
Victory Park, 400 Edgware Road,
London NW2 6ND
Sales Offi ce: 020 8452 1112
or email [email protected]
www.timeguard.com
June 2016
67.058.561 (issue 1)
Loading...