Timeguard LEDCSTSSBRB, LEDCSTSSBRWH Installation Instructions

Pan & Tilt Bracket

Model: LEDCSTSSBRB – Black

Model: LEDCSTSSBRWH – White

Installation & Operating Instructions

1

1. General Information

These instructions cover the installation of the Pan & Tilt bracket for the LEDCST
coastal grade floodlight range as specified below. These instructions should
be read carefully in full before installation, and retained for further reference
and maintenance.

2. Safety

• Be careful with the tools used during installation to prevent accidents
or damage.

• If the product is installed without following the designated method,
the product may be unstable and cause a safety issue.

• It is recommended that a qualified electrician is consulted or used for
the installation of these products and install in accordance with the current
IEE wiring and Building Regulations.

3. Technical Specifications

• For use with models;

LEDCST10B-WH 10W LED Coastal Grade Floodlights
LEDCST20B-WH 20W LED Coastal Grade Floodlights
LEDCST30B-WH 30W LED Coastal Grade Floodlights
LEDCST10PIRB-WH 10W LED Coastal Grade PIR Floodlight
LEDCST20PIRB-WH 20W LED Coastal Grade PIR Floodlight
LEDCST30PIRB-WH 30W LED Coastal Grade PIR Floodlight

• CE Compliant

4. Installation

4.1 Ensure that the mains supply to the circuit breaker is switched off

and the circuit supply fuses are removed or the circuit breaker turned OFF.

Image 1

2

4.2 Mark the position of the mounting holes on the wall using the bracket

as a template.

Image 2

Note: the bracket must be fitted
this way up i.e. with the hand
screw hole at the top

4.3 Drill the holes for the rawl plugs ensuring not to infringe with any

gas/water pipes or electrical cables that may be hidden below the surface.
Insert the rawl plugs.

Image 3

3 4

4.4 Fix the bracket to the wall using the correct mounting screws for the wall

plugs installed. Slot in the U- bracket. Make sure it goes to the bottom.
Screw in the hand screw just enough to secure into place, but do not
over tighten.

Image 4

4.5 Remove the fixing screws and washers from each side of the bracket,

taking note of the order as you remove them.

4.6 Attach the floodlight to the bracket fitted to the wall using the fixing screws

and washers previously removed. Screw in on both sides just enough
to secure into place, but do not overtighten.

Image 5

4

4.7 Adjust the angle of the floodlight (left and right pan as shown in image 6,

up and down tilt where the floodlight is attached to the bracket) so it lights
the required area. Finally tighten the fixing screws and hand screw to secure
the floodlight into position.

Image 6

3 Year Guarantee

In the unlikely event of this product becoming faulty due to defective material or
manufacture within 3 years of the date of purchase, please return it to your supplier
in the first year with proof of purchase and it will be replaced free of charge.
For years 2 and 3 or any difficulty in the first year, telephone the helpline
on 020 8450 0515.

Note: A proof of purchase is required in all cases. For all eligible replacements (where
agreed by Timeguard) the customer is responsible for all shipping/postage charges
outside of the UK. All shipping costs are to be paid in advance before a replacement
is sent.

5 6

6

If you experience problems, do not immediately return the unit

to the store. Telephone the Timeguard Customer Helpline;

HELPLINE

020 8450 0515

or email [e-mail]

Qualified Customer Support Co-ordinators will be on-line

to assist in resolving your query.

For a product brochure please contact:

Timeguard Limited.

Victory Park, 400 Edgware Road,

London NW2 6ND

Sales Office: 020 8452 1112

or email [e-mail]

Zerofour – July 2017

www.timeguard.com

67.058.586 (Issue 1)