Page 1
Twin Spot 8W x2 LED
Lighting With Motion
Detection Sensor
Model: LED200PIRWH - White
Model: LED200PIRB - Black
Installation & Operating Instructions
Page 2
1. Designated Use
• LED200PIR is an outdoor motion detector for automatic LED lighting control
• Suitable for installation on walls
• Simple plug in wall plate for easy & safe connection
• Suitable for a wide range of locations: corridors, gardens, staircases, entrances,
garages, outdoor parking areas etc.
2. Basic Safety Instruction
Danger of death through electric shock.
• Must only be installed by qualifi ed electricians.
• Avoid the metal parts of the device due to potentially high temperature.
• The device conforms to EN60598 for designated installation; IP44 in accordance
1
with EN 60598 and IEC62471 Photo biological safety of lamps and lamp system.
• Designed for use in normal environments
• Intended for outdoor installation.
• Energy saving.
• Long LED bulb life.
Index :
Page 2 Contents, Tools required.
Page 3 Product dimensions.
Page 4 Installation procedure.
Page 5 Sensor detection range .
Page 6 Walk test & adjustment, Detector head adjustment.
Page 7 Knob settings.
Page 8 Lens masking.
Page 9 Lamp adjustment, High temperature in lamp.
Page 3
3. Contents:
Whats in the box?
2
4. Tools Required:
Tools/equipment needed for installation.
x 2
x 2
x 1
x 1
x 1
x 1 x 1 x 1
Page 4
5. Product Dimensions:
183.30
22.00
75.00
3
81.00
165.00
61.50
47.50
Page 5
6. Installation Procedure:
Switch off the power. Twist-open the wall plate.
240V
OFF
Fix the wall plate to the wall.
Ø5mm
60mm
Feed the wires through rubber
4
gasket of the wall plate and attach
to corresponding terminal.
L N
Switch On the power.
ON
240V
LNLIVE BROWN
NEUTRAL
BLUE
GREEN/
EARTH
YELLOW
L N
Mounting Screws x2
Attach the device to the wall plate.
Unit goes into warm-up period for 40 sec.
Page 6
Installation Advise:
As the detector responds to changes in temperature, avoid the following
situation:
• Pointing the detector towards objects with highly refl ective surfaces, such as
mirrors etc.
• Mounting the detector near heat sources, such as heating vents, air conditioning
units, lights etc.
• Pointing the detector towards objects that may move in the wind, such as
curtains, tall plants etc.
ºC
40
ºC
40
5
Detection Range:
LED200PIR: Recommended installation height is 2.5 meter above ground, the
maximum detection range about 10 meter and at the angle of about 140 deg.
3m
ºC
40
1.8m to 2.5 Meter
3 Meter
10 Meter
10m
140º
Page 7
Walk Test and Adjustment
The purpose of Walk Test is used to test and adjust the detection coverage of
LED200PIR under auto mode.
• Adjust the Time knob to “T”, then conduct a walk test as described in test
procedure.
Test procedure:
• Adjust the Time knob to “T”, (Lux knob can be “Sun” or Moon”).
• Switch power on.
• Walk across the detection area, once the detector is triggered and the lamp will
turn On for 2 seconds.
Note walking direction when performing test.
2 sec
6
Test mode
Detector Head Adjustment
The detector head can be panned 90 deg.
to the left and 90 deg. to the right.
90º
90º
Page 8
Knob Settings
LED200PIR has two adjustment knobs:
Time and Lux at the bottom of the detector head.
• Adjust knobs carefully with hand.
TIME knob setting
• You can set the time knob from 5 sec to about 10 min, LED200PIR will turn
On the lamp, for the time duration set after each detected movement.
• Adjust the knob as desired.
LUX knob setting
• When setting the Lux knob at “MOON”, LED200PIR will only operate in
the dark.
• When setting the Lux knob at “SUN”, LED200PIR will operate in any
light level.
7
Turn On Time Adjustment Environment LUX Level to Turn On
5 sec
Dusk Setting (Time knob setting)
• When setting the Time knob to “D”, the motion detector of LED200PIR won’t function.
The lamp will operate depending on the “LUX” level, ie Dusk to Dawn..
10 min
=
Page 9
Lamp turns On
at night.
Setting Advise
Lens masking
8
The purpose of the lens mask is to mask out areas not desired for detection.
Lens mask fi tting procedure:
• Use a penknife or pliers to cut out lens mask segment, exposing area
for detection.
• Attach the lens mask to the detector head.
• Turn slightly the lens mask for it to be locked into place.
A
Lamp turns On at day
& night.
B
Page 10
Lamp Adjustment
The lamp can be tilted down 85 deg. and pan outwardly 40 deg.
40º
40º
9
High Temperature
The temperature of the lamp is very high during operating. You will get hurt,
if you touch the heat sink.
+40ºC
40
30
-20ºC
20
10
85º
40
30
20
10
Page 11
10
3 Year Guarantee
In the unlikely event of this product becoming faulty due
to defective material or manufacture within 3 years of the
date of purchase, please return it to your supplier in the
first year with proof of purchase and it will be replaced free
of charge. For years 2 and 3 or any difficulty in the first year telephone
the helpline on 020 8450 0515.
Page 12
HELPLINE
020 8450 0515
or email helpline@timeguard.com
For a product brochure please contact:
Timeguard Limited.
Victory Park, 400 Edgware Road,
London NW2 6ND
Sales Offi ce: 020 8452 1112
or email csc@timeguard.com
Zerofour – August 2011
Designed in the U.K. 67-058-418
Loading...