Timberk TIR HP1 1800 User manual
Instruction manual
Руководство по эксплуатации
Инфракрасный
электрический
обогреватель
Модели/Models:
Руководство по эксплуатации включает в себя гаратийный талон
Outlook of devices, aslo colour scores can be revised without any special advance
notices.
Производитель вправе менять внешний вид прибора и цветовую гамму прибора без специального уведомления.
Electric
ceiling heater
(infrared heater)
TIR HP1 1500
TIR HP1 1800
Dear customer!
Thank you for good choice and purchase of the TIMBERK
infrared heater. It will serve long.
Electric infrared heater TIMBERK is designed for general,
additional or local heating of living and production premises,
and also can be used outdoors. The heater can be installed on
the ceiling, ceiling constructions, wall, rack mounting horizontal
arrangement of a longitudinal axis. In places where it is possible
to connect to the electrical wiring with single-phase power
supply to 220V~, 50Hz. This heater is effective and efficient in
use in connection with the minimal losses of electricity.
WARNING!
This heater is not equipped with a device to control
the room temperature. Do not use this heater in small
rooms when they are occupied by persons not capable
of leaving the room on their own, unless constant
supervision is provided.
After the heater is fixed on the base and poles, the
heater must be at least 1.8 meter above the ground.
2. PRECAUTIONS
1. IMPORTANT INFORMATION
Please carefully read the Operation Manual before using the infrared heater.
This Operation Manual contains the important information on your safety,
as well as some recommendations on proper use of the appliance and its
maintenance.
Keep the Operation Manual along with the warranty certificate, sales
receipt, and, if possible, cardboard package and packing material.
The purchased infrared may somewhat differ from one described in the
Manual, but this does not affect the methods of use and operation.
Important precautions and instructions given in this Manual do not include all
possible modes and situations, which can be encountered. It is necessary
to understand that common sense, cautiousness, and carefulness are the
factors, which cannot be «integrated» to any product.
These factors should be considered by the person, who is interested in
proper operation of the device. The manufacturer is not responsible for
damage of the appliance or its components during transportation, as a
result of incorrect installation, as a result of voltage surges, as well as in the
event of changes or modifications in any part of the appliance.
2
www.timberk.com • electric ceiling heater
During use of the infrared heater, it is necessary to observe some
precautions. Improper operation with disregard of precautions may result
in infliction of harm to health of the user and other people, as well as in
infliction of damage to their property.
1.Read all instructions before using the heater.
2.The temperature of the safety grille and body at the heater can reach
very high values. To avoid burns, do not touch the hands and other
body parts to the surfaces of the device, as well as prevent the ability to
touch, including accidental person in the heater through training and the
placement of the device in a safe place.
3.The heater should be placed far from flammable and easily deformable
objects.
4.The device is not equipped with the device temperature adjustment. Do
not use the device in small rooms, when they are people or animals who
cannot leave on their own.
5.The power cord and other objects should not contact hot surfaces of
the heater.
6.Make sure that the heater body and its radiating boards get cold before
demounting and placing the heater to the package for long storage.
7. During demounting of the heater or its movement, take special
precautions to exclude hits of the appliance and its falling.
8.When the heater is not used for a long time, keep it in dry cool place in
the factory cardboard package.
9.DO NOT COVER the heater. Do not dry clothes and any other fabrics/
materials on the appliance. This may lead to its overheating, breakdown, or
infliction of a significant damage to you and/or your property.
IMPORTANT!
The manufacturer considers this type of failure a nonguaranteed event.
10.The heater should be connected to the electric mains equipped with an
automatic circuit breaker.
11.If you plan to use the device in the bathroom or rooms with high humidity,
it must be installed so that the user could not touch the appliance, including
by accident. The device should not be exposed directly to water stream or
direct ingress of moisture on the instrument housing.
12.Never try to repair the heater yourself. This may inflict harm to your
health and affect the warranty service of the appliance.
13.Do not use this device in the place of permanent location of the animals
or plants.
14. It is prohibited to use a heater near inflammable, easily deformable
items and/or substances.
15.Exclude operation of the heater without grounding.
16.Do not leave the appliance unattended during its operation.
17.Throughout enable and use the heater with the removed elements of
the enclosure.
18. Do not operate any appliance with a damaged cord or plug. A
damaged power cord must be replaced by an authorized service center
for the manufacturer.
19.It is prohibited to use the heater in dusty rooms and during redecoration.
20.During operation of the device is forbidden to touch the case and its
protective grille.
