Timeguard LED400FLWH, LED400FLB Installation Instructions

Single Spot 32W LED Light

Model: LED400FLWH – White

Model: LED400FLB – Black

Installation & Operating Instructions

1

1. General Information

These instructions should be read carefully and retained for further reference
and maintenance.

2. Safety

• Before installation or maintenance, ensure the mains supply to the luminaire
is switched off and the circuit supply fuses are removed or the circuit breaker
turned off.

• It is recommended that a qualified electrician is consulted or used for
the installation of this luminaire and install in accordance with the
current IEE wiring and Building Regulations.

• Check that the total load on the circuit including when this luminaire is fitted
does not exceed the rating of the circuit cable, fuse or circuit breaker.

3. Technical Specifications

• 220V – 240V AC, 50/60Hz

• This luminaire is of class II construction and must not be earthed

• 32W LED Non replaceable lamp

• Energy efficiency: Class A

• Energy Usage: 32KwH/1000H

• Lumen Output: 1700lm

• Colour Temperature: 5000K – 6300K

• Operating Temperature: -25°C to +45°C

• IP55 Rated suitable for restricted external applications

• CE Approved

2

4. Installation

• Undo the fixing screw located on the bottom
of the luminaire/wall plate.

• Remove the wall plate from the luminaire by
releasing one of the lugs (left or right side)
firmly grip the wall plate with your hand,
from top and bottom and carefully lift away
from the fitting.

• Select a suitable cable entry point either
provided or by drilling into the base ensuring
it will not damage or infringe on any of the
internal components, Mark the position of
the mounting holes on the wall using the spacer
(if required) or the wall plate as a template.

• Drill the holes for the wall plugs ensuring
not to infringe with any gas/water pipes
or electrical cables that may be hidden
below the surface. Pass the supply cable
through provided spacer (if required) and
the wall plate, through the hole(s) provided
ensuring that a cable gland, grommet or
sealing compound is used to maintain
the IP rating of the luminaire.

• Fix the spacer (if required) and wall plate to
the wall, using the correct screws for the
wall plugs installed.

• Terminate the cable into the terminal block
(please see section 5 Connection Diagram)
ensuring correct polarity is observed and that
all bare conductors are sleeved.

• Re-connect the luminaire to the wall plate
ensuring the 2 lugs firmly latch on the left
and right hand side, indicated by a ‘click’.

3 4

• Re-fasten the fixing screw located on
the bottom of the luminaire/wall plate
taking care not to over-tighten.

LN

MAINS
SUPPL

N

TERMINAL

5. Connection Diagram

4

ISOLATION
SWITCH

L

Y

Connect the 2 core mains supply cable to the block on the unit as follows:-

LIVE (Brown or Red) L

NEUTRAL (Blue or Black) N

A ‘Loop Terminal’ is provided should a 3 core cable be used.

6. Operation

• Turn the power on to the isolating switch
and test for correct operation.

LOOP

7. Lamp Adjustment

• The lamp can be tilted down 55° and pan outwardly 50° with the spacer
or 40° without.

5 6

• The lamp can be tilted down 55° and pan outward 90° to the left.

• The lamp can be tilted down
55° and pan outward 90°
to the right.

6

3 Year Guarantee

In the unlikely event of this product becoming faulty due to defective material or
manufacture within 3 years of the date of purchase, please return it to your supplier
in the first year with proof of purchase and it will be replaced free of charge.
For years 2 and 3 or any difficulty in the first year, telephone the helpline
on 020 8450 0515.

Note: A proof of purchase is required in all cases. For all eligible replacements (where
agreed by Timeguard) the customer is responsible for all shipping/postage charges
outside of the UK. All shipping costs are to be paid in advance before a replacement
is sent.

If you experience problems, do not immediately return the unit

to the store. Telephone the Timeguard Customer Helpline;

HELPLINE

020 8450 0515

or email [e-mail]

Qualified Customer Support Co-ordinators will be on-line

to assist in resolving your query.

For a product brochure please contact:

Timeguard Limited.

Victory Park, 400 Edgware Road,

London NW2 6ND

Sales Office: 020 8452 1112

or email [e-mail]

Zerofour – August 2015

www.timeguard.com

Designed in the U.K. 67-058-487 (Issue 3)