Time Electronics 7007 Specifications

Time Electronics

7006 and 7007 Loop-Mates

• Pocket sized 140 x 65 x 30mm

• 4 - 20mA or 0 - 10V loops

• 7 calibration set-points

• TxSim and RxTest (Loop-Mate1)

• RxSim and TxTest (Loop-Mate2)

• Auto-Step output - adjustable rate

• Battery powered PP3

• Internal loop drive supply

DESCRIPTION

The Loop-Mates are single function low-cost pocket sized units, designed for test and calibration of process loops.
Simplicity of operation is their key - no keypads or complicated selections. Engineers will be able to pick them up and
get to work immediately. Just select 4 - 20mA, or 10V loop, and TxSim, RxTest, RxSim or TxTest. Both have internal loop
drive supplies, which can be used to power the loop if required.

Loop-Mate 1 is the simulator and acts as a source to provide the loop signals, 4 - 20mA or 0 - 10V. No complicated
selection of the output, just operate up/down buttons to increase or decrease the signal. There are 7 set-points, 0%,
10%, 25%, 50%, 75%, 90%, 100%. Each is indicated on a high brightness LED and an audible beep sounds as you step
between them. Auto-stepping mode (adjustable rate) allows Loop-Mate1 to be left connected stepping up and down.
The engineer can then move to another location to check (using Loop-Mate 2) that the signal is arriving correctly and is

within specication.

Loop-Mate 2 is a dedicated loop signal indicator, just as easy to operate. Once again select the loop type, 4 - 20mA, or
0 - 10V, and whether you want the display in direct units, or % of span. The LCD display shows the signal to an accuracy
of 0.05% either in mA, V, or % of span.

Both units are powered by a single standard PP3 battery that gives up to 40 hours continuous use.

SPECIFICATIONS

7006 Loop-Mate 1 7007 Loop-Mate 2

Range ............................................................. 4 - 20mA, or 0 - 10V

Set-Points ...............................0, 10, 25, 50, 75, 90, 100% of span

Accuracy .................................................................................0.1%

Modes ................................................................. TxSim, or RxTest

Loop Supply ...................................................Internal, 25mA max

Auto-Step .........................Up/Down/Up, 0.5, 1, 2, 4, or 8sec/step

Power ........................................PP3 battery, typical life 40 hours

Dimensions / Weight .................... H140 x W65 x D30mm / 180g

ORDERING INFORMATION

7006 ................................................................ Loop-Mate 1: Loop Simulator/Source

7007 ................................................................ Loop-Mate 2: Loop Signal Indicator

C145 ................................................................ Factory Calibration Certicate (NPL) – Code applies to 7006 & 7007

C144 ................................................................ UKAS Calibration Certicate (17025) – Code applies to 7006 & 7007

Range .................................................... 4 - 20mA, 0 - 10V, 0 - 50V

Display ..................................... LCD 4 digits, mA, V, or % of span

Accuracy .............................................................................. 0.05%

Modes ...............................RxSim, TxTest, or 50mA/50V measure

Loop supply ....................................................Internal, 25mA max

Power ........................................PP3 battery, typical life 40 hours

Dimensions / Weight .................... H140 x W65 x D30mm / 200g

Both Loop-Mates are supplied with carry case and user manual

Due to continuous development Time Electronics reserves

the right to change specifications without prior notice.

Time Electronics Ltd, Unit 11 Sovereign Way, Botany Industrial Estate, Tonbridge, Kent, TN9 1RH. United Kingdom.

T: [phone] F: [phone] E: [e-mail]

www.timeelectronics.com

v1c 22/3/11