21.Use the heater only as described in this Manual. Any other use not
recommended by the manufacturer may lead to fire, electric shock, or
injuries of people.
22.Never clean the heater, when it is connected to the electric mains, and
do not wipe the heater radiating boards with flammable liquids during its
operation.
23. For normal operation of the heater, the mains voltage should be
sufficient and the mains specifications should strictly correspond to the
technical parameters indicated on the appliance body. If necessary, clarify
the specifications of your mains from the electricity supplier.
24. Install and operate the heater with horizontal arrangement of a
longitudinal axis on the ceiling, ceiling constructions, wall. The thermal
resistance of the material shall be not less than 80 °C.
25.It is prohibited to install the appliance in immediate proximity to an electric
socket. This may result in its overheating causing an emergency situation.
26.The appliance is not designed for use by people (including children)
with limited physical, sensory, or mental capabilities and having insufficient
experience/knowledge, if they are not supervised and instructed on use of
the device by a person responsible for their safety.
It is necessary to watch that children do not play with the heater.
3. WORKING PARAMETERS
Operation principle
The infrared heater is an appliance with an electric heating element and
radiating boards, which upon heating emit heat to the environment via
directed infrared radiation. Radiant energy is absorbed by the surrounding
surfaces and it heats them being transformed to thermal energy.
Surface temperature of objects can be different depending on their
absorbing properties (surface color, material), incidence angle of infrared
beams, surface shape and area. Surfaces also release some heat to air.
At that, heated air flows up to the ceiling and gradually cools down. As
a result, air temperature at the head level of a standing person appears
below the floor temperature by 1-2 °C.
Main features
1.Significant economic effect as compared to convectional heating, where
heat is significantly consumed for heating of unused roof space (first, air
is heated throughout the room volume, and then air heats objects and
surfaces in the room).
2.Capability of local heating only for those areas in the room, where it is
necessary, without heating of the whole room volume.
3.Low air temperature in the room at comfortable temperature on surfaces
of objects, floor, and walls creates the freshness effect air is not dried up.
4.Low convection (thermal movement of air volumes) reduces amount of
dust kicked up from the floor.
5.High protection class of the device (IP65) allows to apply the device in
www.timberk.com • electric ceiling heater
3
environments with the most adverse conditions.
6.The possibility of using the device in a portable rack. (Portable stand
comes separately as accessory)
Area of application
Infrared heaters are designed for general, additional, and local heating of
industrial, production, utility, and similar rooms (flats, offices, trade enterprises,
exercise rooms, educational institutions, public catering enterprises, storage
facilities, hangars, agricultural facilities, etc.) and can be used outdoors.
Technical specifications
Table 1.
Parameter
Rated power consumption W 1500 1800
Rated current A 6,8 8,2
Rated voltage V/Hz 220~/50 220~/50
Water protection class - IP65 IP65
Electric protection class
Heating area m
Rated suspension height m 2,0 2,2
Weight kg 2,4 2,6
Dimensions mm 133х558х88 133х658х88
For more detailed description of technical parameters and specifications please refer to our
website www.timberk.com or ask from the official dealers of TIMBERK.
Meas.
units
TIR HP1 1500 TIR HP1 1800
-
2
Class I Class I
14-16 17-19
Item
IMPORTANT!
The manufacturer reserves the right to change the set-list of the
device (including liquid and powder components) for different
supplies without prior notice. The changes either in no way influence
the basic technical parameters of the device or may improve them,
and also not violate the legislation or quality standards of the
countries of manufacture, transit and selling.
The changes in the set-list may result in changing of the weight
and dimensions of the device, but not more than by +\- 5-20%
(depending on the product category)
NOTE:
Heated area in the table is indicated for reference, since it depends
both on the heater power, and on room type, ceiling height, wall/
ceiling materials, number and area of glazing, presence of doors,
etc.
4. INFRARED HEATER DESCRIPTION
Fig.1
Infrared Heater description
1.Heater body
2.Protective grille
3.Heating element
4.Cover
5.Power cord and plug
5. DELIVERY SET
1.Infrared heater – 1 pcs
2.Fasteners kit – 1 pcs
3.Operation manual – 1 pcs
4.Warranty certificate – 1 pcs
5.Package – 1 pcs
4
www.timberk.com • electric ceiling heater
NOTE:
To improve the product quality, the design and technical
specifications of the infrared heater, as well as its delivery set can be
modified by the manufacturer without preliminary notification.
6. INSTALLATION
WARNING!
Mounting of the infrared heater and its connection to the
electric mains should be carried out only by qualified
specialists according to the Electrical Installation
Regulations and Power System Safety Standards.
1.Expand the original packaging and carefully remove the heater
2.Remove the mounting kit
3.Collect the installation wall mount holes as shown in Fig. 2
4.Connect the hardware to the instructions shown in Fig. 3, 4, 5
5.Hang the heater on the smooth surface of the wall with the observance
of the distance specified in item 6.1. Make sure that the mounting screws
firmly fastened
6.If necessary, install the heater, bracket, follow the instructions shown on
Fig. 6, 7, 8, 9 and specified in item 6.3
NOTE:
Depending on material and design of ceiling structural elements, the
heater is secured onto appropriate fasteners chosen on basis of the
strength condition. Strength of the ceiling or structural elements, to
which the heater is secured, should be sufficient to endure 5-fold
weight of the heater.
6.1Safe distances required for installation
1.Never install the unit on the surface of plastic, nylon, cardboard and
other
2.After installing the unit, the distance from the floor should not be less
than 1.8 meters
3.Distance from a wall to a device must be at least of 0.65 meters
4.The distance from the device to a ceiling should be no less than 0.3
meters
5.The distance from the protective grille device to easily flammable (cloth,
paper, plastic and other) and combustible materials must be at least 1.5-2
meters
6.The distance from the device to find the man should be not less than
1 meter
6.2Installation of the heater using the wall fasteners
Table 2.
№ Parts name Specification Qty
1 Screw M6x20 1
2 Bracket set Aluminum 1
3 Expansion bolt M6x60 2
4 Hanger STEEL 1
5 Bolt M8х60 1
5A Nut M8 1
On Fig. 2, 3, 4, 5 shows stepwise instructions on assembly and installation
of wall fasteners for infrared heater.
www.timberk.com • electric ceiling heater
5
Fig. 2 Fig. 4
Fig. 3 Fig. 5
6
www.timberk.com • electric ceiling heater
6.3Installing the infrared heater on a portable rack
Table 3.
Series Parts name Specification Qty
1 Screw M6x20 1
2 Bracket set Aluminum 1
3 Expansion bolt M6x60 2
4 Hanger Steel 1
5 Bolt M8х60 1
5A Nut M8 1
6 Nut M6 4
7 Bracket 3 Aluminum 1
8 Bolt M6х10 12
9 Telescopic tube set Steel 1
10 Telescopic tube Steel 1
11 Telescopic tube Steel 1
12 Base Plastic 1
13 M8 bolt L shpae 1
14 Fixing plate Steel 1
15 Base cover Steel 1
16 Bolt M6x50 3
17 Spring washer Ф6.2хФ8.2х1 3
18 Washer Ф6.2хФ14х1 3
19 Decorative cover Steel 1
20 Hex wrench Steel 1
21 wire holder PA 2
22 Telescopic tube cover Silicone 1
Fig. 6
Fig. 7
On Fig. 6, 7, 8, 9 shows stepwise instructions on assembly and installation
of infrared heater on the mobile rack.
Fig. 8
www.timberk.com • electric ceiling heater
7
WARNING!
After installation of the heater and before switching for
the first time, it is necessary to wipe the radiating board
with alcohol. After that, it is PROHIBITED to touch the
radiating board.
Connection to electric mains
1.The patio heater is designed to be connected to 220V~, 50Hz singlephase voltage mains with a grounding circuit.
2.Prior to connection make sure that parameters of electric mains in the
place of connection comply with parameters, indicated on the identification
plate with technical data of the unit.
3.It is necessary to follow active electrical safety precautions, connecting
the convector to electric mains.
4. An electric outlet must be properly grounded. The outlet must be
designed for rated current not less than 16A for models with maximum
power up to 2000W. Electric outlet and plug must always stay dry to
prevent current leakage. Regularly check if the electric plug is tightly
connected to the outlet. It must be done in the following order: connect an
electric plug into an outlet, after half hour operation turn off the patio heater
and disconnect the plug from the outlet, check if the plug is heated by your
hand. If the plug heated over 50°C then replace the outlet by a new one
to prevent damages, incidents, fire as a result of bad electric contact. A
specialist must do the job.
7. OPERATION OF THE INFRARED HEATER
WARNING!
Warning! Please connect the cable with an industrial
plug rated 3P 230V~ 16A IP67 of IEC 60309-2
1.Before switching on the heater, ensure that no moisture on the device
and on the heating element.
Fig. 9
8
www.timberk.com • electric ceiling heater
2.After the first turn the heater on may appear briefly burnt smell. This
Loading...